Date: Sat, 18 Nov 2000 00:52:21 -0500 (EST) From: x@asdf.com To: freebsd-questions@freebsd.org Subject: after IDE Hard Drive install, netgear NIC card stopped being recognized Message-ID: <Pine.BSF.4.21.0011172251550.95972-100000@bellona.asdf.com>
next in thread | raw e-mail | index | archive | help
Hello
I have an ASUS P2L97-DS MB. It has on-board SCSI, and I have a 2 gig SCSI
drive in. I have an AGP cheap-o graphics card, and I picked up two Netgear
10/100 Mbps NIC cards Model: FA311. I booted off the IDE CD-ROM drive
using FreeBSD 4.1-R. It installed just fine, I logged in and for a few
weeks everything was fine. The NIC cards were detected at install time as
sis (this from an older email that I saved):
Network interface status:
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Coll
sis0 1500 <Link#1> 00:a0:cc:75:1f:46 1351 0 775 0 0
sis0 1500 015gra088/29 015gra091 1351 0 775 0 0
sis0 1500 fe80:1::2a0 fe80:1::2a0:ccff: 1351 0 775 0 0
sis1* 1500 <Link#2> 00:a0:cc:75:3b:e6 0 0 0 0 0
I didn't set up the 2nd NIC at that time with an IP address, since I
wanted to read up on setting up a firewall for my network at home. Anyway,
I picked up a 30 gig IBM DTLA-307030 IDE drive for the box, and proceeded
to install it. I kept the SCSI drive around for /var and a swap drive,
just because. Now, after I installed of the same CD, using the same
hardware and adding nothing other than the HD, FreeBSD won't recognize the
NIC cards. I get:
pci0: <unknown card> (vendor=0x100b, dev=0x0020) at 9.0 irq 5
pci0: <unknown card> (vendor=0x100b, dev=0x0020) at 10.0 irq 10
I've tried booting off the CD, booting with kernel.GENERIC, but I get the
same thing. I'll paste a dmesg.boot in verbose mode to the end of this
email.
I'm not sure why it all of a sudden doesn't notice the cards; I don't see
them officially supported in the handbook, but I've never had an issue
with Netgear cards in the past and it was working before. I've tried
resetting the BIOS by going in and reseting to defaults and then saving,
and also upgraded to the latest BIOS revision (thinking maybe adding the
IDE drive would screw up the IRQs or DMA or something). I've also taken
the IDE drive out, taken the NIC cards out, let the auto DMI on the
motherboard update, put the NICs in different slots, tried a PCI video
card instead of an AGP, and booted with no hard drives off the cd.
The chips on the NIC card say:
on card:
Netgear
FA311 REV-A1
on big chip in middle:
VS941AGC4
DP83815CVNG
on smaller chip towards RJ-45 jack:
DELTA
LF8221M0006
I also just now installed Win2000 Pro on the last half of the IDE drive (I
only partitioned 15 gigs for fbsd) and it recognized the NIC cards and I
was able to get out on the Net, though I had to use the disk included with
the NIC cards to get the right drivers. The disk does have Linux drivers,
but when I try to make install them I get a bunch of errors about Linux
directories not being there.
