Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 10 Jan 2005 13:21:58 -0800
From:      Steve Kargl <sgk@troutmask.apl.washington.edu>
To:        freebsd-current@freebsd.org
Subject:   ATA panic
Message-ID:  <20050110212158.GA70082@troutmask.apl.washington.edu>

next in thread | raw e-mail | index | archive | help
Hand transcribed

Fatal trap 12: page fault while in kernel mode
fault virtual address     = 0xff70ff90
fault code                = supervisor read, page not present
instruction pointer       = 0x8:0xc0641091
stack pointer             = 0x10:0xc0c20c58
frame pointer             = 0x10:0xc0c20c78
code segement             = base 0x0, limit 0xfffff, type 0x1b
                          = DPL 0, pres 1, def32 1, gran 1
processor eflages         = interrupt enabled, resume, IOPL = 0
current process           = 0 (swapper)
[thread pid 52 tid 100040]
Stopped at mtrash_ctor+0x63:   movl  0x20(%eax),%edx

db> trace
mtrash_ctor(c1bc9600,200,0,1,c0c20b8) at mtrash_ctor+0x63
uma_zalloc_arg(c10456c0,0,1,c1046be0,c1979ac) at uma_zalloc_arg+0x46c
malloc(200,c06f5760,1,950a,c0c20d40) at malloc+0x87
ata_getparam(10,3f,200,c1bc9800,c1979a00) at ata_getparam+0x38
ata_identify_device(c1a7f080,1,c19fc990,c197296c,c0c20d78) at
   ata_identify_device+0xfc
ata_boot_attach(0,c0545d5f,c072c9e0,0,c06d15d7) at ata_boot_attach+0x40
run_interrupt_driven_config_hooks(0,0,c197299c,c1ec00,c1e000) at 
   run_interrupt_driven_config_hooks+0x22
mi_startup() at mi_startup()+0xb1

Verbose dmesg from last working kernel follows .sig.

