Date: 02 Jun 2001 15:34:01 -0400 From: Allan Strand <stranda@cofc.edu> To: freebsd-questions@freebsd.org Subject: troubles with D-link dwl-650 wireless NIC Message-ID: <86itiek76e.fsf@linum.cofc.edu>
next in thread | raw e-mail | index | archive | help
Hi all, I have a desktop machine into which I am trying to install a D-link 650 wireless NIC. This is a PCMCIA card, so it is attached to the PCI bus via a PCI-PCMCIA bridge that D-link provides. The bridge is recognized. pccardd recognizes that a card exists in the slot. It also seems to find the appropriate entry in /etc/defaults/pccard.conf. The configuration always exits and complains that it cannot find the MAC address. I can use pccardc and examine the tuples stored in the CIS, so I know that some communication is occurring between card and bus. Below I have included output from dmesg, the dumpcis from pccardc, and the entry in my version of pccard.conf. The system is a K-6 p450 running a stable 4.x cvsupped on 6/1/01. Can anyone shed some light? dmesg output-> =============================================================== Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.3-STABLE #1: Fri Jun 1 16:28:39 EDT 2001 root@linum.cofc.edu:/usr/obj/usr/src/sys/LINUM40 Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 501137426 Hz CPU: AMD-K6(tm) 3D processor (501.14-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> AMD Features=0x80000800<SYSCALL,3DNow!> real memory = 134201344 (131056K bytes) avail memory = 127164416 (124184K bytes) Preloaded elf kernel "kernel" at 0xc0375000. K6-family MTRR support enabled (2 registers) md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <AcerLabs M1541 (Aladdin-V) PCI host bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <AcerLabs M5243 PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <ATI Mach64-GB graphics accelerator> at 0.0 irq 11 chip1: <AcerLabs M15x3 Power Management Unit> at device 3.0 on pci0 isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xb800-0xb83f irq 5 at device 10.0 on pci0 xl0: Ethernet address: 00:10:4b:95:5d:16 miibus0: <MII bus> on xl0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pcic-pci0: <Ricoh RL5C475 PCI-CardBus Bridge> irq 12 at device 11.0 on pci0 atapci0: <AcerLabs Aladdin ATA33 controller> port 0xb400-0xb40f irq 0 at device 15.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> pcic0: <Intel i82365> at port 0x3e0 iomem 0xd0000 irq 10 on isa0 pcic0: management irq 10 pccard0: <PC Card bus -- kludge version> on pcic0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/7 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sbc0: <Creative ViBRA16C> at port 0x220-0x22f,0x300-0x301,0x388-0x38b irq 9 drq 1,5 on isa0 pcm0: <SB16 DSP 4.13> on sbc0 unknown: <PNP0401> can't assign resources unknown: <PNP0501> can't assign resources unknown: <PNP0501> can't assign resources unknown: <PNP0700> can't assign resources unknown: <PNP0000> can't assign resources unknown: <PNP0303> can't assign resources ata0-master: DMA limited to UDMA33, non-ATA66 compliant cable ad0: 8056MB <ST38421A> [16368/16/63] at ata0-master UDMA33 pccard: card inserted, slot 0 ad1: 9671MB <WDC AC310100B> [19650/16/63] at ata0-slave UDMA33 no devsw (majdev=0 bootdev=0xa0200000) Mounting root from ufs:/dev/ad0s1a ad1: UDMA ICRC error reading fsbn 0 (ad1 bn 0; cn 0 tn 0 sn 0) retrying ad1: UDMA ICRC error reading fsbn 0 (ad1 bn 0; cn 0 tn 0 sn 0) retrying ad1: UDMA ICRC error reading fsbn 0 (ad1 bn 0; cn 0 tn 0 sn 0) retrying ad1: UDMA ICRC error reading fsbn 0 (ad1 bn 0; cn 