Date: Tue, 26 Oct 1999 20:57:26 +1000 From: Peter Jeremy <jeremyp@gsmx07.alcatel.com.au> To: freebsd-alpha@FreeBSD.org Subject: Multia booting woes Message-ID: <99Oct26.205237est.40358@border.alcanet.com.au>
next in thread | raw e-mail | index | archive | help
I thought this was all going to be easy when I decided to buy
a Multia...
Latest try: I've dd'd releases/3.2-RELEASE/floppies/boot.flp from
3.2-RELEASE CD-ROM 2 onto a SCSI disk, stuck the disk into the Multia
and it still dies (log below). I presume the `Unit Attention'
messages are being triggered by SCSI bus resets during the boot,
rather than a disk problem.
Any suggestions?
(`%' in the following refers to the twirling bar).
Testing Memory from 8 to 64 meg...
Executing power-up script...
Testing TGA
version BL5 V3.8-3 Aug 10 1995 03:22:55
dka0.0.0.6.0 DKA0 SEAGATE ST32151N 9470
ewa0.0.0.8.0 EWA0 08-00-2B-E4-41-77
pka0.7.0.6.0 PKA0 SCSI Bus ID 7
64 Meg of system memory
CPU speed is 166 MHZ
Cache size is 256 Kbytes
*** keyboard not plugged in...
Keyboard error; using serial port terminal
Switching network ewa0.0.0.8.0 from AUI to Thin Wire...
Switching network ewa0.0.0.8.0 from Thin Wire to Twisted Pair...
>>>boot dka0
(boot dka0.0.0.6.0 -flags 0)
*** Soft Error - Error #27 - SCSI:
sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0
Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019
boot 00000089 0 0 0 1 19:45:39
*** End of Error ***
block 0 of dka0.0.0.6.0 is a valid boot block
reading 14 blocks from dka0.0.0.6.0
bootstrap code read in
base = 166000, image_start = 0, image_bytes = 1c00
initializing HWRPB at 2000
initializing page table at 158000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
*** Soft Error - Error #27 - SCSI:
sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0
Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019
boot 00000089 0 0 0 2 19:45:41
*** End of Error ***
%Console: SRM firmware console
VMS PAL rev: 0x1000000010530
OSF PAL rev: 0x1000000020123
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision
(jkh@beast.cdrom.com, Sun May 16 17:48:25 GMT 1999)
Memory: 65536 k
*** Soft Error - Error #27 - SCSI:
sense key = 'Unit Attention' (29|02) from dka0.0.0.6.0
Diagnostic Name ID Device Pass Test Hard/Soft 26-OCT-2019
boot 00000089 0 0 0 3 19:45:44
*** End of Error ***
%> load /kernel
%inflate: (null)
panic: free: guard1 fail @ 0x200094a0
halted CPU 0
halt code = 5
HALT instruction executed
PC = 2001f3b8
access violation fault
PCB = 03F542C0 (entry)
PC = 0004FED0
VA = 00000028
exception context saved starting at 03F562C0
GPRs:
0: 00000000 00000000 16: 00000000 00000000
1: 00000000 000BFFFF 17: 00000000 000E1518
2: 00000000 0010B610 18: 00000000 000464D4
3: 00000000 00038B20 19: 00000000 00109390
4: 00000000 00000000 20: 00000000 00038320
5: 00000000 00038B20 21: 00000000 00110CA0
6: 00000000 00000000 22: 00000000 00142B90
7: 00000000 00000000 23: 00000000 00000000
8: 00000000 00000000 24: 00000000 00000000
9: 00000000 00000000 25: 00000000 00000002
10: 00000000 00000000 26: 00000000 0004FEB0
11: 00000000 00000000 27: 00000000 00114228
12: 00000000 00000000 28: 00000000 00016050
13: 00000000 00000000 29: 00000000 03F56428
14: 00000000 00000000 30: 00000000 03F56428
15: 00000000 00000000
dump of active call frames:
PC = 0004FED0
PD = 0010B610 (decc$fclose)
FP = 03F56428
SP = 03F56428
R2 R3 R4 R29 saved starting at 03F56430
R2 = 00111A30
R3 = 03F542C0
R4 = 03F54398
R29 = 03F56458
PC = 0006A83C
PD = 00111A30 (krn$_process)
FP = 03F56458
SP = 03F56458
R2 R3 R4 R5 R29 saved starting at 03F56460
R2 = 00000000
R3 = 00000000
R4 = 00000000
R5 = 00000000
R29 = 00000000
Brk 0 at 0012FF08
0012FF08! BPT
--
Peter Jeremy (VK2PJ) peter.jeremy@alcatel.com.au
Alcatel Australia Limited
41 Mandible St Phone: +61 2 9690 5019
ALEXANDRIA NSW 2015 Fax: +61 2 9690 5982
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?99Oct26.205237est.40358>