Date: Fri, 22 Nov 2002 08:33:18 +0100 (CET) From: Josef Jursa <jjursa@ibp.cz> To: freebsd-bugs@FreeBSD.org Subject: AIC 7902 on Super Micro P4DP8 G2 Message-ID: <Pine.BSI.4.05L.10211220822120.2225-100000@zoncna.ibp.cz>
next in thread | raw e-mail | index | archive | help
Hello,
I have problems with the Adaptec AIC 7902 integrated on Super Micro P4DP8
G2 manboard in FReeFSD 4.7. (Hardware is O.K. - it is running under RedHat
7.3.) There is ahd compiled into the kernel, but it is not running. I am
adding the dmesg.
I would appreciate very much if somebody could help me. Replay to
jjursa@ibp.cz please.
Best regards,
Josef Jursa
P.S.
All PCI slots are free.
dmesg:
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE-p2 #0: Mon Nov 18 16:29:42 CET 2002
root@orel.ibp.cz:/usr/src/sys/compile/IVO
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium 4 (2399.74-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory = 536346624 (523776K bytes)
avail memory = 513404928 (501372K bytes)
Preloaded elf kernel "kernel" at 0xc0820000.
Preloaded mfs_root "/mfsroot" at 0xc082009c.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03e6e0c
md1: Malloc disk
Using $PIR table, 29 entries at 0xc00fddf0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on
pci1
pci2: <PCI bus> on pcib2
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on
pci1
pci3: <PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.14> port
0x3000-0x303f mem 0xfc200000-0xfc21ffff irq 11 at device 2.0 on pci3
em0: Speed:100 Mbps Duplex:Full
em1: <Intel(R) PRO/1000 Network Connection, Version - 1.3.14> port
0x3040-0x307f mem 0xfc220000-0xfc23ffff irq 11 at device 2.1 on pci3
em1: Speed:N/A Duplex:N/A
pcib4: <PCI to PCI bridge (vendor=8086 device=2545)> at device 3.0 on pci0
pci4: <PCI bus> on pcib4
pci4: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib5: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on
pci4
pci5: <PCI bus> on pcib5
pci4: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib6: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on
pci4
pci6: <PCI bus> on pcib6
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x2000-0x201f
irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
.
.
.
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
module_register: module pci/mlx already exists!
linker_file_sysinit "mlx.ko" failed to register! 17
module_register: module pci/amr already exists!
linker_file_sysinit "amr.ko" failed to register! 17
module_register: module pci/twe already exists!
linker_file_sysinit "twe.ko" failed to register! 17
module_register: module pci/mly already exists!
linker_file_sysinit "mly.ko" failed to register! 17
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset! Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-bugs" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSI.4.05L.10211220822120.2225-100000>