Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 7 May 2010 14:05:16 -0700
From:      Pyun YongHyeon <pyunyh@gmail.com>
To:        Perevalov Sergey <perevalov84@gmail.com>
Cc:        freebsd-net@freebsd.org
Subject:   Re: [axe][ue0] Device send packets but any host in network can not receive any packet from it.
Message-ID:  <20100507210516.GI14801@michelle.cdnetworks.com>
In-Reply-To: <4BE44E2D.6060907@gmail.com>
References:  <4BE44E2D.6060907@gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, May 07, 2010 at 10:30:21PM +0500, Perevalov Sergey wrote:
> Hi guys. I am beginner in FreeBSD.  And I got problem with my Gigabit 
> usb to ethernet adapter with AX88178 chipset. It works in windows very 
> well but doesn't work in FreeBSD 8.0. tcpdump shows log with received 
> and sent packets, but any host in network doesn't receive them from it.  
> I checked it with 2 FreeBSD hosts connected directly by cable. Can you, 
> guys, advice to me something to fix or to find reason of this issue?
> I started thread on freebsd forums( 
> http://forums.freebsd.org/showthread.php?t=13649 ) and also reported 
> about problem ( http://www.freebsd.org/cgi/query-pr.cgi?pr=146153 ).
> 

It seems the PR shows tcpdump output on sender side(axe(4)
host 192.168.2.22). Would you capture the traffic on receiver side
(host 192.168.2.7) and post the result? Note, please use direct
cable to connect both systems and use option -e to capture traffic
on host 192.168.2.7. For instance, use
#ifconfig -envvvvvvi nic0
on receiver side.

Also check whether the receiver agrees on the resolved speed/duplex
of established link. For your case, host 192.168.2.7 should show
100baseTX, full-duplex.

> Here some information:
> 
> dmesg:
> ugen4.2: <vendor 0x0b95> at usbus4
> axe0: <vendor 0x0b95 product 0x1780, rev 2.00/0.01, addr 2> on usbus4
> axe0: PHYADDR 0xe0:0x02
> miibus0: <MII bus> on axe0
> rgephy0: <RTL8169S/8110S/8211B media interface> PHY 2 on miibus0
> rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
> 1000baseT-FDX, auto
> ue0: <USB Ethernet> on axe0
> ue0: Ethernet address: 00:0e:c6:88:09:4e
> 
> usbconfig:
> laptop# usbconfig
> ugen0.1: <UHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=FULL 
> (12Mbps) pwr=ON
> ugen1.1: <UHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=FULL 
> (12Mbps) pwr=ON
> ugen2.1: <UHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=FULL 
> (12Mbps) pwr=ON
> ugen3.1: <UHCI root HUB Intel> at usbus3, cfg=0 md=HOST spd=FULL 
> (12Mbps) pwr=ON
> ugen4.1: <EHCI root HUB Intel> at usbus4, cfg=0 md=HOST spd=HIGH 
> (480Mbps) pwr=ON
> ugen4.2: <product 0x1780 vendor 0x0b95> at usbus4, cfg=0 md=HOST 
> spd=HIGH (480Mbps) pwr=ON
> ugen0.2: <Optical Mouse Genius> at usbus0, cfg=0 md=HOST spd=LOW 
> (1.5Mbps) pwr=ON
> 
> ifconfig:
> ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
> ether 00:0e:c6:88:09:4e
> inet 192.168.2.22 netmask 0xffffff00 broadcast 192.168.2.255
> media: Ethernet autoselect (100baseTX <full-duplex>)
> status: active
> 
> Thank you for you help!



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20100507210516.GI14801>