Date: Fri, 21 Jul 2000 20:13:45 -0700 From: "Joseph Stein" <joes@teleport.com> To: <freebsd-questions@freebsd.org> Subject: HELP! Old "super user" having problems with new modern computer :) [LONG] Message-ID: <005f01bff38a$da37f540$0100a8c0@wstein.com>
next in thread | raw e-mail | index | archive | help
Hello all, (Old and New :)
I have been away from the FreeBSD game for a little over a year and a half.
I am back now, and have recently tried to up the ante with myself.
I used to have an AMD 4x86-120 with 72mb of Ram. I finally gave up on
waiting a day and a half to "buildworld", and upgraded the whole machine to
an AMD K7-Athlon-600MHz with 128MB. Boy. Two hours, and the world is built
AND installed :)
But, I have a problem.
When the bootloader starts up, it starts booting properly, BUT, when it gets
to the point where it is "Mounting root from ufs:/dev/ad0s1a," it seems to
have a problem using WDMA2. I believe this stems from the fact that this
disk was
originally installed in the old 486 (that did not support DMA at all, that I
know of). The new disk was newfs'd in the same computer though, and I don't
know how to explain that it works :) (The old disk is ad0, the new disk is
ad1).
I have found all of the settings to set 'pio mode' once the system is going
to multi-user; but I can't find anything to force PIO mode on boot -- when
sometimes, it succeeds and produces like data to the data below, but more
often than not, locks up trying to reset the ata devices.
Any ideas, help, suggestions?
For the record, this is
FreeBSD shasta.wstein.com 4.1-RC FreeBSD 4.1-RC #0: Fri Jul 21 18:56:26 PDT
2000 root@shasta.wstein.com:/b/obj/usr/src/sys/SHASTA i386
and it was a fresh-cvsup as of about Thu Jul 20 20:00:00 PDT 2000.
(the 3.whatever-STABLE that was on the original disk booted just fine, BTW,
so it is something new in 4.0-STABLE/4.1-RC.)
Thanks in advance for any help,
joe
Here follows some verbose boot information:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RC #0: Fri Jul 21 18:56:26 PDT 2000
root@shasta.wstein.com:/b/obj/usr/src/sys/SHASTA
Calibrating clock(s) ... TSC clock: 598797642 Hz, i8254 clock: 1193104 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: AMD-K7(tm) Processor (598.84-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x612 Stepping = 2
Features=0x81f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,P
AT,MMX>
AMD Features=0xc0400000<AMIE,DSP,3DNow!>
Data TLB: 24 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way
associative
L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
real memory = 134152192 (131008K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009ffff, 651264 bytes (159 pages)
0x00353000 - 0x07fe7fff, 130633728 bytes (31893 pages)
avail memory = 127205376 (124224K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fb180
bios32: Entry = 0xfb5f0 (c00fb5f0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb620
pnpbios: Found PnP BIOS data at 0xc00fbfb0
pnpbios: Entry = f0000:bfe0 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f5fc0
Preloaded elf kernel "kernel" at 0xc033a000.
Preloaded elf module "splash_bmp.ko" at 0xc033a0a8.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
module_register_init: MOD_LOAD (splash_bmp, c03357d4, 0) error 2
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003840
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=70061022)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=70061022)
pcib0: <AMD-751 host to PCI bridge> on motherboard
found-> vendor=0x1022, dev=0x7006, revid=0x25
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d0000000, size 27
map[14]: type 1, range 32, base e0000000, size 12
found-> vendor=0x1022, dev=0x7007, revid=0x01
class=06-04-00, hdrtype=0x01, mfdev=1
subordinatebus=1 secondarybus=1
found-> vendor=0x1022, dev=0x7408, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1022, dev=0x7409, revid=0x03
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000f000, size 4
found-> vendor=0x1022, dev=0x740b, revid=0x03
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1022, dev=0x740c, revid=0x06
class=0c-03-10, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=5
map[10]: type 1, range 32, base e0001000, size 12
found-> vendor=0x10ec, dev=0x8139, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000e400, size 8
map[14]: type 1, range 32, base e0002000, size 8
found-> vendor=0x10ec, dev=0x8139, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000e800, size 8
