Date: Mon, 07 May 2007 15:50:02 +0200 From: ronan <ron@artful.net> To: freebsd-sparc64@freebsd.org Subject: [sun] Booting problem with Sun Enterprise 220R Message-ID: <463F2E8A.5080204@artful.net>
next in thread | raw e-mail | index | archive | help
Hi all, I am trying to install from 6.2-STABLE-200704-sparc64-bootonly.iso <ftp://ftp.freebsd.org/pub/FreeBSD/snapshots/200704/6.2-STABLE-200704-sparc64-bootonly.iso>; (it is the same from the 7.0 CURRENT snapshot) But I cant, it crash during booting the kernel. Here is the boot log : ------------------------------------------------------------------------- Ethernet address 8:0:20:xx:xx:xx, Host ID: 80c823eb. Rebooting with command: boot /pci@1f,4000/scsi@3/disk@6,0:f Boot device: /pci@1f,4000/scsi@3/disk@6,0:f File and args: >> FreeBSD/sparc64 boot block Boot path: /pci@1f,4000/scsi@3/disk@6,0:f Boot loader: /boot/loader Consoles: Open Firmware console Boot path set to /pci@1f,4000/scsi@3/disk@6,0:a FreeBSD/sparc64 bootstrap loader, Revision 1.0 (root@edmunds.cse.buffalo.edu, Mon Apr 2 00:37:48 UTC 2007) bootpath="/pci@1f,4000/scsi@3/disk@6,0:a" Loading /boot/defaults/loader.conf /boot/kernel/kernel data=0x56f408+0x5bfa8 syms=[0x8+0x6d7b8+0x8+0x5b032] - Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... nothing to autoload yet. jumping to kernel entry at 0xc0060000. stray vector interrupt 2029 Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.2-STABLE-200704 #0: Mon Apr 2 16:12:13 UTC 2007 root@edmunds.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC real memory = 2147483648 (2048 MB) avail memory = 2063147008 (1967 MB) cpu0: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU) cpu1: Sun Microsystems UltraSparc-II Processor (450.05 MHz CPU) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, REGOPS_FUNC) nexus0: <Open Firmware Nexus device> pcib0: <U2P UPA-PCI bridge> on nexus0 pcib0: Psycho, impl 0, version 4, ign 0x7c0, bus B pcib0: [FAST] pcib0: [FAST] pcib0: [GIANT-LOCKED] pcib0: [GIANT-LOCKED] pcib0: [FAST] initializing counter-timer Timecounter "counter-timer" frequency 1000000 Hz quality 100 pcib0 dvma: DVMA map: 0xfc000000 to 0xffffffff pci0: <OFW PCI bus> on pcib0 ebus0: <PCI-EBus2 bridge> mem 0x70000000-0x70ffffff,0x71000000-0x717fffff at device 1.0 on pci0 auxio0: <Sun Auxiliary I/O> addr 0x1400726000-0x1400726003,0x1400728000-0x1400728003,0x140072a000-0x140072a003,0x140072c000-0x140072c003,0x140072f000-0x140072f003 on ebus0 ebus0: <power> addr 0x1400724000-0x1400724003 (no driver attached) ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached) ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver attached) puc0: <Siemens SAB 82532 dual channel SCC> addr 0x1400400000-0x140040007f irq 43 on ebus0 uart0: <SAB 82532 v3.2, channel A> on puc0 uart0: CTS oflow uart0: console (9600,n,8,1) uart1: <SAB 82532 v3.2, channel B> on puc0 uart1: CTS oflow uart2: <16550 or compatible> addr 0x14003083f8-0x14003083ff irq 41 on ebus0 uart2: keyboard (1200,n,8,1) uart2: keyboard not present uart3: <16550 or compatible> addr 0x14003062f8-0x14003062ff irq 42 on ebus0 ebus0: <ecpp> addr 0x14003043bc-0x14003043cb,0x1400300398-0x1400300399,0x1400700000-0x140070000f irq 34 (no driver attached) ebus0: <fdthree> addr 0x14003023f0-0x14003023f7,0x1400706000-0x140070600f,0x1400720000-0x1400720003 irq 39 (no driver attached) eeprom0: <EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0 eeprom0: model mk48t59 eeprom0: hostid 80c823eb ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no driver attached) hme0: <Sun HME 10/100 Ethernet> mem 0x500000-0x507fff at device 1.1 on pci0 miibus0: <MII bus> on hme0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto hme0: Ethernet address: 08:00:20:c8:23:eb sym0: <875> port 0x2000-0x20ff mem 0x508000-0x5080ff,0x50a000-0x50afff at device 3.0 on pci0 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: [GIANT-LOCKED] sym1: <875> port 0x2400-0x24ff mem 0x50c000-0x50c0ff,0x50e000-0x50efff at device 3.1 on pci0 sym1: No NVRAM, ID 7, Fast-20, SE, parity checking sym1: [GIANT-LOCKED] pci0: <serial bus, Fibre Channel> at device 2.0 (no driver attached) pcib1: <OFW PCI-PCI bridge> at device 4.0 on pci0 pci1: <OFW PCI bus> on pcib1 isp0: <Qlogic ISP 10160 PCI SCSI Adapter> port 0x1000-0x10ff mem 0x100000-0x100fff at device 4.0 on pci1 isp0: [GIANT-LOCKED] panic: trap: data access error cpuid = 0 Uptime: 1s Automatic reboot in 15 seconds - press a key on the console to abort ------------------------------------------------------------------------- Is there any solution ? Is it a compatibility problem with the Qlogic ISP 10160 ? Best regards, ronan.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?463F2E8A.5080204>