Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 03 Apr 1998 17:57:49 -0500
From:      Jason Sabella <jsabella@ic.sunysb.edu>
To:        Doug White <dwhite@resnet.uoregon.edu>, freebsd-questions@FreeBSD.ORG
Subject:   Re: FreeBSD installation
Message-ID:  <3525696D.45F20654@ic.sunysb.edu>
References:  <Pine.BSF.3.96.980403132926.10860R-100000@gdi.uoregon.edu>

next in thread | previous in thread | raw e-mail | index | archive | help
Hi Doug.  I only have the one hard 6.4 GIG hard drive.  I don't know
what that "wd2" is.  Is that possibly a wrong partition?  Is there a way
to change it to a different "wd" in the install program(if such a thing
exists).  My current configuration is this:

C drive (2.1 GIG or 33% of drive)  1839M used, 229M unused
D drive (2.1 GIG or 33% of drive)  1526M used, 590M unused
E drive (no longer exists, used to be the last 33%)

But the installation program still says:
Disk name:  wd2
Disk Geometry: 512 cyls/12 heads/32 sectors = 196608 sectors
Offset    Size    End    Name    Ptype Desc    Subtype   Flags
0         32      31     -       6     unused  0
32        196192  196223 wd2s1   2     fat     6         =
196224    384     196607 -       6     unused  0

What keys do you suggest I type at this screen to get to the right
partition?  Thank you.  Jason Sabella

---


Doug White wrote:
> 
> On Fri, 3 Apr 1998, Jason Sabella wrote:
> 
> > Hi Doug.  I got the Partition resizer program and did what you had
> > said.  I decreased the size of the extended partition down to 2 megs (it
> > was still 4 megs even though I deleted the E drive for some reason).  So
> > now, FIPS prints out:
> >
> > Part|Boot|Head Cyl Sect|System|Head Cyl Sect|Start Sect|Num Sectors|MB
> > 1    yes  1    0   1    06h    254  260 63   63         4192902     2047
> > 2    no   0    261 1    05h    254  521 63   4192965    4192965     2047
> 
> Looks good.  You don't need to use FIPS now.
> 
> > This looks correct because partition 2 no longer says 4094MB, its says
> > 2047.  So the room should be there.  But once again, when I go to
> > install FreeBSD(noice installation), it says no room.  And it still
> > shows the same screen during installation(shown below)...
> >
> > Disk name:  wd2
> > Disk Geometry: 512 cyls/12 heads/32 sectors = 196608 sectors
> > Offset    Size    End    Name    Ptype Desc    Subtype   Flags
> > 0         32      31     -       6     unused  0
> > 32        196192  196223 wd2s1   2     fat     6
> > 196224    384     196607 -       6     unused  0
> 
> These aren't the same disk.  Are you sure you're pointing at the right
> disk?  wd2 would be the first disk on the slave controller.
> 
> Doug White                              | University of Oregon
> Internet:  dwhite@resnet.uoregon.edu    | Residence Networking Assistant
> http://gladstone.uoregon.edu/~dwhite    | Computer Science Major

To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3525696D.45F20654>