Date: Fri, 15 Aug 2003 09:19:52 +0200 From: "SUPPORT" <support@bluetooth-shop.sk> To: "FreeBSD Questions" <freebsd-questions@freebsd.org> Subject: Nwe kernel and dmesg question Message-ID: <000a01c362fd$a1cfbd60$3501a8c0@pro.sk>
next in thread | raw e-mail | index | archive | help
Hello everybody, I'm sorry for the long mail, but I really need your help. Please read it before removing :-) I just have my new kernel (where I disabled almost SCSI devices) but during start-up there are errors as follows: config> di pcic0 No such device: pcic0 Invalid command or syntax. Type `?' for help. config> di bt0 No such device: bt0 Invalid command or syntax. Type `?' for help. config> di aic0 No such device: aic0 Invalid command or syntax. Type `?' for help. config> di aha0 No such device: aha0 Invalid command or syntax. Type `?' for help. config> di adv0 No such device: adv0 Invalid command or syntax. Type `?' for help. config> en ed0 No such device: ed0 Invalid command or syntax. Type `?' for help. config> po ed0 0x280 No such device: ed0 Invalid command or syntax. Type `?' for help. config> ir ed0 10 No such device: ed0 Invalid command or syntax. Type `?' for help. config> iom ed0 0xd8000 No such device: ed0 Invalid command or syntax. Type `?' for help. config> f ed0 0 No such device: ed0 Invalid command or syntax. Type `?' for help. What are these devices ? Why they are there, when I rem all lines concerning about them in my kernel config file ? Also, my machine has Matrox Millenium card. I tried tu set it up into VESA mode and use 132x43 cols/lns, but the last message before showing login screen is: "vidcontrol: cannot set video mode. Operation not supported by device". Matrox was found: VESA: v2.0, 2048k memory, flags:0x1, mode table:0xc030a302 (1000022) VESA: Matrox Graphics Inc. [skipped] pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 11.0 irq 11 but sc0 still goes into VGA mode: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> How to make it to go into VESA mode ? How to make kernel to use Matrox Millenium driver ? The last question is about CD-ROM. Ata is working properly: atapci0: <Generic PCI ATA controller> port 0x2000-0x200f,0-0x3,0-0x7,0-0x3,0-0x7 irq 15 at device 20.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 [skipped] acd0: CDROM <SAMSUNG CD-ROM SC-148C> at ata0-master PIO4 CD-ROM is found, but I still can not use it (mount does not work, writing: READ_TOC command timeout - resetting resetting devices ... done read data overrun 12/0 I encountered this problem during installation, too. I was not able to install FreeBSD from the CD the install boot from, so I installed it from MSDOS partition (I mounted temporarily. I have only one SCSI HDD and ATA CD-ROM in my machine. Why I can not use my CDROM :-( ? Please help, if you can :-) Peter Rosa
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?000a01c362fd$a1cfbd60$3501a8c0>