Date: Wed, 7 Aug 2002 22:19:51 -0700 (PDT) From: William Blair Wagner <blairwag1965@yahoo.com> To: questions@freebsd.org Subject: Booting errormsg and slow disk? HELP! Message-ID: <20020808051951.2394.qmail@web20808.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
I have a successful installation of FreeBSD4.6-STABLE.
Things are working relatively well. However, I notice
and am concerned about some funny messages that
display during the system boot. I'm concerned that my
hard disk drive is not performing at what it should.
I've got a dual-boot situation. The primary EIDE
master disk drive (40GB) has the dual-boot MDR and
Windows2000pro. The secondary EIDE master disk drive
(20GB) is dedicated to FreeBSD. Both are WesternCaviar
7200rpm ATA100 disk drives. I also have a Pioneer 24X
CD-ROM on the secondary EIDE controller as the slave.
Following is the output of the boot (captured from
dmesg.boot). If you'll notice, I'm getting "UDMA ICRC
error" messages logged when the slices are read up by
theboot processor. What are these? Sometimes, when I
boot, the WD200BB disk drive shows up as UDMA33
instead of UDMA100. Is this because my CD-ROM is on
the same controller? Should I move it. Is there
something poissibly wrong?
I'm also worried about hte 8 messages similar to:
"unknown: <PNP0401> can't assign resources"
...what are these about ...what do they mean ...do I
care?
Thanx for any help you might give, and sorry for the
long email.
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989,
1991, 1992, 1993, 1994
The Regents of the University of California.
All rights reserved.
FreeBSD 4.6-RELEASE #1: Wed Jul 24 22:27:57 EDT 2002
root@bsdblair.blairwag.com:/usr/obj/usr/src/sys/MYKERNEL
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD Athlon(TM) XP1600+ (1410.20-MHz 686-class
CPU)
Origin = "AuthenticAMD" Id = 0x662 Stepping = 2
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0480000<<b19>,AMIE,DSP,3DNow!>
real memory = 268353536 (262064K bytes)
config> di pcic0
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di ed0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory = 255860736 (249864K bytes)
Preloaded elf kernel "kernel" at 0xc0522000.
Preloaded userconfig_script "/boot/kernel.conf" at
0xc052209c.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 10 entries at 0xc00f1410
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=1106 device=b099)>
at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI model 5046 graphics accelerator> at 0.0 irq
11
pcm0: <CMedia CMI8738> port 0xb800-0xb8ff irq 10 at
device 5.0 on pci0
ahc0: <Adaptec aic7850 SCSI adapter> port
0xb400-0xb4ff mem 0xf2800000-0xf2800fff irq 11 at
device 13.0 on pci0
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
xl0: <3Com 3c905-TX Fast Etherlink XL> port
0xb000-0xb03f irq 5 at device 15.0 on pci0
xl0: Ethernet address: 00:a0:24:d1:7f:fb
miibus0: <MII bus> on xl0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX,
100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=1106 device=3074)>
at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 8233 ATA100 controller> port
0xa800-0xa80f irq 0 at device 17.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xa400-0xa41f
irq 9 at device 17.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: Hewlett-Packard OfficeJet V40, rev 1.10/1.00,
addr 2
uhci1: <VIA 83C572 USB controller> port 0xa000-0xa01f
irq 9 at device 17.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0x9800-0x981f
irq 9 at device 17.4 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00,
addr 1
uhub2: 2 ports with 2 removable, self powered
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xd0000-0xd3fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7
irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port
0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem
0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on
isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in
COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
unknown: <PNP0401> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> can't assign resources
unknown: <PNP0700> can't assign resources
unknown: <PNP0f13> can't assign resources
unknown: <PNP0c01> can't assign resources
unknown: <PNP0000> can't assign resources
unknown: <PNP0303> can't assign resources
ad0: 38166MB <WDC WD400BB-00CXA0> [77545/16/63] at
ata0-master UDMA100
ad2: 19092MB <WDC WD200BB-00CJA0> [38792/16/63] at
ata1-master UDMA100
ata1-slave: timeout waiting for cmd=ef s=00 e=00
acd0: CDROM <Pioneer CD-ROM ATAPI Model DR-A24X 0104>
at ata1-slave BIOSPIO
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 1 lun 0
sa0: <HP C1533A AN04> Removable Sequential Access
SCSI-2 device
sa0: 6.756MB/s transfers (6.756MHz, offset 15)
Mounting root from ufs:/dev/ad2s1a
ad2s1a: UDMA ICRC error reading fsbn 255 of 96-127
(ad2s1 bn 255; cn 0 tn 4 sn 3) retrying
ad2s1a: UDMA ICRC error reading fsbn 255 of 96-127
(ad2s1 bn 255; cn 0 tn 4 sn 3) retrying
ad2s1a: UDMA ICRC error reading fsbn 255 of 96-127
(ad2s1 bn 255; cn 0 tn 4 sn 3) retrying
ad2s1a: UDMA ICRC error reading fsbn 255 of 96-127
(ad2s1 bn 255; cn 0 tn 4 sn 3) falling back to PIO
mode
=====
--
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
William Blair Wagner : Education is not always knowing the answer
blairwag1965@yahoo.com : ..but rather knowing where to look for it!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020808051951.2394.qmail>