Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 28 May 1998 14:24:41 -0300 (EST)
From:      Luiz de Barros <luiz@nlink.com.br>
To:        Dennis <dennis@etinc.com>
Cc:        isp@FreeBSD.ORG, support@etinc.com, hardware@FreeBSD.ORG, hackers@FreeBSD.ORG
Subject:   Re: Cabling problems with etinc?
Message-ID:  <Pine.BSF.3.96.980528142254.7871C-100000@mirage.nlink.com.br>
In-Reply-To: <199805281525.LAA02507@etinc.com>

next in thread | previous in thread | raw e-mail | index | archive | help
I have everything working ok at 64Kbps on other connection and a Cyclades
connected to a Cisco on the other side at 256Kbps. I would like to connect
Etinc instead of cyclades here and it does not work.

Luiz


On Thu, 28 May 1998, Dennis wrote:

> At 09:34 AM 5/28/98 -0300, Luiz de Barros wrote:
> >Dear ALL,
> >
> >We purchased an Etinc 5025PQ PCI quad syncronous E1/T1/Fractional card and
> >are havind a few problems putting it to work with more than 64Kbps.
> >We have a 256Kbps fractional E1 link provided by the TELCO via an HDSL
> >Termination Unit and a G.703 to V.35 E1 converter. 
> 
> You say "greater than 64kbs...does that imply that you have it working at
> lower
> speeds or on some other connection? If so, there is no difference for the
> higher
> speed...you should use EXACTLY the same settings. the board uses the same 
> setting @ 64kbs and 2Mbs.
> >
> >We would like to make a FreeBSD router, connecting our various networks
> >and holding our connection to internet.
> >
> >The whole setup works fine with a cisco on the other side and IBM, Cisco
> >and Cyclades routers here at our ISP (Same CSU/DSU cable, connecting the
> >V.35 cable with the V.35 DTE cable from the router ). Etinc keeps saying
> >it is a clable problem, CSU/DSU problem, but how does it work with any
> >router?
> >
> >I configured etinc port to PPP, HDLC, internal, external clock, changed
> >ifconfig parameters according to the manual and i am not being able to put
> >the link up and IP packets going from one side to the other at 256Kbps.
> >
> >I purchased etinc because of good recomendations here on the list but as i
> >could see, the support from etinc is not as good as it should be.  Did
> >anybody already experienced any similar situation? Do i need to change
> >etinc's cable?  Does anybody know of any other card that can work in this
> >situation?
> >
> >I have heard of many other choices of Sync cards and maybe next time i
> >will use another card, that can give me support to work with more than
> >64Kbps. I used to recomend etinc to my friends because of its support to
> >FreeBSD, a Robust system with full support from the developers, etc but
> >now i am quite disappointed with etinc's support.
> >
> >Luiz
> >
> >
> >
> >
> >
> >
> >To Unsubscribe: send mail to majordomo@FreeBSD.org
> >with "unsubscribe freebsd-hackers" in the body of the message
> > 
> 


To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.980528142254.7871C-100000>