Date: Mon, 26 Jan 2004 07:58:38 +0200 From: "Atte Peltomaki" <koston@iki.fi> To: freebsd-current@freebsd.org Subject: Re: 5.2 on DELL m/c's Message-ID: <20040126055838.GA17125@naama.kameli.org> In-Reply-To: <136A7C767A0679488C4642731C2186E00262D5@blrx2kmbgl301.blr.amer.dell.com> References: <136A7C767A0679488C4642731C2186E00262D5@blrx2kmbgl301.blr.amer.dell.com>
next in thread | previous in thread | raw e-mail | index | archive | help
> I had installed 5.2 Release on couple of Dell machines. > It works fine on all the systems. (but some dhclient error messages > thrown on console often). > > In older machines (like PE4300) it works only if we disabled ACPI. > But in new machines (PE1750, PE1650) it works fine by default(with > ACPI). I did a fresh 5.2 install to Dell Precision 420 using 5.1 CD and ftp install, kernel panics at first boot after installation. With or without ACPI. Says it's waiting 15 seconds for SCSI devices for settle, actually takes about 2 minutes to come up with a memory dump plus something about interrupts looping. I can reproduce the error and post more relevant info if this is yet unsolved issue, now attached is a dmesg from the same box with 4.9 installed for teh hw specs. Atte Peltomaki http://kameli.org Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.9-RELEASE #0: Fri Jan 23 14:24:50 GMT 2004 root@norsu.kameli.org:/usr/src/sys/compile/NORSU Timecounter "i8254" frequency 1193182 Hz CPU: Intel Pentium III (797.97-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 536469504 (523896K bytes) avail memory = 516251648 (504152K bytes) Changing APIC ID for IO APIC #0 from 0 to 2 on chip Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00170020, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc0591000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 12 entries at 0xc00fbb20 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard IOAPIC #0 intpin 19 -> irq 2 IOAPIC #0 intpin 17 -> irq 13 pci0: <PCI bus> on pcib0 agp0: <Intel 82840 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0 pcib1: <PCI to PCI bridge (vendor=8086 device=1a23)> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <Matrox MGA G400 AGP graphics accelerator> at 0.0 irq 16 pcib2: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0 IOAPIC #0 intpin 18 -> irq 17 pci2: <PCI bus> on pcib2 xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec80-0xecff mem 0xf8fffc00-0xf8fffc7f irq 16 at device 4.0 on pci2 xl0: Ethernet address: 00:b0:d0:22:26:34 miibus0: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto csa0: <CS4280/CS4614/CS4622/CS4624/CS4630> mem 0xf8e00000-0xf8efffff,0xf8ffe000-0xf8ffefff irq 17 at device 6.0 on pci2 csa: card is Unknown/invalid SSID (CS4614) pcm0: <CS461x PCM Audio> on csa0 pcm0: <Cirrus Logic CS4297A AC97 Codec> pcib3: <DEC 21152 PCI-PCI bridge> at device 14.0 on pci2 pci3: <PCI bus> on pcib3 ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xfc00-0xfcff mem 0xfafff000-0xfaffffff irq 17 at device 10.0 on pci3 aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xf800-0xf8ff mem 0xfaffe000-0xfaffefff irq 2 at device 10.1 on pci3 aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH ATA66 controller> at device 31.1 on pci0 atapci0: ATA channel disabled by BIOS uhci0: <Intel 82801AA (ICH) USB controller> port 0xff80-0xff9f irq 2 at device 31.2 on pci0 usb0: <Intel 82801AA (ICH) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 13 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcdfff,0xce000-0xcffff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata1 at port 0x170-0x177,0x376 irq 15 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Waiting 15 seconds for SCSI devices to settle SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/da0s1a da0 at ahc0 bus 0 target 4 lun 0 da0: <IBM DDYS-T18350N S93E> Fixed Direct Access SCSI-3 device da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) cd0 at ahc1 bus 0 target 5 lun 0 cd0: <NEC CD-ROM DRIVE:466 1.06> Removable CD-ROM SCSI-2 device cd0: 20.000MB/s transfers (20.000MHz, offset 16) cd0: Attempt to query device size failed: NOT READY, Medium not present
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040126055838.GA17125>