Date: Fri, 7 Jul 2000 23:23:13 -0400 From: "dave" <dmehler22@earthlink.net> To: "Adam" <bsdx@looksharp.net> Cc: <freebsd-hardware@freebsd.org> Subject: Re: configuring a pnp modem. Message-ID: <000801bfe88b$db78f9e0$0200a8c0@hellraiser> References: <Pine.BSF.4.21.0007061927090.1323-100000@turtle.looksharp.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hello, Thanks for the reply. Below is the output of pnpinfo, I hope it helps. Again, I'm using fbsd 4.0-release. Thanks. Dave. Checking for Plug-n-Play devices... Card assigned CSN #1 Vendor ID CTL002b (0x2b008c0e), Serial Number 0x1008505d PnP Version 1.0, Vendor Version 32 Device Description: Creative SB16 PnP Logical Device ID: CTL0031 0x31008c0e #0 Device Description: Audio TAG Start DF Good Configuration IRQ: 5 - only one type (true/edge) DMA: channel(s) 1 8-bit, not a bus master, count by byte, , Compatibility mode DMA: channel(s) 5 16-bit, not a bus master, , count by word, Compatibility mode I/O Range 0x220 .. 0x220, alignment 0x1, len 0x10 [16-bit addr] I/O Range 0x330 .. 0x330, alignment 0x1, len 0x2 [16-bit addr] I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4 [16-bit addr] TAG Start DF Acceptable Configuration IRQ: 5 7 10 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode DMA: channel(s) 5 6 7 16-bit, not a bus master, , count by word, Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2 [16-bit addr] I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4 [16-bit addr] TAG Start DF Acceptable Configuration IRQ: 5 7 10 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode DMA: channel(s) 5 6 7 16-bit, not a bus master, , count by word, Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2 [16-bit addr] TAG Start DF Sub-optimal Configuration IRQ: 5 7 10 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode DMA: channel(s) 5 6 7 16-bit, not a bus master, , count by word, Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] TAG Start DF Sub-optimal Configuration IRQ: 5 7 10 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2 [16-bit addr] I/O Range 0x388 .. 0x388, alignment 0x1, len 0x4 [16-bit addr] TAG Start DF Sub-optimal Configuration IRQ: 5 7 10 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] I/O Range 0x300 .. 0x330, alignment 0x30, len 0x2 [16-bit addr] TAG Start DF Sub-optimal Configuration IRQ: 5 7 10 11 - only one type (true/edge) DMA: channel(s) 0 1 3 8-bit, not a bus master, count by byte, , Compatibility mode I/O Range 0x220 .. 0x280, alignment 0x20, len 0x10 [16-bit addr] TAG End DF Logical Device ID: CTL2011 0x11208c0e #1 Compatible Device ID: PNP0600 (0006d041) Device Description: IDE TAG Start DF Good Configuration IRQ: 10 - only one type (true/edge) I/O Range 0x168 .. 0x168, alignment 0x1, len 0x8 [16-bit addr] I/O Range 0x36e .. 0x36e, alignment 0x1, len 0x2 [16-bit addr] TAG Start DF Acceptable Configuration IRQ: 11 - only one type (true/edge) I/O Range 0x1e8 .. 0x1e8, alignment 0x1, len 0x8 [16-bit addr] I/O Range 0x3ee .. 0x3ee, alignment 0x1, len 0x2 [16-bit addr] TAG Start DF Acceptable Configuration IRQ: 10 11 15 - only one type (true/edge) I/O Range 0x180 .. 0x1b8, alignment 0x8, len 0x8 [16-bit addr] I/O Range 0x306 .. 0x33e, alignment 0x8, len 0x2 [16-bit addr] TAG Start DF Sub-optimal Configuration IRQ: 15 - only one type (true/edge) I/O Range 0x170 .. 0x170, alignment 0x1, len 0x8 [16-bit addr] I/O Range 0x376 .. 0x376, alignment 0x1, len 0x1 [16-bit addr] TAG End DF Logical Device ID: CTL0051 0x51008c0e #2 Device Description: StereoEnhance I/O Range 0x100 .. 0x138, alignment 0x8, len 0x1 [16-bit addr] Logical Device ID: CTL7001 0x01708c0e #3 Device Description: Game I/O Range 0x200 .. 0x200, alignment 0x1, len 0x8 [16-bit addr] End Tag Successfully got 71 resources, 4 logical fdevs -- card select # 0x0001 CSN CTL002b (0x2b008c0e), Serial Number 0x1008505d Logical device #0 IO: 0x0220 0x0220 0x0220 0x0220 0x0220 0x0220 0x0220 0x0220 IRQ 5 0 DMA 1 5 IO range check 0x00 activate 0x01 Logical device #1 IO: 0x03ee 0x03ee 0x03ee 0x03ee 0x03ee 0x03ee 0x03ee 0x03ee IRQ 11 0 DMA 4 4 IO range check 0x00 activate 0x01 Logical device #2 IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 IRQ 0 0 DMA 4 4 IO range check 0x00 activate 0x01 Logical device #3 IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 IRQ 0 0 DMA 4 4 IO range check 0x00 activate 0x01 Card assigned CSN #2 Vendor ID USR3030 (0x30307256), Serial Number 0xaebc8fb4 PnP Version 1.0, Vendor Version 0 Device Description: U.S. Robotics 56K FAX INT Logical Device ID: USR3030 0x30307256 #0 TAG Start DF Good Configuration I/O Range 0x2f8 .. 0x2f8, alignment 0x8, len 0x8 [16-bit addr] IRQ: 3 5 7 - only one type (true/edge) TAG Start DF Acceptable Configuration I/O Range 0x3f8 .. 0x3f8, alignment 0x8, len 0x8 [16-bit addr] IRQ: 2 3 4 5 7 - only one type (true/edge) TAG Start DF Acceptable Configuration I/O Range 0x3e8 .. 0x3e8, alignment 0x8, len 0x8 [16-bit addr] IRQ: 2 3 4 5 7 - only one type (true/edge) TAG Start DF Acceptable Configuration I/O Range 0x2e8 .. 0x2e8, alignment 0x8, len 0x8 [16-bit addr] IRQ: 2 3 4 5 7 - only one type (true/edge) TAG Start DF Acceptable Configuration TAG End DF End Tag Successfully got 17 resources, 1 logical fdevs -- card select # 0x0002 CSN USR3030 (0x30307256), Serial Number 0xaebc8fb4 Logical device #0 IO: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 IRQ 0 0 DMA 4 4 IO range check 0x00 activate 0x01 ----- Original Message ----- From: "Adam" <bsdx@looksharp.net> To: "dave" <dmehler22@earthlink.net> Cc: <freebsd-hardware@FreeBSD.ORG> Sent: Thursday, July 06, 2000 7:28 PM Subject: Re: configuring a pnp modem. > I had one working in 2.2.x or 3.x a few years ago, but since the pnp > system is different now you'll probably have to glean some identification > info from the pnpinfo command and stuff it in the sio driver so it > recognizes and configures the modem. If you cant handle all this, at > least post back with the pnpinfo output so someone else can give it a > shot. Good luck! > > On Fri, 7 Jul 2000, dave wrote: > > >Hello, > > Has anyone got a plug and play modem, not a winmodem, working under fbsd 4.0? If so, please tell me how as I have been unable to get mine working. > >Thanks. > >Dave. > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?000801bfe88b$db78f9e0$0200a8c0>