Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 15 Feb 2007 21:07:27 -0800
From:      Sam Leffler <sam@errno.com>
To:        Larry Martin <Larry@syatech.com>
Cc:        freebsd-current@freebsd.org
Subject:   Re: CFT: newath  hal
Message-ID:  <45D53C0F.6080405@errno.com>
In-Reply-To: <200702152251.l1FMp2L8008014@syatech.com>
References:  <200702152251.l1FMp2L8008014@syatech.com>

next in thread | previous in thread | raw e-mail | index | archive | help
Larry Martin wrote:
> I'm trying to work with 11g/5MHz channels and tried the new 0.9.30.7
> ath_hal, but found that channel 33 for example still resulted in a 20MHz
> wide channel as seen on a spectrum analyzer.  The 11a/5MHz PSB channels
> (82 for example) are 5MHz wide as expected.
> 
> I'm using a Wistron CM9 card (Atheros 5212?) and expected that I'd still
> see the 5MHz output, just still in the 2.4GHz band instead of 900MHz. 
> Is this correct?

No.  What you are doing is not supported.  There is only support for SR9
cards and for operating "5212 cards" in the public safety band.

>
> One additional note:  I'm transmitting packets via the BPF packet
> injection code, which works very well for my purposes.  I don't think
> this should affect the channel bandwidth.   I've tried specifying
> transmit data rates of both 1.5 and 6.0 Mb/s.  Interestingly, at 1.5
> Mb/s the receiver shows that the receive data rate is 1.5 Mb/s, but the
> actual throughput is ~3 Mb/s (which maybe sorta almost makes sense if
> it's still transmitting on a 20MHz channel?) I hope to capture the
> transmissions on a third radio with tcpdump to see what's really
> happening there.  Maybe that will provide additional insight into the 5
> vs 20MHz issue.
> 
> awn2# sysctl dev.ath.0.countrycode=843
> dev.ath.0.countrycode: 0 -> 843
> 
> awn2# ifconfig ath0 list chan
> Channel   3 : 907* Mhz 11g/5Mhz     Channel  23 : 917* Mhz 11g/5Mhz
> Channel   4 : 907* Mhz 11g/10Mhz    Channel  24 : 917* Mhz 11g/10Mhz
> Channel  13 : 912* Mhz 11g/5Mhz     Channel  26 : 917* Mhz 11g
> Channel  14 : 912* Mhz 11g/10Mhz    Channel  33 : 922* Mhz 11g/5Mhz
> Channel  16 : 912* Mhz 11g          Channel  34 : 922* Mhz 11g/10Mhz
> 
> awn2# sysctl hw.ath
> hw.ath.hal.version: 0.9.30.7
> hw.ath.hal.dma_brt: 2
> hw.ath.hal.sw_brt: 10
> hw.ath.hal.swba_backoff: 0
> hw.ath.dwell: 200
> hw.ath.calibrate: 30
> hw.ath.outdoor: 1
> hw.ath.xchanmode: 1
> hw.ath.countrycode: 0
> hw.ath.regdomain: 0
> hw.ath.rxbuf: 40
> hw.ath.txbuf: 100
> 
> _______________________________________________
> freebsd-current@freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
> 
> 




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?45D53C0F.6080405>