Date: Sat, 1 Jan 2005 15:20:54 -0500 From: Louis LeBlanc <FreeBSD@keyslapper.org> To: freebsd-questions@FreeBSD.org Subject: Re: Problems with digital camera Message-ID: <20050101202054.GC45452@keyslapper.org> In-Reply-To: <1104606089.874.1.camel@localhost> References: <1104600165.85905.2.camel@localhost> <20050101175305.GA45452@keyslapper.org> <1104603191.85905.5.camel@localhost> <20050101184340.GB45452@keyslapper.org> <1104606089.874.1.camel@localhost>
next in thread | previous in thread | raw e-mail | index | archive | help
On 01/01/05 02:01 PM, Trey Sizemore sat at the `puter and typed: > On Sat, 2005-01-01 at 13:43 -0500, Louis LeBlanc wrote: > > <SNIP> > > > > No, my reader has to be plugged in at boot, but inserting the card > > works on the fly. Your device may be different, but mine has always > > been /dev/da0s1 for the card itself. > > > > The /dev partition is pretty manageable in 5.3, so you might try an > > ls /dev > > and look for /dev/da0*. It might just jump out at you. I do an ls > > before inserting the card, and I see da0, but not da0s1. After > > inserting the card, da0s1 is there. Sometimes it's instantaneous, > > other times it takes a couple attempts to mount, but it works. > > > > Perhaps someone else on the list will know how to get the reader > > detected on the fly without a reboot, or perhaps the command to check > > the reader for an inserted card? > > > > I had thought camcontrol was it, but it doesn't seem to recognize that > > the card was removed. > > > > Lou > > Well, I've removed the entries in /boot/loader.conf (seemed redundant), > connected the SanDisk with card to the desktop, and rebooted. Here is > the output of dmesg (I also have a Epson Stylus C84 connected to the USB > hub and it doesn't appear to be detected either): > > > Copyright (c) 1992-2004 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.3-RELEASE #0: Fri Nov 5 04:19:18 UTC 2004 > root@harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.12-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 > Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXS > R,SSE,SSE2,SS,HTT,TM,PBE> > real memory = 536805376 (511 MB) > avail memory = 515616768 (491 MB) > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <AMIINT VIA_P6> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <VIA Generic host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > pcm0: <Creative EMU10K1> port 0xe800-0xe81f irq 11 at device 9.0 on pci0 > pcm0: <SigmaTel STAC9708/11 AC97 Codec> > fwohci0: <NEC uPD72873> mem 0xdffff000-0xdfffffff irq 11 at device 10.0 on pci0 > fwohci0: OHCI version 1.10 (ROM=1) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 00:00:4c:02:00:00:00:90 > fwohci0: Phy 1394a available S400, 2 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:00:4c:00:00:90 > fwe0: Ethernet address: 02:00:4c:00:00:90 > fwe0: if_start running deferred for Giant > sbp0: <SBP-2/SCSI over FireWire> on firewire0 > fwohci0: Initiate bus reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > uhci0: <VIA 83C572 USB controller> port 0xdc00-0xdc1f irq 5 at device 16.0 on pci0 > uhci0: [GIANT-LOCKED] > usb0: <VIA 83C572 USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 11 at device 16.1 on pci0 > uhci1: [GIANT-LOCKED] > usb1: <VIA 83C572 USB controller> on uhci1 > usb1: USB revision 1.0 > uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhci2: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 11 at device 16.2 on pci0 > uhci2: [GIANT-LOCKED] > usb2: <VIA 83C572 USB controller> on uhci2 > usb2: USB revision 1.0 > uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > pci0: <serial bus, USB> at device 16.3 (no driver attached) > isab0: <PCI-ISA bridge> at device 17.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <VIA 8235 UDMA133 controller> port 0xfc00-0xfc0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 17.1 on p > ci0 > ata0: channel #0 on atapci0 > ata1: channel #1 on atapci0 > vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xd800-0xd8ff mem 0xdfffee00-0xdfffeeff irq 5 at device 18.0 on pci0 > miibus0: <MII bus> on vr0 > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > vr0: Ethernet address: 00:0a:e6:6e:73:95 > acpi_button1: <Sleep Button> on acpi0 > fdc0: <floppy drive controller> port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3 irq 6 drq 2 on acpi0 > fdc0: [FAST] > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model IntelliMouse Explorer, device ID 4 > orm0: <ISA Option ROMs> at iomem 0xcf000-0xd2fff,0xc0000-0xcefff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 2800120244 Hz quality 800 > Timecounters tick every 10.000 msec > acpi_cpu: throttling enabled, 16 steps (100% to 6.2%), currently 100.0% > ad0: 78533MB <HDS722580VLAT20/V32OA60A> [159560/16/63] at ata0-master UDMA100 > acd0: DVDROM <SONY DVD-ROM DDU1612/DYS3> at ata1-master UDMA33 > acd1: CDRW <SONY CD-RW CRX230E/QYS1> at ata1-slave UDMA33 > Mounting root from ufs:/dev/ad0s1a > ________________________________________________________________ > > > Hmmmm.....ideas? That's strange. Did you have the umass device detected before removing the loader.conf entries? I don't have any usb related entries in loader.conf myself, so I don't see why you'd have trouble. What about the da device in your kernel config? I imagine you do have it since umass requires it . . . This is what I see in my dmesg: usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered umass0: SanDisk Corporation ImageMate CompactFlash USB, rev 1.10/0.09, addr 2 umass0: Get Max Lun not supported (STALLED) BTW, I never bothered to keep a card in the reader when booting. It's always been sufficient to keep the reader itself plugged in. What model is your reader? UMASS(4) lists a few that are explicitly supported, and mine is in the list; is yours? Sorry I can't help with the Epson. I stick to network printers when possible. Much less hassle. Lou -- Louis LeBlanc FreeBSD@keyslapper.org Fully Funded Hobbyist, KeySlapper Extrordinaire :) http://www.keyslapper.org ԿԬ Mathematicians are like Frenchmen: whatever you say to them they translate into their own language and forthwith it is something entirely different. -- Johann Wolfgang von Goethe
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050101202054.GC45452>