Date: Thu, 05 Aug 2004 21:29:52 -0400 From: "Michael Roberts" <tpen0010@hotmail.com> To: freebsd-hardware@freebsd.org Subject: RE: DLink DWL-G650 (h/w ver. B4) Message-ID: <BAY10-F55vqgStMVhEU000011cf@hotmail.com>
next in thread | raw e-mail | index | archive | help
Sorry, forgot to put the card in before running dmesg... the card adds the following lines to dmesg: ath0: <Atheros 5212> mem 0xf6010000-0xf601ffff irq 11 at device 0.0 on cardbus0 ath0: [GIANT-LOCKED] ath0: mac 5.9 phy 4.3 5ghz radio 4.6 ath0: Ethernet address: 00:0d:88:ac:83:77 ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps >From: "Michael Roberts" <tpen0010@hotmail.com> >To: freebsd-hardware@freebsd.org >Subject: RE: DLink DWL-G650 (h/w ver. B4) >Date: Thu, 05 Aug 2004 21:25:09 -0400 > >In case anyone cares, I'm going to reply to my own post, having found some >solution to the problem, but a few more problems. > >After a cvsup (august 3), rebuild of world, and kernel with the ath >drivers, the card does now work. When I plug it in, I don't get the same >errors as below, but instead the normal readout for a wireless card. I >guess there was something incompatible between my kernel rebuild and world? > I don't know... > >However, now another problem has cropped up. When I have the card in, if I >do ># ifconfig ath0 up >I get a kernel panic. I have to first do ># ifconfig bfe0 down >in order to bring ath0 up. Then, if I bring bfe0 back up again, I get a >kernel panic, regardless of whether the ath0 card is up or down, in the >slot or detached. > >The only thing I can think is that both are using irq 11 and device 0.0. I >would guess this is a conflict, no? I know it's not a problem for them to >use the same irq, but the same device number? I've seen posts which say >that acpi makes all of this ok.. but I don't know much about it. > >dmesg is below. Thanks for any help. > >Mike > >~# uname -a >FreeBSD trace.cable.rcn.com 5.2-CURRENT FreeBSD 5.2-CURRENT #4: Tue Aug 3 >22:00:38 EDT 2004 root@trace.cable.rcn.com:/usr/obj/usr/src/sys/PKERNEL > i386 > >dmesg: > >Copyright (c) 1992-2004 The FreeBSD Project. >Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. >FreeBSD 5.2-CURRENT #4: Tue Aug 3 22:00:38 EDT 2004 > root@trace.cable.rcn.com:/usr/obj/usr/src/sys/PKERNEL >WARNING: Kernel preemption is disabled, expect reduced performance. >Timecounter "i8254" frequency 1193182 Hz quality 0 >CPU: Intel(R) Pentium(R) M processor 2.00GHz (1993.54-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6 > >Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> >real memory = 536535040 (511 MB) >avail memory = 511078400 (487 MB) >npx0: [FAST] >npx0: <math processor> on motherboard >npx0: INT 16 interface >acpi0: <DELL CPi R > on motherboard >acpi0: [GIANT-LOCKED] >Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 >acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 >cpu0: <ACPI CPU (4 Cx states)> port 0x530-0x537 on acpi0 >acpi_tz0: <Thermal Zone> port 0x530-0x537 on acpi0 >acpi_acad0: <AC Adapter> on acpi0 >acpi_cmbat0: <Control Method Battery> on acpi0 >acpi_cmbat1: <Control Method Battery> on acpi0 >acpi_lid0: <Control Method Lid Switch> on acpi0 >acpi_button0: <Power Button> on acpi0 >acpi_button1: <Sleep Button> on acpi0 >pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 >pci0: <ACPI PCI bus> on pcib0 >agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xe7ffffff at device >0.0 on pci0 >pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 >pci1: <ACPI PCI bus> on pcib1 >nvidia0: <GeForce FX Go5200> mem >0xd0000000-0xdfffffff,0xfc000000-0xfcffffff irq 11 at device 0.0 on pci1 >nvidia0: [GIANT-LOCKED] >uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq >11 at device 29.0 on pci0 >uhci0: [GIANT-LOCKED] >usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 >usb0: USB revision 1.0 >uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub0: 2 ports with 2 removable, self powered >ums0: vendor 0x062a product 0x0000, rev 1.10/2.04, addr 2, iclass 3/1 >ums0: 5 buttons and Z dir. >uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq >11 at device 29.1 