-- 
Steve


Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #5: Sun Nov 14 13:24:03 PST 2004
    root@kargl.stms.org:/usr/obj/usr/src/sys/MOBILE
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/sgk/kernel" at 0xc086f000.
Preloaded elf module "/boot/sgk/vesa.ko" at 0xc086f14c.
Preloaded elf module "/boot/sgk/snd_ich.ko" at 0xc086f1f4.
Preloaded elf module "/boot/sgk/sound.ko" at 0xc086f2a0.
Preloaded elf module "/boot/sgk/umodem.ko" at 0xc086f348.
Preloaded elf module "/boot/sgk/ucom.ko" at 0xc086f3f0.
Preloaded elf module "/boot/sgk/agp.ko" at 0xc086f498.
Preloaded elf module "/boot/sgk/radeon.ko" at 0xc086f540.
Preloaded elf module "/boot/sgk/uplcom.ko" at 0xc086f5e8.
Calibrating clock(s) ... i8254 clock: 1193139 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1994126872 Hz
CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz (1994.13-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
  Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  = 536748032 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c26000 - 0x000000001f6b1fff, 514375680 bytes (125580 pages)
avail memory = 516014080 (492 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry = 0xffe90 (c00ffe90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xbfee
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry = f0000:e2f4  Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
mem: <memory>
Pentium Pro MTRR support enabled
io: <I/O>
VESA: information block
56 45 53 41 00 02 00 01 00 01 01 00 00 00 22 00 
00 01 00 01 00 01 19 01 00 01 2f 01 00 01 34 01 
00 01 82 01 0d 01 0e 01 0f 01 20 01 92 01 93 01 
94 01 95 01 96 01 a2 01 a3 01 a4 01 a5 01 a6 01 
VESA: 60 mode(s) found
VESA: v2.0, 16384k memory, flags:0x1, mode table:0xc0807c42 (1000022)
VESA: ATI MOBILITY RADEON 7500
VESA: ATI Technologies Inc. P7   01.00
null: <null device, zero device>
acpi0: <DELL CPi R  > on motherboard
acpi0: [MPSAFE]
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80010014
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=00] is there (id=1a308086)
pcibios: BIOS version 2.10
Found $PIR table, 11 entries at 0xc00fbb90
PCI-Only Interrupts: none
Location  Bus Device Pin  Link  IRQs
embedded    0   29    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    B   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   29    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   30    D   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    0   31    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    0   31    B   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    1    0    A   0x60  3 4 5 6 7 9 10 11 12 14 15
embedded    2    0    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2    1    A   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    A   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    2    3    B   0x63  3 4 5 6 7 9 10 11 12 14 15
embedded    2    8    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2   12    A   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2   12    B   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2   12    C   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    2   12    D   0x62  3 4 5 6 7 9 10 11 12 14 15
embedded    8    0    A   0x61  3 4 5 6 7 9 10 11 12 14 15
embedded    8    1    A   0x61  3 4 5 6 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
atpic: Programming IRQ9 as level/low
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 29 func 2
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU (2 Cx states)> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI link \\_SB_.PCI0.LNKB has invalid initial irq 11, ignoring
ACPI PCI link initial configuration:
\\_SB_.PCI0.LNKA irq  0: [ 9 10 11] 11+ low,level,sharable 0.31.0
\\_SB_.PCI0.LNKB irq  0: [ 5  7]  0+ low,level,sharable 0.31.1
\\_SB_.PCI0.LNKC irq  0: [ 9 10 11] 11+ low,level,sharable 0.31.2
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 0.31.3
\\_SB_.PCI0.LNKA irq  0: [ 9 10 11] 11+ low,level,sharable 0.29.0
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 0.29.1
\\_SB_.PCI0.LNKC irq  0: [ 9 10 11] 11+ low,level,sharable 0.29.2
\\_SB_.PCI0.LNKA irq  0: [ 9 10 11] 11+ low,level,sharable 0.2.0
\\_SB_.PCI0.LNKA irq  0: [ 9 10 11] 11+ low,level,sharable 0.1.0
\\_SB_.PCI0.LNKB irq  0: [ 5  7]  0+ low,level,sharable 0.1.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
	map[10]: type 3, range 32, base e8000000, size 26, enabled
found->	vendor=0x8086, dev=0x1a30, revid=0x04
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x1a31, revid=0x04
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000bf80, size  5, enabled
pcib0: matched entry for 0.29.INTA (src \\_SB_.PCI0.LNKA)
pcib0: possible interrupts:  9 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKB (references 2, priority 5130):
	interrupts:	     5     7
	penalty:	    90  5040
\\_SB_.PCI0.LNKD (references 2, priority 2180):
	interrupts:	    11    10     5     9     7
