Date: Fri, 20 Feb 2004 18:52:52 -0700 From: David Bear <David.Bear@asu.edu> To: freebsd-questions@freebsd.org Subject: problem with tape units Message-ID: <20040220185252.A8056@asu.edu>
next in thread | raw e-mail | index | archive | help
I recently replace an ait tape drive with another one of the same model,, a sony sdx 300. Now, when I try to do anything with /dev/sa0 like get status or erase, I get a ton of errors. Below is the output of dmesg from it. Do I need to remake the sa device? Don't know why things would be timing out. I have an active terminator on the unit.. it is an external tape unit, connected to an adaptec 29160 card (wide). It is the ONLY device on the scsi card and set at ID 10. I am using freebsd4.9. any advice would be appreciated (sa0:ahc1:0:10:0): SCB 0xe - timed out ahc1: Dumping Card State while idle, at SEQADDR 0x9 ACCUM =3D 0x4, SINDEX =3D 0xa7, DINDEX =3D 0x2b, ARG_2 =3D 0x3 HCNT =3D 0x0 SCBPTR =3D 0x0 SCSISEQ =3D 0x12, SBLKCTL =3D 0x6 DFCNTRL =3D 0x0, DFSTATUS =3D 0x89 LASTPHASE =3D 0x1, SCSISIGI =3D 0x0, SXFRCTL0 =3D 0x80 SSTAT0 =3D 0x0, SSTAT1 =3D 0x8 SCSIPHASE =3D 0x0 STACK =3D=3D 0x3, 0x175, 0x160, 0x0 SCB count =3D 20 Kernel NEXTQSCB =3D 0 Card NEXTQSCB =3D 0 QINFIFO entries:=20 Waiting Queue entries:=20 Disconnected Queue entries: 0:14=20 QOUTFIFO entries:=20 Sequencer Free SCB List: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20= 21 22 23 24 25 26 27 28 29 30 31=20 Sequencer SCB Info: 0(c 0x44, s 0xa7, l 0, t 0xe) 1(c 0x0, s 0xff, l 255, t= 0xff) 2(c 0x0, s 0xff, l 255, t 0xff) 3(c 0x0, s 0xff, l 255, t 0xff) 4(c = 0x0, s 0xff, l 255, t 0xff) 5(c 0x0, s 0xff, l 255, t 0xff) 6(c 0x0, s 0xff= , l 255, t 0xff) 7(c 0x0, s 0xff, l 255, t 0xff) 8(c 0x0, s 0xff, l 255, t = 0xff) 9(c 0x0, s 0xff, l 255, t 0xff) 10(c 0x0, s 0xff, l 255, t 0xff) 11(c= 0x0, s 0xff, l 255, t 0xff) 12(c 0x0, s 0xff, l 255, t 0xff) 13(c 0x0, s 0= xff, l 255, t 0xff) 14(c 0x0, s 0xff, l 255, t 0xff) 15(c 0x0, s 0xff, l 25= 5, t 0xff) 16(c 0x0, s 0xff, l 255, t 0xff) 17(c 0x0, s 0xff, l 255, t 0xff= ) 18(c 0x0, s 0xff, l 255, t 0xff) 19(c 0x0, s 0xff, l 255, t 0xff) 20(c 0x= 0, s 0xff, l 255, t 0xff) 21(c 0x0, s 0xff, l 255, t 0xff) 22(c 0x0, s 0xff= , l 255, t 0xff) 23(c 0x0, s 0xff, l 255, t 0xff) 24(c 0x0, s 0xff, l 255, = t 0xff) 25(c 0x0, s 0xff, l 255, t 0xff) 26(c 0x0, s 0xff, l 255, t 0xff) 2= 7(c 0x0, s 0xff, l 255, t 0xff) 28(c 0x0, s 0xff, l 255, t 0xff) 29(c 0x0, = s 0xff, l 255,=20 t 0xff) 30(c 0x0, s 0xff, l 255, t 0xff) 31(c 0x0, s 0xff, l 255, t 0xff)= =20 Pending list: 14(c 0x40, s 0xa7, l 0) Kernel Free SCB list: 15 16 17 18 19 1 2 3 4 5 6 7 8 9 13 12 11 10=20 Untagged Q(10): 14=20 sg[0] - Addr 0x41c5000 : Length 4096 sg[1] - Addr 0x3f26000 : Length 4096 (sa0:ahc1:0:10:0): Queuing a BDR SCB (sa0:ahc1:0:10:0): Bus Device Reset Message Sent (sa0:ahc1:0:10:0): no longer in timeout, status =3D 34b ahc1: Bus Device Reset on A:10. 1 SCBs aborted (sa0:ahc1:0:10:0): MODE SENSE(06). CDB: 1a 0 f 0 1c 0=20 (sa0:ahc1:0:10:0): error code 0 (sa0:ahc1:0:10:0): MODE SENSE(06). CDB: 1a 0 0 0 c 0=20 (sa0:ahc1:0:10:0): error code 0 (sa0:ahc1:0:10:0): MODE SENSE(06). CDB: 1a 0 0 0 c 0=20 (sa0:ahc1:0:10:0): error code 0 ----- End forwarded message ----- --=20 David Bear phone: 480-965-8257 fax: 480-965-9189 College of Public Programs/ASU Wilson Hall 232 Tempe, AZ 85287-0803 "Beware the IP portfolio, everyone will be suspect of trespassing"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040220185252.A8056>