0 tn 0 sn 0) falling back to PIO mode IP packet filtering initialized, divert disabled, rule-based forwarding disabled, default to deny, logging disabled wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 11 slot 0 on pccard0 wi0: mac read failed 5 device_probe_and_attach: wi0 attach returned 5 ================================================ pccardc output-> ================================================ Configuration data for card in slot 0 Tuple #1, code = 0x1 (Common memory descriptor), length = 3 000: 00 00 ff Common memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = 512b, 1 units Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4 000: 67 5a 08 ff Attribute memory device information: Device number 1, type SRAM, WPS = OFF Speed = 5.0 x 100 ns, Memory block size = 512b, 2 units Tuple #3, code = 0x1d (Other conditions for attribute memory), length = 5 000: 03 67 5a 08 ff (MWAIT) (3V card) Tuple #4, code = 0x15 (Version 1 info), length = 80 000: 05 00 44 00 4c 69 6e 6b 20 44 57 4c 2d 36 35 30 010: 20 31 31 4d 62 70 73 20 57 4c 41 4e 20 43 61 72 020: 64 00 56 65 72 73 69 6f 6e 20 30 31 2e 30 32 00 030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff Version = 5.0, Manuf = [D], card vers = [Link DWL-650 11Mbps WLAN Card] Addit. info = [Version 01.02],[] Tuple #5, code = 0x20 (Manufacturer ID), length = 4 000: 56 01 02 00 PCMCIA ID = 0x156, OEM ID = 0x2 Tuple #6, code = 0x21 (Functional ID), length = 2 000: 06 00 Network/LAN adapter Tuple #7, code = 0x22 (Functional EXT), length = 2 000: 01 07 Network technology: Wireless Tuple #8, code = 0x22 (Functional EXT), length = 5 000: 02 40 42 0f 00 Network speed: 1 Mb/sec Tuple #9, code = 0x22 (Functional EXT), length = 5 000: 02 80 84 1e 00 Network speed: 2 Mb/sec Tuple #10, code = 0x22 (Functional EXT), length = 5 000: 02 60 ec 53 00 Network speed: 5 Mb/sec Tuple #11, code = 0x22 (Functional EXT), length = 5 000: 02 c0 d8 a7 00 Network speed: 11 Mb/sec Tuple #12, code = 0x22 (Functional EXT), length = 2 000: 03 07 Network media: 2.4 GHz Tuple #13, code = 0x22 (Functional EXT), length = 8 000: 04 06 00 05 5d f1 26 ac Network node ID: 00 05 5d f1 26 ac Tuple #14, code = 0x22 (Functional EXT), length = 2 000: 05 01 Network connector: closed connector standard Tuple #15, code = 0x1a (Configuration map), length = 7 000: 03 01 e0 03 00 00 01 Reg len = 4, config register addr = 0x3e0, last config = 0x1 Registers: X------- Tuple #16, code = 0x1b (Configuration entry), length = 16 000: c1 01 19 77 b5 1e 35 b5 3c 36 36 05 46 7f ff ff Config index = 0x1(default) Interface byte = 0x1 (I/O) Vcc pwr: Nominal operating supply voltage: 3 x 1V, ext = 0x1e Minimum operating supply voltage: 3 x 1V Maximum operating supply voltage: 3 x 1V, ext = 0x3c Max current average over 1 second: 3 x 100mA Max current average over 10 ms: 3 x 100mA Power down supply current: 1 x 10mA Card decodes 6 address lines, limited 8/16 Bit I/O IRQ modes: Level, Pulse IRQs: NMI IOCK BERR VEND 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Tuple #17, code = 0xff (Terminator), length = 0 1 slots found ======================================================= entry from pccard.conf -> ======================================================== # D Link DWL-650 11Mbps WLAN Card card "D" "Link DWL-650 11Mbps WLAN Card" config auto "wi" ? 0x10000 insert /etc/pccard_ether $device start remove /etc/pccard_ether $device stop ======================================================= Thanks, a. -- Allan To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?86itiek76e.fsf>