Date: Mon, 18 Jun 2001 21:20:39 -0700 (PDT) From: Brad McNeney <mcneney@cs.sfu.ca> To: Joe Clarke <marcus@marcuscom.com> Cc: questions@FreeBSD.ORG Subject: Re: trouble exporting fs Message-ID: <Pine.OSF.4.21.0106182119250.10444-100000@smahlt.math.sfu.ca> In-Reply-To: <20010619001213.G14681-100000@shumai.marcuscom.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Yes, /home is a mounted partition: cr269907-a% df Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/ad0s1a 49583 38838 6779 85% / /dev/ad0s1g 7496178 12110 6884374 0% /home /dev/ad0s1f 5954477 2233286 3244833 41% /usr /dev/ad0s1e 19815 16767 1463 92% /var procfs 4 4 0 100% /proc On Tue, 19 Jun 2001, Joe Clarke wrote: > Is /home a mounted partition? You should specify mounted partitions only > in /etc/exports. If your client needs to mount subdirectories on the > partition, consider the following: > > /usr /usr/home 192.168.100.200 > > Then, the client can mount /usr/home on /home. > > Joe Clarke > > On Mon, 18 Jun 2001, Brad McNeney wrote: > > > > > I'm having trouble exporting a filesystem on from a machine > > running FreeBSD 4.3-STABLE to a Linux machine (RedHat 6.2). > > The FreeBSD computer has 2 NICs. The external is connected to a > > cable modem and the internal to a hub on a LAN with network addresses > > 192.168.100.xxx. The computer I want to export to has IP 192.168.100.200 > > > > The relevant part of dmesg (full output clipped below) reads: > > Starting final network daemons: > > mountd > > Jun 18 20:51:36 cr269907-a mountd[165]: can't export /home > > Jun 18 20:51:36 cr269907-a mountd[165]: bad exports list line /home > > 192.168.100.200 > > > > My /etc/exports file has just the one line: > > > > /home 192.168.100.200 > > > > > > Output from netstat -rn: > > > > Routing tables > > > > Internet: > > Destination Gateway Flags Netif Expire > > default 24.113.160.1 UGSc dc0 > > 24.113.160/22 link#1 UC dc0 => > > 127.0.0.1 127.0.0.1 UH lo0 > > 192.168.100 link#2 UC ed0 => > > > > Internet6: > > Destination Gateway Flags Netif Expire > > ::1 ::1 UH lo0 > > fe80::%dc0/64 link#1 UC dc0 > > fe80::%ed0/64 link#2 UC ed0 > > fESG::%lo0/64 fe80::1%lo0 Uc lo0 > > ff01::/32 ::1 U lo0 > > ff02::%dc0/32 link#1 UC dc0 > > ff02::%ed0/32 link#2 UC ed0 > > ff02::%lo0/32 fe80::1%lo0 UC lo0 > > > > > > Any ideas on what I'm doing wrong? > > > > Brad > > > > ----------------------------------------------------------------------- > > Full output from dmesg: > > > > Copyright (c) 1992-2001 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights reserved. > > FreeBSD 4.3-STABLE #0: Sun Jun 17 17:04:22 PDT 2001 > > root@cr269907-a.poco1.bc.wave.home.com:/usr/obj/usr/src/sys/MYKERNEL > > Timecounter "i8254" frequency 1193182 Hz > > CPU: Pentium III/Pentium III Xeon/Celeron (1004.52-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0x686 Stepping = 6 > > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > > real memory = 536854528 (524272K bytes) > > config> di pcic0 > > config> di sn0 > > config> di lnc0 > > config> di ie0 > > config> di fe0 > > config> di ed0 > > config> di cs0 > > config> en pcic1 > > config> po pcic1 0x3e2 > > config> ir pcic1 11 > > config> iom pcic1 0xd4000 > > config> f pcic1 0 > > config> q > > avail memory = 518311936 (506164K bytes) > > Preloaded elf kernel "kernel" at 0xc0459000. > > Preloaded userconfig_script "/boot/kernel.conf" at 0xc045909c. > > Preloaded elf module "splash_bmp.ko" at 0xc04590ec. > > Pentium Pro MTRR support enabled > > md0: Malloc disk > > module_register_init: MOD_LOAD (splash_bmp, c0454798, 0) error 2 > > npx0: <math processor> on motherboard > > npx0: INT 16 interface > > pcib0: <Host to PCI bridge> on motherboard > > pci0: <PCI bus> on pcib0 > > pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0 > > pci1: <PCI bus> on pcib2 > > pci1: <NVidia Riva Ultra Vanta TNT2 graphics accelerator> at 0.0 irq 9 > > isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0 > > isa0: <ISA bus> on isab0 > > atapci0: <VIA 82C686 ATA66 controller> port 0xd800-0xd80f at device 4.1 on pci0 > > ata0: at 0x1f0 irq 14 on atapci0 > > ata1: at 0x170 irq 15 on atapci0 > > uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 10 at device 4.2 on pci0 > > usb0: <VIA 83C572 USB controller> on uhci0 > > usb0: USB revision 1.0 > > uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub0: 2 ports with 2 removable, self powered > > uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 10 at device 4.3 on pci0 > > usb1: <VIA 83C572 USB controller> on uhci1 > > usb1: USB revision 1.0 > > uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub1: 2 ports with 2 removable, self powered > > dc0: <Macronix 98715/98715A 10/100BaseTX> port 0xb800-0xb8ff mem 0xf7800000-0xf78000ff irq 5 at device 9.0 on pci0 > > dc0: Ethernet address: 00:80:c6:f9:c3:83 > > miibus0: <MII bus> on dc0 > > dcphy0: <Intel 21143 NWAY media interface> on miibus0 > > dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xb400-0xb41f irq 11 at device 11.0 on pci0 > > ed0: address 00:60:67:3b:de:ef, type NE2000 (16 bit) > > pcib1: <Host to PCI bridge> on motherboard > > pci2: <PCI bus> on pcib1 > > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > > fdc0: FIFO enabled, 8 bytes threshold > > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > > kbd0 at atkbd0 > > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > > psm0: model 4D Mouse, device ID 6 > > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > > sc0: <System console> at flags 0x100 on isa0 > > sc0: VGA <16 virtual consoles, flags=0x300> > > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > > sio0: type 16550A > > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > > sio1: type 16550A > > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > > ppc0: FIFO with 16/16/8 bytes threshold > > ppbus0: IEEE1284 device found /NIBBLE/PS2/ECP > > Probing for PnP devices on ppbus0: > > ppbus0: <Lexmark International Lexmark Optra E310> PRINTER PCL 6 Emulation, PostScript Level 2 Emulation, NPAP, PJL > > plip0: <PLIP network interface> on ppbus0 > > lpt0: <Printer> on ppbus0 > > lpt0: Interrupt-driven port > > ppi0: <Parallel I/O> on ppbus0 > > ad0: 14655MB <Maxtor 91536U3> [29777/16/63] at ata0-master UDMA66 > > acd0: CDROM <ASUS CD-S500/A> at ata1-slave using PIO4 > > Mounting root from ufs:/dev/ad0s1a > > swapon: adding /dev/ad0s1b as swap device > > Automatic boot in progress... > > /dev/ad0s1a: > > FILESYSTEM CLEAN; SKIPPING CHECKS > > /dev/ad0s1a: > > clean, 10754 free > > (346 frags, 1301 blocks, 0.7% fragmentation) > > /dev/ad0s1g: > > FILESYSTEM CLEAN; SKIPPING CHECKS > > /dev/ad0s1g: > > clean, 7484077 free > > (581 frags, 935437 blocks, 0.0% fragmentation) > > /dev/ad0s1f: > > FILESYSTEM CLEAN; SKIPPING CHECKS > > /dev/ad0s1f: > > clean, 3721191 free > > (51167 frags, 458753 blocks, 0.9% fragmentation) > > /dev/ad0s1e: > > FILESYSTEM CLEAN; SKIPPING CHECKS > > /dev/ad0s1e: > > clean, 3037 free > > (61 frags, 372 blocks, 0.3% fragmentation) > > Doing initial network setup: > > hostname > > . > > dc0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > > inet 24.113.163.96 netmask 0xfffffc00 broadcast 24.113.163.255 > > inet6 fe80::280:c6ff:fef9:c383%dc0 prefixlen 64 tentative scopeid 0x1 > > ether 00:80:c6:f9:c3:83 > > media: autoselect (none) status: active > > supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP 100baseTX <hw-loopback> none > > ed0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > > inet 192.168.100.100 netmask 0xffffff00 broadcast 192.168.100.255 > > inet6 fe80::260:67ff:fe3b:deef%ed0 prefixlen 64 tentative scopeid 0x2 > > ether 00:60:67:3b:de:ef > > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 > > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x9 > > inet6 ::1 prefixlen 128 > > inet 127.0.0.1 netmask 0xff000000 > > add net default: gateway 24.113.160.1 > > Additional routing options: > > TCP keepalive=YES > > . > > Routing daemons: > > . > > Additional daemons: > > syslogd > > . > > Doing additional network setup: > > portmap > > . > > Starting final network daemons: > > mountd > > Jun 18 20:51:36 cr269907-a mountd[165]: can't export /home > > Jun 18 20:51:36 cr269907-a mountd[165]: bad exports list line /home 192.168.100.200 > > nfsd > > rpc.statd > > . > > ELF ldconfig path: /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib > > a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout > > Starting standard daemons: > > inetd > > cron > > sendmail > > . > > Jun 18 20:51:37 cr269907-a sendmail[197]: f5J30aE44624: SYSERR(root): Cannot open hash database /etc/mail/aliases.db: Inappropriate file type or format > > Initial rc.i386 initialization: > > . > > Configuring syscons: > > blank_time > > screensaver > > moused > > . > > Additional ABI support: > > linux > > . > > Local package initialization: > > apache > > mysql > > . > > Additional TCP options: > > . > > > > Mon Jun 18 20:51:43 PDT 2001 > > kill: > > 45246 > > : > > No such process > > Jun 18 20:52:10 cr269907-a login: ROOT LOGIN (root) ON ttyv0 > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.OSF.4.21.0106182119250.10444-100000>