	penalty:	    80    80    90   160  5040
\\_SB_.PCI0.LNKA (references 4, priority 426):
	interrupts:	    11    10     9
	penalty:	    80    80   160
\\_SB_.PCI0.LNKC (references 2, priority 213):
	interrupts:	    11    10     9
	penalty:	    80    80   160
pcib0: slot 29 INTA routed to irq 11 via \\_SB_.PCI0.LNKA
found->	vendor=0x8086, dev=0x2482, revid=0x02
	bus=0, slot=29, func=0
	class=0c-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
found->	vendor=0x8086, dev=0x2448, revid=0x42
	bus=0, slot=30, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x8086, dev=0x248c, revid=0x02
	bus=0, slot=31, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000bfa0, size  4, enabled
found->	vendor=0x8086, dev=0x248a, revid=0x02
	bus=0, slot=31, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=255
	map[10]: type 4, range 32, base 0000d800, size  8, enabled
	map[14]: type 4, range 32, base 0000dc80, size  6, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB)
pcib0: possible interrupts:  5  7
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKB (references 2, priority 5210):
	interrupts:	     5     7
	penalty:	   130  5080
\\_SB_.PCI0.LNKD (references 2, priority 2356):
	interrupts:	     5    10    11     9     7
	penalty:	   130   160   200   320  5080
\\_SB_.PCI0.LNKC (references 2, priority 453):
	interrupts:	    10    11     9
	penalty:	   160   200   320
atpic: Programming IRQ5 as level/low
pcib0: slot 31 INTB routed to irq 5 via \\_SB_.PCI0.LNKB
found->	vendor=0x8086, dev=0x2485, revid=0x02
	bus=0, slot=31, func=5
	class=04-01-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
	map[10]: type 4, range 32, base 0000d400, size  8, enabled
	map[14]: type 4, range 32, base 0000dc00, size  7, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB)
pcib0: slot 31 INTB is already routed to irq 5
found->	vendor=0x8086, dev=0x2486, revid=0x02
	bus=0, slot=31, func=6
	class=07-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
agp0: <Intel 82845 host to AGP bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xc000-0xcfff
pcib1:   memory decode     0xfc000000-0xfdffffff
pcib1:   prefetched decode 0xe0000000-0xe7ffffff
ACPI PCI link initial configuration:
\\_SB_.PCI0.LNKA irq*11: [ 9 10 11] 11+ low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
	map[10]: type 3, range 32, base e0000000, size 27, enabled
pcib1: device (null) requested decoded memory range 0xe0000000-0xe7ffffff
	map[14]: type 4, range 32, base 0000c000, size  8, enabled
pcib1: device (null) requested decoded I/O range 0xc000-0xc0ff
	map[18]: type 1, range 32, base fcff0000, size 16, enabled
pcib1: device (null) requested decoded memory range 0xfcff0000-0xfcffffff
pcib1: matched entry for 1.0.INTA (src \\_SB_.PCI0.LNKA)
pcib1: slot 0 INTA is already routed to irq 11
found->	vendor=0x1002, dev=0x4c57, revid=0x00
	bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x01a7, statreg=0x02b0, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
drm0: <ATI Radeon LW Mobility 7500 M7> port 0xc000-0xc0ff mem 0xfcff0000-0xfcffffff,0xe0000000-0xe7ffffff irq 11 at device 0.0 on pci1
info: [drm] AGP at 0xe8000000 64MB
info: [drm] Initialized radeon 1.11.0 20020828 on minor 0
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbf80
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   16
pcib2:   I/O decode        0xe000-0xffff
pcib2:   memory decode     0xf4000000-0xfbffffff
pcib2:   prefetched decode 0xfff00000-0xfffff
pcib2:   Subtractively decoded bridge.
ACPI PCI link initial configuration:
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 2.1.0
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 2.1.1
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 2.1.2
\\_SB_.PCI0.LNKB irq* 5: [ 5  7]  0+ low,level,sharable 2.3.0
\\_SB_.PCI0.LNKD irq  0: [ 5  7  9 10 11] 11+ low,level,sharable 2.3.1
\\_SB_.PCI0.LNKC irq  0: [ 9 10 11] 11+ low,level,sharable 2.0.0
\\_SB_.PCI0.LNKC irq  0: [ 9 10 11] 11+ low,level,sharable 2.8.0
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
	map[10]: type 4, range 32, base 0000ec80, size  7, enabled
pcib2: device (null) requested decoded I/O range 0xec80-0xecff
	map[14]: type 1, range 32, base f8fffc00, size  7, enabled
pcib2: device (null) requested decoded memory range 0xf8fffc00-0xf8fffc7f
pcib2: matched entry for 2.0.INTA (src \\_SB_.PCI0.LNKC)
pcib2: possible interrupts:  9 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKD (references 6, priority 7764):
	interrupts:	     5    10    11     9     7
	penalty:	   250   280   320   440  5180
\\_SB_.PCI0.LNKC (references 4, priority 1386):
	interrupts:	    10    11     9
	penalty:	   280   320   440
pcib2: slot 0 INTA routed to irq 11 via \\_SB_.PCI0.LNKC
found->	vendor=0x10b7, dev=0x9200, revid=0x78
	bus=2, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found->	vendor=0x104c, dev=0xac51, revid=0x00
	bus=2, slot=1, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 1  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base 00000000, size 12, memory disabled
