Date: Wed, 23 Apr 2003 11:59:39 -0700 From: "jeev" <jeev@boldinternet.net> To: <freebsd-scsi@freebsd.org> Subject: Issues with SuperMicro SuperServer 6011D System. Message-ID: <000001c309ca$7e1d9ea0$0200a8c0@mainframe>
next in thread | raw e-mail | index | archive | help
Hey guys, I've got a bunch of these: http://www.supermicro.com/PRODUCT/SUPERServer/SuperServer6011D.htm I currently am trying to get 2 of them working, I've tested them all = though. I have put 4.7 4.8 5.0 and upgraded and im still having issues. -- DMESG OUTPUT -- Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights = reserved. FreeBSD 5.0-RELEASE-p7 #0: Wed Apr 23 00:17:46 PDT 2003 root@ded16.bphosting.com:/usr/obj/usr/src/sys/jeev Preloaded elf kernel "/boot/kernel/kernel" at 0xc0660000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06600a8. Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (1266.07-MHz 686-class CPU) Origin =3D "GenuineIntel" Id =3D 0x6b1 Stepping =3D 1 =20 Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE= ,MCA, CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory =3D 1610547200 (1535 MB) avail memory =3D 1559953408 (1487 MB) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000 pnpbios: Bad PnP BIOS data checksum Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <VIA694 AWRDACPI> on motherboard ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 Using $PIR table, 7 entries at 0xc00fdf00 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 IOAPIC #0 intpin 12 -> irq 2 IOAPIC #0 intpin 10 -> irq 5 IOAPIC #0 intpin 11 -> irq 10 IOAPIC #0 intpin 5 -> irq 11 agp0: <VIA Generic host to PCI bridge> mem 0xf0000000-0xf3ffffff at = device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xd000-0xd03f mem 0xf8000000-0xf80fffff,0xf8203000-0xf8203fff irq 2 at device 10.0 on pci0 fxp0: Ethernet address 00:30:48:24:7a:df inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd400-0xd4ff mem 0xf8200000-0xf8200fff irq 5 at device 11.0 on pci0 aic7899: Ultra160 Wide Channel A, SCSI Id=3D7, 32/253 SCBs ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xd800-0xd8ff mem 0xf8201000-0xf8201fff irq 10 at device 11.1 on pci0 aic7899: Ultra160 Wide Channel B, SCSI Id=3D7, 32/253 SCBs fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xdc00-0xdc3f mem 0xf8100000-0xf81fffff,0xf8202000-0xf8202fff irq 11 at device 12.0 on = pci0 fxp1: Ethernet address 00:30:48:24:7a:e0 inphy1: <i82555 10/100 media interface> on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 8233 ATA100 controller> port 0xe000-0xe00f at device 17.1 = on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <serial bus, USB> at device 17.2 (no driver attached) pci0: <serial bus, USB> at device 17.3 (no driver attached) pci0: <serial bus, USB> at device 17.4 (no driver attached) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=3D0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on = isa0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Timecounters tick every 10.000 msec acpi_cpu: CPU throttling enabled, 2 steps from 100% to 50.0% acd0: CDROM <MATSHITA CR-177> at ata0-master PIO4 Waiting 15 seconds for SCSI devices to settle da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST336607LC 0004> Fixed Direct Access SCSI-3 device=20 da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged = Queueing Enabled da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/da0s1a -- DMESG -- this server is currently have major problems. First I was coming up = with. These were some of the errors I grabbed. sg[0] - Addr 0x14cd3000 : Length 2048 (da0:ahc0:0:0:0): no longer in timeout, status =3D 34b ahc0: Issued Channel A Bus Reset. 64 SCBs aborted spec_getpages:(#da/0x20000) I/O read failure: (error=3D5) bp 0xdb63d774 = vp 0xf5ad4ec0 size: 65536, resid: 65536, a_count: 65536, valid: 0x0 nread: 0, reqpage: 0, pindex: 0, pcount: 16 spec_getpages:(#da/0x20000) I/O read failure: (error=3D5) bp 0xdb63d390 = vp 0xf5ad4ec0 size: 65536, resid: 65536, a_count: 65536, valid: 0x0 nread: 0, reqpage: 0, pindex: 0, pcount: 16 spec_getpages:(#da/0x20000) I/O read failure: (error=3D5) bp 0xdb63d4dc = vp 0xf5ad4ec0 size: 20480, resid: 20480, a_count: 20480, valid: 0x0 nread: 0, reqpage: 0, pindex: 117, pcount: 5 vm_fault: pager read error, pid 516 (sshd) pid 516 (sshd), uid 22: exited on signal 11 spec_getpages:(#da/0x20000) I/O read failure: (error=3D5) bp 0xdb63d628 = vp 0xf5ad4ec0 size: 12800, resid: 12800, a_count: 12540, valid: 0x0 nread: 0, reqpage: 0, pindex: 0, pcount: 4 I especially got these lately. Not the top one. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. ahc0: Timedout SCB already complete. Interrupts may not be functioning. --- some of these -- 7 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 8 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 9 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 10 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]=20 SCB_LUN[0x0] SCB_TAG[0xff]=20 12 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 13 SCB_CONTROL[0x62]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]=20 SCB_TAG[0x72]=20 14 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 15 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 16 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 17 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 18 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 19 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 20 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 21 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]=20 22 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff] these are just snippets by the way. I am not sure what to do. I have looked at the supermicro page and found this. http://www.supermicro.com/TECHSUPPORT/FAQs/SCSI_FAQ.htm Questions: New system BIOS with SCSI BIOS 3.10S2 causing LINUX = installation hang at the blue screen with aic7xx....or SCSI multifunction=20 =20 Answer : Download this SEEPROM from here and follow the steps to reload = SCSI EEPROM to default if using older SCSI bios and upgrade to SCSI BIOS = 3.10S2 After having the guy at the datacenter put it on, it was no use. = Reboots usually take about 10-20 minutes, usually goes to FSCK, not sure how it breaks. He tells me they hang at: da0 at ahc0 bus 0 target 0 lun0 da0: <Seagate ST336607lc 0004> Fixed direct access SCSI -3 device da0: 160MB/s tranfers (80mhz, offset 63, 16 bit), tagging queueing = enabled da0: 35993 mb 971687372 512 byte sectors: 255h 63s/t 4462c) anybody have a workaround? Fix for this issue? If a developer would like = to get access to the box, I may be fine with that if they could create a = patch for the freebsd community, please notify me. Thanks. j
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?000001c309ca$7e1d9ea0$0200a8c0>