Date: Mon, 13 May 2002 01:04:44 +0900 From: Norikatsu Shigemura <nork@FreeBSD.org> To: freebsd-stable@FreeBSD.org Cc: lambert@lambertfam.org, ytsuji@mn.waseda.ac.jp Subject: Re: fasttrak100 Message-ID: <200205121604.g4CG4jJq028117@nd250009.gab.xdsl.ne.jp> In-Reply-To: <20020512033329.GB35818@laptop.lambertfam.org> References: <Pine.GSO.4.10.10205100811090.22466-100000@pcnet1.pcnet.com> <200205110002.JAA16267@wise13.mn.waseda.ac.jp> <20020512033329.GB35818@laptop.lambertfam.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Dear.
Sorry, It may be that my case isn't related to this.
On Sat, 11 May 2002 23:33:29 -0400
"Scott Lambert" <lambert@lambertfam.org> wrote:
> I am using a Promise FastTrak TX4 ATA100 in my personal web server.
I am using like this(on board RAID chipset), too. According to
machine's documents, it use Promise PDC20265, and boot message
is following this line(necessary).
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
atapci1: <Promise ATA100 controller> port 0xcc00-0xcc3f,0xd000-0xd003,0xd400-0xd407,0xd800-0xd803,0xdc00-0xdc07 mem 0xdffe0000-0xdfffffff irq 10 at device 16.0 on pci0
ata2: at 0xdc00 on atapci1
ata3: at 0xd400 on atapci1
ar0: 76319MB <ATA RAID1 array> [9729/255/63] status: READY subdisks:
0 READY ad0: 76319MB <ST380021A> [155061/16/63] at ata2-master UDMA100
1 READY ad1: 76319MB <ST380021A> [155061/16/63] at ata3-master UDMA100
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
> It is setup to mirror two drives. You should see an ar0 device in
> addition to the usual ad0 and ad1 devices. Do you get the ar0 device?
> If so use it rather than the ad devices.
My machine was installed 4.5-RELEASE with RAID1(of course
good works) by CD-ROM, and updated 4.6-PRERELEASE by CVSup.
And I do make world && make kernel. But cannot boot(;_;).
> I think you should have it. I installed from the FreeBSD 4.5 CD and
> everything was detected and worked. I have since upgraded to -STABLE.
> The machine seems quite happy.
> I think it should just work for you. You may just be overlooking the
> ar0 device.
Reason for not boot, Because of new kernel couldn't find root
filesystem.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Mounting root from ufs:/dev/ar0s1a
ad0: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices ..
ad0: removed from configuration
ar0: WARNING - mirror lost
ad0: deleted from ar0 disk0
done
ad1: WRITE command timeout tag=0 serv=0 - resetting
ata3: resetting devices ..
ad1: removed from configuration
ar0: ERROR - array broken
ad1: deleted from ar0 disk1
ar0: ERROR - array broken
done
ar0: reading primary partition table: error reading fsbn 0
Root mount failed: 5
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot>
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
This following lines is FULL BOOT MESSAGE.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-PRERELEASE #0: Tue May 7 17:17:12 JST 2002
nork@XXXX.XXXXX.XX.XX:/usr/obj/usr/src/sys/XXXXXX
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (996.55-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 536805376 (524224K bytes)
avail memory = 518975488 (506812K bytes)
Preloaded elf kernel "kernel" at 0xc0350000.
VESA: v2.0, 8128k memory, flags:0x0, mode table:0xc02f1382 (1000022)
VESA: ATI MACH64
Pentium Pro MTRR support enabled
Using $PIR table, 10 entries at 0xc00f7700
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GM graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <VIA 83C572 USB controller> at 7.2 irq 12
pci0: <VIA 83C572 USB controller> at 7.3 irq 12
pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xc400-0xc43f mem 0xdfc00000-0xdfcfffff,0xdffbe000-0xdffbefff irq 9 at device 14.0 on pci0
fxp0: Ethernet address 00:20:ed:21:c5:ea
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xc800-0xc83f mem 0xdfe00000-0xdfefffff,0xdffbf000-0xdffbffff irq 12 at device 15.0 on pci0
fxp1: Ethernet address 00:20:ed:21:c5:eb
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
atapci1: <Promise ATA100 controller> port 0xcc00-0xcc3f,0xd000-0xd003,0xd400-0xd407,0xd800-0xd803,0xdc00-0xdc07 mem 0xdffe0000-0xdfffffff irq 10 at device 16.0 on pci0
ata2: at 0xdc00 on atapci1
ata3: at 0xd400 on atapci1
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
DUMMYNET initialized (011031)
IP packet filtering initialized, divert enabled, rule-based forwarding disabled, default to accept, unlimited logging
ar0: 76319MB <ATA RAID1 array> [9729/255/63] status: READY subdisks:
0 READY ad0: 76319MB <ST380021A> [155061/16/63] at ata2-master UDMA100
1 READY ad1: 76319MB <ST380021A> [155061/16/63] at ata3-master UDMA100
acd0: CDROM <SR243T> at ata1-master PIO4
Mounting root from ufs:/dev/ar0s1a
ad0: READ command timeout tag=0 serv=0 - resetting
ata2: resetting devices ..
ad0: removed from configuration
ar0: WARNING - mirror lost
ad0: deleted from ar0 disk0
done
ad1: WRITE command timeout tag=0 serv=0 - resetting
ata3: resetting devices ..
ad1: removed from configuration
ar0: ERROR - array broken
ad1: deleted from ar0 disk1
ar0: ERROR - array broken
done
ar0: reading primary partition table: error reading fsbn 0
Root mount failed: 5
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:/dev/da0s1a
? List valid disk boot devices
<empty line> Abort manual input
mountroot>
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200205121604.g4CG4jJq028117>