Date: Tue, 05 Feb 2002 05:46:48 -0600 From: Greg Panula <greg.panula@dolaninformation.com> To: freebsd-stable@freebsd.org Subject: SMP kernel & dc driver Message-ID: <3C5FC628.294C8A92@dolaninformation.com>
next in thread | raw e-mail | index | archive | help
Howdy,
I am experiencing watchdog timeouts and lack of network connectivity with
my dfe570tx nic when I have a SMP capable kernel loaded. When I use a
non-smp kernel, the nic behaves fine. Basically if I run a kernel that uses
both CPUs the dfe570tx(dc driver) is dead in the water & the on-board intel
nics(fxp driver) work fine. Use a kernel that only uses one CPU and I can
use both nics(dfe570tx and on-board intel nic).
I cvsup'd the source tree on 02/03/2002 (around 10am cst) and
built&installed a fresh world from that code, kernels included. Previously
the box was a clean install from a 4.4 CD. The non-smp kernel is the
GENERIC kernel. The smp kernel is GENERIC with smp uncommented, IPSEC
supported add(grep IPSEC LINT > dl360-smp) and the following lines commented
out:
cpu I386_CPU
cpu I486_CPU
options MATH_EMULATE
options INET6
Here are the dmesgs from boot-up:
SMP KERNEL
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #0: Mon Feb 4 15:22:50 CST 2002
root@:/usr/obj/usr/src/sys/dl360-smp
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1263.45-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 402636800 (393200K bytes)
avail memory = 386707456 (377644K bytes)
Changing APIC ID for IO APIC #0 from 0 to 8 on chip
Programming 35 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x00220011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc04a6000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
IOAPIC #0 intpin 19 -> irq 2
IOAPIC #0 intpin 21 -> irq 3
pci0: <PCI bus> on pcib0
ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem
0xc4000000-0xc4ffffff,0xc5000000-0xc5ffffff irq 2 at device 1.0 on pci0
ida0: drives=1 firm_rev=1.42
idad0: <Compaq Logical Drive> on ida0
idad0: 17359MB (35553120 sectors), blocksize=512
pci0: <ATI Mach64-GV graphics accelerator> at 3.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
pcib1: <PCI to PCI bridge (vendor=8086 device=0960)> at device 5.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GV graphics accelerator> at 0.0
pci0: <unknown card> (vendor=0x8086, dev=0x1960) at 5.1 irq 3
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2800-0x280f at device
15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
IOAPIC #0 intpin 17 -> irq 5
IOAPIC #0 intpin 24 -> irq 7
pci3: <PCI bus> on pcib3
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x4000-0x403f mem
0xc6d00000-0xc6dfffff,0xc6eff000-0xc6efffff irq 5 at device 4.0 on pci3
fxp0: Ethernet address 00:02:a5:8b:db:46
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0x4040-0x407f mem
0xc6b00000-0xc6bfffff,0xc6cff000-0xc6cfffff irq 7 at device 5.0 on pci3
fxp1: Ethernet address 00:02:a5:8b:db:45
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib2: <DEC 21152 PCI-PCI bridge> at device 6.0 on pci3
pci4: <PCI bus> on pcib2
dc0: <Intel 21143 10/100BaseTX> port 0x5000-0x507f mem 0xc6fffc00-0xc6ffffff
irq 11 at device 4.0 on pci4
dc0: Ethernet address: 00:80:c8:cf:b0:49
miibus2: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus2
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc1: <Intel 21143 10/100BaseTX> port 0x5080-0x50ff mem 0xc6fff800-0xc6fffbff
irq 11 at device 5.0 on pci4
dc1: Ethernet address: 00:80:c8:cf:b0:4a
miibus3: <MII bus> on dc1
ukphy1: <Generic IEEE 802.3u media interface> on miibus3
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc2: <Intel 21143 10/100BaseTX> port 0x5400-0x547f mem 0xc6fff400-0xc6fff7ff
irq 11 at device 6.0 on pci4
dc2: Ethernet address: 00:80:c8:cf:b0:4b
miibus4: <MII bus> on dc2
ukphy2: <Generic IEEE 802.3u media interface> on miibus4
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc3: <Intel 21143 10/100BaseTX> port 0x5480-0x54ff mem 0xc6fff000-0xc6fff3ff
irq 11 at device 7.0 on pci4
dc3: Ethernet address: 00:80:c8:cf:b0:4c
miibus5: <MII bus> on dc3
ukphy3: <Generic IEEE 802.3u media interface> on miibus5
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xe8000-0xedfff,0xee000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0x2
ppc0: parallel port not found.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin
2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
IPsec: Initialized Security Association Processing.
