Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 15 Apr 2014 19:37:22 +1000
From:      Da Rock <freebsd-questions@herveybayaustralia.com.au>
To:        Adrian Chadd <adrian@freebsd.org>
Cc:        FreeBSD Questions <freebsd-questions@freebsd.org>
Subject:   Re: FBSD10 Atheros wifi not working
Message-ID:  <534CFDD2.4070301@herveybayaustralia.com.au>
In-Reply-To: <CAJ-Vmomb2d7jdPRmruaYK1LJ6gZ62_=4N3Ko9Z2eANLJ02c6Rw@mail.gmail.com>
References:  <534B32FA.30500@herveybayaustralia.com.au> <CAJ-Vmok9Y2Dkgh=x2kP8su7LjrVo==ijSJ5GYrc=wzZv0uwNgQ@mail.gmail.com> <534BC380.90608@herveybayaustralia.com.au> <CAJ-Vmomb2d7jdPRmruaYK1LJ6gZ62_=4N3Ko9Z2eANLJ02c6Rw@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On 04/15/14 12:16, Adrian Chadd wrote:
> Wait, you don't have this problem on the install image when running from USB?
No, I don't believe so. It was a quick install, but it was capable of 
scanning for AP's and obtaining an IP. Can't do either now with the 
installed system.

I suppose that's the weird part... been trying to figure out the diff 
ever since.
>
>
> -a
>
>
> On 14 April 2014 04:16, Da Rock
> <freebsd-questions@herveybayaustralia.com.au> wrote:
>> Finally got the email client working again on the walking dead system :)
>>
>> On 04/14/14 13:57, Adrian Chadd wrote:
>>> Hi!
>> I was hoping you were tuned in. If you can get this thing sorted again I'll
>> owe you one!
>>
>>> You never said exactly what hardware it is Can you include a dmesg of
>>> the relevant bits during boot?
>> Sorry, that was a bit remiss wasn't it? I had the info to put in too... its
>> the AR9285 atheros chipset.
>>
>> dmesg is a bit harder being on a different system. I'll try and get the info
>> in order though, at the time I was reading off the scrolling output from
>> vt1. The error(s) are repetitive though, so I'll just offer one cycle. It
>> doesn't seem to necessarily follow any real order though, from my
>> observation.
>>
>> ath0: ath_reset_grablock: didn't finish after 10 iterations
>> ath0: ath_reset_grablock: warning, recursive reset path!
>> ath0: ath_reset: concurrent reset! danger!
>> ath0: ath_reset: unable to reset hardware; hal status 14
>> ath0: ath_chanset: unable to reset channel <channel>, hal status 14
>> ...
>> ath0: ath_reset: unable to reset hardware; hal status 14
>>
>>> Anything like the above kinda indicates there's some bigger issue going
>>> on.
>> I can't imagine its a hardware issue as it seems to work with other systems
>> (like the install memdisk). I thought with the hal debug sysctl being
>> available it would offer more info, but it seems it may not even be in the
>> kernel although there is a sysctl. I tried compiling a new kernel with the
>> debug options, but the backup battery is not working properly so it depends
>> on ntpd to set the correct time, and the make requires the correct time set;
>> so I'll have to address that before I can continue that course.
>>
>> Argh! The joys of Murphy and his damned laws!
>>
>>>
>>> -a
>>>
>>>
>>>
>>> On 13 April 2014 17:59, Da Rock
>>> <freebsd-questions@herveybayaustralia.com.au> wrote:
>>>> The subject line may not be very descriptive, but I'm not sure exactly
>>>> where
>>>> to point as to the problem. All other similar issues are a few years old
>>>> now, and on 8,9, some 7's.
>>>>
>>>> Long story short I'm just installing 10 (finally) on my laptop, and I
>>>> need
>>>> to get it back up and running asap as I am swamped in work. I didn't
>>>> think
>>>> it would be an issue as 9 had a decent working ath driver and I thought
>>>> it
>>>> could only get better. I'm now emailing using yet another system with the
>>>> same device on 9, but a dying hdd which obviously also needs a reinstall
>>>> on
>>>> new hdd. Wired is no good as we aren't equipped.
>>>>
>>>> So in bsdinstall, all works well and it sets up wifi easily. Reboot into
>>>> the
>>>> new system an it has a coronary with messages from ath_reset_grablock,
>>>> ath_reset, ath_raw_xmit, ath_chan_set, ath_legacy_rx_tasklet:
>>>>
>>>> ath_reset: concurrent reset! danger!
>>>>
>>>> ath_reset_grablock: didn't finish after 10 iterations
>>>> ath_reset_grablock: warning, recursive reset path!
>>>>
>>>> ath_chan_set: concurrent reset! danger!
>>>>
>>>> ath_raw_xmit: sc_inreset_cnt > 0; bailing
>>>>
>>>> ath_legacy_rx_tasklet: sc_inreset_cnt > 0; bailing
>>>>
>>>> Scanning doesn't work; ath0 says it is associated, but wlan0 says no
>>>> channel.
>>>>
>>>> I've set dev.ath.0.hal.debug=1, but there is no ath.0.debug either under
>>>> dev
>>>> or hw. I tried compiling the tools but it failed for lack of gcc.
>>>>
>>>> TIA guys, but I am really under the pump here as I thought this would be
>>>> a
>>>> quick up and go now with the pkgng system as well in play. Now I'm up the
>>>> proverbial creek without a paddle.
>>>>
>>>> Cheers
>>>> _______________________________________________
>>>> freebsd-questions@freebsd.org mailing list
>>>> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>>>> To unsubscribe, send any mail to
>>>> "freebsd-questions-unsubscribe@freebsd.org"
>>> _______________________________________________
>>> freebsd-questions@freebsd.org mailing list
>>> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>>> To unsubscribe, send any mail to
>>> "freebsd-questions-unsubscribe@freebsd.org"
>>
>> _______________________________________________
>> freebsd-questions@freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
>> To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org"




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?534CFDD2.4070301>