Any ideas? I'm stumped for right now, still searching through the mailing
lists ;-) Here is the dmesg, sorry if it makes this email huge but I
didn't know if attachments were OK on this list. This is booting with
kernel.GENERIC:
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000
jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC
Calibrating clock(s) ... TSC clock: 300768990 Hz, i8254 clock: 1193527 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x634 Stepping = 4
Features=0x80fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 234868736 (229364K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00426000 - 0x0dff4fff, 230486016 bytes (56271 pages)
avail memory = 224243712 (218988K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f9d00
bios32: Entry = 0xf0530 (c00f0530) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x730
pnpbios: Found PnP BIOS data at 0xc00fd130
pnpbios: Entry = f0000:d160 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 000f7ff0
Preloaded elf kernel "kernel.GENERIC" at 0xc040d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71808086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71808086)
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7180, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base e4000000, size 26
found-> vendor=0x8086, dev=0x7181, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000d800, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=255
map[20]: type 1, range 32, base 0000d400, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x01
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 0000e800, size 4
found-> vendor=0x9004, dev=0x8078, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000d000, size 8
map[14]: type 1, range 32, base db800000, size 12
found-> vendor=0x100b, dev=0x0020, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000b800, size 8
map[14]: type 1, range 32, base db000000, size 12
found-> vendor=0x100b, dev=0x0020, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base 0000b400, size 8
map[14]: type 1, range 32, base da800000, size 12
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443LX (440 LX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x5333, dev=0x8a13, revid=0x02
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base dc000000, size 26
pci1: <PCI bus> on pcib1
pci1: <S3 Trio3D/2X graphics accelerator> (vendor=0x5333, dev=0x8a13) at
0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xd800-0xd80f at device 4.1
on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd800
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd808
ata1: mask=01 status0=50 status1=ff
ata1: mask=01 status0=00 status1=ff
ata1: devices = 0x4
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd400-0xd41f at
device 4.2 on pci0
uhci0: Invalid irq 255
uhci0: Please switch on USB support and switch PNP-OS to 'No' in BIOS
device_probe_and_attach: uhci0 attach returned 6
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device 4.3 on pci0
ahc0: <Adaptec aic7880 Ultra SCSI adapter> port 0xd000-0xd0ff mem
0xdb800000-0xdb800fff irq 5 at device 6.0 on pci0
ahc0: Reading SEEPROM...done.
ahc0: Low byte termination Enabled
ahc0: High byte termination Enabled
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc0: Downloading Sequencer Program... 415 instructions downloaded
pci0: <unknown card> (vendor=0x100b, dev=0x0020) at 9.0 irq 5
pci0: <unknown card> (vendor=0x100b, dev=0x0020) at 10.0 irq 10
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:0106fe3f 0..262=263 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 68c040, tty 63101a, net 67101a
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
ata0-master: success setting up UDMA2 mode on PIIX4 chip
ad0: <IBM-DTLA-307030/TX4OA50C> ATA-5 disk at ata0 as master
ad0: 29314MB (60036480 sectors), 59560 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 32 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=3 dmamode=1 udmamode=-1 dmaflag=1
ata1-master: success setting up PIO3 mode on generic chip
acd0: <NEC CD-ROM DRIVE:282/3.05> CDROM drive at ata1 as master
acd0: read 1376KB/s (1376KB/s), 128KB buffer, PIO3
acd0: Reads: CD-DA
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ahc0: target 6 synchronous at 20.0MHz, offset = 0xf
Creating DISK da0
pass0 at ahc0 bus 0 target 6 lun 0
pass0: <IBM DCAS-32160 S65A> Fixed Direct Access SCSI-2 device
pass0: Serial Number F2788432
pass0: 20.000MB/s transfers (20.000MHz, offset 15)
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 30719807, size 30719745
ad0s1: C/H/S end 1023/55/63 (16438022) != end 30719807: invalid
ad0s2: type 0x7, start 30732345, end = 60018839, size 29286495
ad0s2: C/H/S start 1023/0/1 (16434495) != start 30732345: invalid
da0 at ahc0 bus 0 target 6 lun 0
da0: <IBM DCAS-32160 S65A> Fixed Direct Access SCSI-2 device
da0: Serial Number F2788432
da0: 20.000MB/s transfers (20.000MHz, offset 15)
da0: 2063MB (4226725 512 byte sectors: 255H 63S/T 263C)
start_init: trying /sbin/init
da0s1: type 0xa5, start 0, end = 4226724, size 4226725
da0s1: C/H/S end 263/25/55 (377519) != end 4226724: invalid
Any help is appreciated.
Thanks!
Dan
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0011172251550.95972-100000>