SMP: AP CPU #1 Launched!
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
acd0: CDROM <CD-224E> at ata1-master using PIO4
Mounting root from ufs:/dev/idad0s2a
NON-SMP KERNEL
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #0: Mon Feb 4 15:04:46 CST 2002
root@:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1263.45-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 402636800 (393200K bytes)
avail memory = 386785280 (377720K bytes)
Preloaded elf kernel "kernel" at 0xc0496000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ida0: <Compaq Integrated Array controller> port 0x2000-0x20ff mem
0xc4000000-0xc4ffffff,0xc5000000-0xc5ffffff irq 5 at device 1.0 on pci0
ida0: drives=1 firm_rev=1.42
idad0: <Compaq Logical Drive> on ida0
idad0: 17359MB (35553120 sectors), blocksize=512
pci0: <ATI Mach64-GV graphics accelerator> at 3.0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 4.0
pcib1: <PCI to PCI bridge (vendor=8086 device=0960)> at device 5.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GV graphics accelerator> at 0.0
pci0: <unknown card> (vendor=0x8086, dev=0x1960) at 5.1 irq 3
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 ATA33 controller> port 0x2800-0x280f at device
15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcib3: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x4000-0x403f mem
0xc6d00000-0xc6dfffff,0xc6eff000-0xc6efffff irq 7 at device 4.0 on pci3
fxp0: Ethernet address 00:02:a5:8b:db:46
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0x4040-0x407f mem
0xc6b00000-0xc6bfffff,0xc6cff000-0xc6cfffff irq 10 at device 5.0 on pci3
fxp1: Ethernet address 00:02:a5:8b:db:45
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib2: <DEC 21152 PCI-PCI bridge> at device 6.0 on pci3
pci4: <PCI bus> on pcib2
dc0: <Intel 21143 10/100BaseTX> port 0x5000-0x507f mem 0xc6fffc00-0xc6ffffff
irq 11 at device 4.0 on pci4
dc0: Ethernet address: 00:80:c8:cf:b0:49
miibus2: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus2
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc1: <Intel 21143 10/100BaseTX> port 0x5080-0x50ff mem 0xc6fff800-0xc6fffbff
irq 11 at device 5.0 on pci4
dc1: Ethernet address: 00:80:c8:cf:b0:4a
miibus3: <MII bus> on dc1
ukphy1: <Generic IEEE 802.3u media interface> on miibus3
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc2: <Intel 21143 10/100BaseTX> port 0x5400-0x547f mem 0xc6fff400-0xc6fff7ff
irq 11 at device 6.0 on pci4
dc2: Ethernet address: 00:80:c8:cf:b0:4b
miibus4: <MII bus> on dc2
ukphy2: <Generic IEEE 802.3u media interface> on miibus4
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc3: <Intel 21143 10/100BaseTX> port 0x5480-0x54ff mem 0xc6fff000-0xc6fff3ff
irq 11 at device 7.0 on pci4
dc3: Ethernet address: 00:80:c8:cf:b0:4c
miibus5: <MII bus> on dc3
ukphy3: <Generic IEEE 802.3u media interface> on miibus5
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0685 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xe8000-0xedfff,0xee000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0x2
ppc0: parallel port not found.
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
acd0: CDROM <CD-224E> at ata1-master using PIO4
Mounting root from ufs:/dev/idad0s2a
The hardware platform is a Compaq DL360.
I would really like to use both CPUs&nics at the same time. Any suggestions
or ideas?
Thanks,
Greg Panula
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3C5FC628.294C8A92>