map[14]: type 1, range 32, base e0003000, size 8
pci0: <PCI bus> on pcib0
pcib1: <AMD-751 PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x5333, dev=0x8a13, revid=0x02
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=12
map[10]: type 1, range 32, base d8000000, size 26
pci1: <PCI bus> on pcib1
pci1: <S3 Trio3D/2X graphics accelerator> (vendor=0x5333, dev=0x8a13) at 5.0
irq 12
isab0: <PCI to ISA bridge (vendor=1022 device=7408)> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 756 ATA66 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 status0=50 status1=50
ata0: mask=03 status0=52 status1=50
ata0: devices = 0x3
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=03 status0=20 status1=30
ata1: mask=03 status0=20 status1=30
ata1: devices = 0x0
ata1: probe allocation failed
chip1: <PCI to Other bridge (vendor=1022 device=740b)> at device 7.3 on pci0
ohci0: <AMD-756 USB Controller> mem 0xe0001000-0xe0001fff irq 5 at device
7.4 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AMD-756 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
rl0: <RealTek 8139 10/100BaseTX> port 0xe400-0xe4ff mem
0xe0002000-0xe00020ff irq 10 at device 10.0 on pci0
rl0: Ethernet address: 00:50:ba:85:e0:58
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: rl0 attached
rl1: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem
0xe0003000-0xe00030ff irq 11 at device 12.0 on pci0
rl1: Ethernet address: 00:50:ba:8b:22:65
miibus1: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus1
rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: rl1 attached
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=03 status0=20 status1=30
ata3: mask=03 status0=20 status1=30
ata3: devices = 0x0
ata3: probe allocation failed
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0067
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:ffffffff
kbdc: RESET_AUX return code:ffffffff
kbdc: RESET_AUX return code:ffffffff
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x11 0x11
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x1 0x9 0x9 0x9
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03a67f3f 0..934=935 cylinders, 0..127=128 heads, 1..63=63 sectors
1:020bfe3f 0..523=524 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: faith0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 684060, tty 63009a, net 670c9a
bpf: sl0 attached
IP packet filtering initialized, divert enabled, rule-based forwarding
disabled, default to accept, logging disabled
IP Filter: v3.4.8 initialized. Default = pass all, Logging = disabled
ata0-master: success setting up WDMA2 mode on AMD chip
ad0: <QUANTUM FIREBALL_TM3840A/A6B.2400> ATA-0 disk at ata0 as master
ad0: 3681MB (7539840 sectors), 7480 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, WDMA2
ad0: piomode=4 dmamode=2 udmamode=-1 cblid=0
Creating DISK ad0
Creating DISK wd0
ata0-slave: success setting up UDMA4 mode on AMD chip
ad1: <QUANTUM FIREBALL CR4.3A/A5U.1200> ATA-4 disk at ata0 as slave
ad1: 4110MB (8418816 sectors), 14848 cyls, 9 heads, 63 S/T, 512 B/S
ad1: 16 secs/int, 1 depth queue, UDMA66
ad1: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad1
Creating DISK wd1
Mounting root from ufs:/dev/ad0s1a
ad0: READ command timeout - resetting
ata0: resetting devices .. ata0: mask=03 status0=50 status1=50
ata0-master: success setting up WDMA2 mode on AMD chip
ata0-slave: success setting up UDMA4 mode on AMD chip
done
ad0: READ command timeout - resetting
ata0: resetting devices .. ata0: mask=03 status0=50 status1=50
ata0-master: success setting up WDMA2 mode on AMD chip
ata0-slave: success setting up UDMA4 mode on AMD chip
done
ad0: READ command timeout - resetting
ata0: resetting devices .. ata0: mask=03 status0=52 status1=50
ata0-master: success setting up WDMA2 mode on AMD chip
ata0-slave: success setting up UDMA4 mode on AMD chip
done
ad0: READ command timeout - resetting
ata0-master: WARNING: WAIT_READY active=ATA_ACTIVE_ATA
ata0-master: success setting up PIO4 mode on generic chip
ad0: trying fallback to PIO mode
ata0: resetting devices .. ata0: mask=03 status0=50 status1=50
ata0-master: success setting up PIO4 mode on generic chip
ata0-slave: success setting up UDMA4 mode on AMD chip
done
ad0s1: type 0xa5, start 0, end = 7539839, size 7539840
ad0s1: C/H/S end 469/84/63 (2516849) != end 7539839: invalid
start_init: trying /sbin/init
Linux-ELF exec handler installed
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?005f01bff38a$da37f540$0100a8c0>