found->	vendor=0x104c, dev=0xac51, revid=0x00
	bus=2, slot=1, func=1
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=255
	powerspec 1  supports D0 D1 D2 D3  current D0
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec80-0xecff mem 0xf8fffc00-0xf8fffc7f irq 11 at device 0.0 on pci2
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xf8fffc00
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x00105a, model 0x0000, rev. 0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:08:74:99:7c:c5
xl0: [MPSAFE]
cbb0: <TI1420 PCI-CardBus Bridge> at device 1.0 on pci2
pcib2: device cbb0 requested decoded memory range 0xf4000000-0xfbffffff
cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xf4000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: matched entry for 2.1.INTA (src \\_SB_.PCI0.LNKD)
pcib2: possible interrupts:  5  7  9 10 11
ACPI PCI link arbitrated settings:
\\_SB_.PCI0.LNKD (references 6, priority 8484):
	interrupts:	     5    10    11     9     7
	penalty:	   350   400   480   560  5280
pcib2: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.LNKD
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
  0x00: 0xac51104c 0x02100007 0x06070000 0x00822008 
  0x10: 0xf4000000 0x020000a0 0x20040400 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 
  0x40: 0x012b1028 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x2024d025 0x00000000 0x00000000 0x01261222 
  0x90: 0x6064a6c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe110001 0x00c00000 0x00000000 0x00000017 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
cbb1: <TI1420 PCI-CardBus Bridge> at device 1.1 on pci2
pcib2: device cbb1 requested decoded memory range 0xf4000000-0xfbffffff
cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0xf4001000
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: matched entry for 2.1.INTA (src \\_SB_.PCI0.LNKD)
pcib2: slot 1 INTA is already routed to irq 11
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
  0x00: 0xac51104c 0x02100007 0x06070000 0x00822008 
  0x10: 0xf4001000 0x020000a0 0x20050500 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x0740010b 
  0x40: 0x012b1028 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x2024d025 0x00000000 0x00000000 0x01261222 
  0x90: 0x6064a6c0 0x00000000 0x00000000 0x00000000 
  0xa0: 0xfe110001 0x00c00000 0x00000000 0x00000017 
  0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xe0: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0xbfa0-0xbfaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xbfa0
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave:  stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: [MPSAFE]
pcm0: <Intel ICH3 (82801CA)> port 0xdc80-0xdcbf,0xd800-0xd8ff irq 5 at device 31.5 on pci0
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xd800
pcm0: Reserved 0x40 bytes for rid 0x14 type 4 at 0xdc80
pcm0: [GIANT-LOCKED]
pcm0: <Cirrus Logic CS4205 AC97 Codec (id = 0x4352595b)>
pcm0: Codec features mic channel, tone, simulated stereo, bass boost, 20 bit DAC, 18 bit ADC, 5 bit master volume, SRS 3D Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, variable rate mic, AMAP
pcm0: sndbuf_setmap 1f423000, 4000; 0xd9489000 -> 1f423000
pcm0: sndbuf_setmap 1f41f000, 4000; 0xd948d000 -> 1f41f000
pcm0: sndbuf_setmap 1f41b000, 4000; 0xd9491000 -> 1f41b000
pci0: <simple comms> at device 31.6 (no driver attached)
pci0:31:6: Transition from D0 to D3
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <ECP parallel printer port> port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xcf800-0xcffff,0xcf000-0xcf7ff,0xc0000-0xcefff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1994126872 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
acpi_cmbat1: battery initialization start
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on Intel ICH3 chip
ata0-master: setting UDMA100 on Intel ICH3 chip
ad0: <IC25N040ATCS05-0/CS4OA63A> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1-slave:  stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: resetting done ..
ata1: reiniting channel ..
ata1-slave: FAILURE - ATAPI_IDENTIFY timed out
ata1: reiniting channel ..
ata1-slave: FAILURE - ATAPI_IDENTIFY timed out
ata1-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata1-master: setting PIO4 on Intel ICH3 chip
ata1: device config done ..
ata1-slave: FAILURE - ATAPI_IDENTIFY timed out
ata1-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata1-master: setting PIO4 on Intel ICH3 chip
acd0: <HL-DT-STDVD-ROM GDR8081N/0108> DVDROM drive at ata1 as master
acd0: read 1722KB/s (4134KB/s), 512KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
pcm0: measured ac97 link rate at 48007 Hz, will use 48000 Hz
Mounting root from ufs:/dev/ad0s3a
start_init: trying /sbin/init
splash: image decoder found: blank_saver
Linux ELF exec handler installed
acpi_cmbat1: battery initialization failed, giving up



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050110212158.GA70082>