on pci0 >uhci1: [GIANT-LOCKED] >usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 >usb1: USB revision 1.0 >uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub1: 2 ports with 2 removable, self powered >uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq >11 at device 29.2 on pci0 >uhci2: [GIANT-LOCKED] >usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 >usb2: USB revision 1.0 >uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub2: 2 ports with 2 removable, self powered >pci0: <serial bus, USB> at device 29.7 (no driver attached) >pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 >pci2: <ACPI PCI bus> on pcib2 >bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xfaffe000-0xfaffffff irq 11 at >device 0.0 on pci2 >miibus0: <MII bus> on bfe0 >bmtphy0: <BCM4401 10/100baseTX PHY> on miibus0 >bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >bfe0: Ethernet address: 00:0f:1f:15:e6:b5 >bfe0: [GIANT-LOCKED] >cbb0: <TI4510 PCI-CardBus Bridge> at device 1.0 on pci2 >cardbus0: <CardBus bus> on cbb0 >pccard0: <16-bit PCCard bus> on cbb0 >fwohci0: <1394 Open Host Controller Interface> mem >0xfaff8000-0xfaffbfff,0xfaffd800-0xfaffdfff irq 11 at device 1.1 on pci2 >fwohci0: [GIANT-LOCKED] >fwohci0: OHCI version 1.10 (ROM=0) >fwohci0: No. of Isochronous channels is 4. >fwohci0: EUI64 32:4f:c0:00:34:ec:78:81 >fwohci0: Phy 1394a available S400, 2 ports. >fwohci0: Link S400, max_rec 2048 bytes. >firewire0: <IEEE1394(FireWire) bus> on fwohci0 >fwe0: <Ethernet over FireWire> on firewire0 >if_fwe0: Fake Ethernet address: 32:4f:c0:ec:78:81 >fwe0: Ethernet address: 32:4f:c0:ec:78:81 >sbp0: <SBP-2/SCSI over FireWire> on firewire0 >fwohci0: Initiate bus reset >fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode >firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) >firewire0: bus manager 0 (me) >pci2: <network> at device 3.0 (no driver attached) >isab0: <PCI-ISA bridge> at device 31.0 on pci0 >isa0: <ISA bus> on isab0 >atapci0: <Intel ICH4 UDMA100 controller> port >0xbfa0-0xbfaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 >ata0: at 0x1f0 irq 14 on atapci0 >ata1: at 0x170 irq 15 on atapci0 >pcm0: <Intel ICH4 (82801DB)> port 0xbc40-0xbc7f,0xb800-0xb8ff mem >0xf4fff400-0xf4fff4ff,0xf4fff800-0xf4fff9ff irq 11 at device 31.5 on pci0 >pcm0: [GIANT-LOCKED] >pcm0: <SigmaTel STAC9750/51 AC97 Codec> >pci0: <simple comms> at device 31.6 (no driver attached) >atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 >atkbd0: <AT Keyboard> irq 1 on atkbdc0 >kbd0 at atkbd0 >atkbd0: [GIANT-LOCKED] >psm0: <PS/2 Mouse> irq 12 on atkbdc0 >psm0: [GIANT-LOCKED] >psm0: model GlidePoint, device ID 0 >orm0: <ISA Option ROMs> at iomem 0xcf800-0xcffff,0xc0000-0xcf7ff on isa0 >pmtimer0 on isa0 >fdc0: ready for input in output >fdc0: cmd 3 failed at out byte 1 of 3 >ppc0: parallel port not found. >sc0: <System console> at flags 0x100 on isa0 >sc0: VGA <16 virtual consoles, flags=0x300> >sio0: configured irq 4 not in bitmap of probed irqs 0 >sio0: port may not be enabled >sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >sio0: type 8250 or not responding >sio1: configured irq 3 not in bitmap of probed irqs 0 >sio1: port may not be enabled >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >Timecounter "TSC" frequency 1993539572 Hz quality 800 >Timecounters tick every 10.000 msec >IPsec: Initialized Security Association Processing. >acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% >cpu0: Performance states changed >ad0: 57231MB <TOSHIBA MK6021GAS> [116280/16/63] at ata0-master UDMA100 >ATAPI_RESET time = 10us >acd0: CDRW <_NEC DVD+RW ND-6100A> at ata1-master UDMA33 >cd0 at ata1 bus 0 target 0 lun 0 >cd0: <_NEC DVD+RW ND-6100A 104D> Removable CD-ROM SCSI-0 device >cd0: 33.000MB/s transfers >cd0: Attempt to query device size failed: NOT READY, Medium not present >Mounting root from ufs:/dev/ad0s4a > _________________________________________________________________ Express yourself instantly with MSN Messenger! Download today - it's FREE! http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BAY10-F55vqgStMVhEU000011cf>