Date: Thu, 16 Nov 2000 00:05:47 -0800 From: Kent Stewart <kstewart@urx.com> To: Mark Sturge <techie-guy@home.com> Cc: freebsd-stable@FreeBSD.ORG Subject: Re: failed 'make buildworld' Message-ID: <3A13955B.98562EE8@urx.com> References: <3A138950.4E70B9E2@home.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Mark Sturge wrote: > > Hi all. > > I'm fairly new to FreeBSD and this is the first post I've felt necessary > > to make because I'm stumped on this one. > > I've cvsup'd my src and run 'make buildworld', but it has failed 3 times > > in a row. I've yet to have a problem with 'make buildworld' until now. > Here is the problem I'm having about 1.5 hrs into the process: I think you will need to turn off UDMA until you finish the upgrade to 4-stable. Most of the messages seem to have disappeared with the new drivers but getting to that point may be painful. You could also have a bad "ad1: 16500MB <FUJITSU MPD3173AT>" and it won't help. Kent > > ad1: WRITE command timeout - resetting > ata0: resetting devices .. ata0-slave: no status, rescheduling device > done. > ad1: HARD WRITE ERROR blk# 20566623 status=0f error=0f > ad1: soft error ECC corrected. > > ... blah blah blah and it continues with similar error messages. > > Eventually my box comes to a halt and I actually have to power down > without shutting down the system correctly. HDD problem? Looks to me > that it might be, but I'm not sure. 'make buildworld' has run > flawlessly in the past up to this point. > > Any advice would be appreciated... > > Mark > techie-guy@home.com > -- > > FreeBSD cr109568-a.lndn1.on.wave.home.com 4.1.1-RELEASE FreeBSD > 4.1.1-RELEASE #0: Tue Sep 26 00:46:59 GMT 2000 > jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC i386 > > Copyright (c) 1992-2000 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights > reserved. > FreeBSD 4.1.1-RELEASE #0: Tue Sep 26 00:46:59 GMT 2000 > jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium/P55C (233.86-MHz 586-class CPU) > Origin = "GenuineIntel" Id = 0x543 Stepping = 3 > Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX> > real memory = 67108864 (65536K bytes) > config> di psm0 > config> di sn0 > config> di lnc0 > config> di le0 > config> di ie0 > config> di fe0 > config> di ed0 > config> di cs0 > config> di bt0 > config> di aic0 > config> di aha0 > config> di adv0 > config> q > avail memory = 61214720 (59780K bytes) > Preloaded elf kernel "kernel" at 0xc0416000. > Preloaded userconfig_script "/boot/kernel.conf" at 0xc041609c. > Intel Pentium detected, installing workaround for F00F bug > md0: Malloc disk > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <Host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > isab0: <Intel 82371AB PCI to ISA bridge> at device 1.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 1.1 > > on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x6000-0x601f at > device 1.2 on pci0 > uhci0: Invalid irq 255 > uhci0: Please switch on USB support and switch PNP-OS to 'No' in BIOS > device_probe_and_attach: uhci0 attach returned 6 > chip1: <Intel 82371AB Power management controller> port 0x5c00-0x5c0f at > > device 1.3 on pci0 > pci0: <ATI Mach64-GU graphics accelerator> at 9.0 > pci0: <3Dfx Voodoo 2 graphics accelerator> at 10.0 > de0: <Digital 21041 Ethernet> port 0x6800-0x687f mem > 0xe2001000-0xe200107f irq 11 at device 11.0 on pci0 > de0: SMC 21041 [10Mb/s] pass 2.1 > de0: address 00:e0:29:1e:44:8e > isa0: too many dependant configs (8) > isa0: unexpected small tag 14 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on > isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/16 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > de0: enabling 10baseT port > ad0: 19546MB <FUJITSU MPF3204AT> [39714/16/63] at ata0-master using > UDMA33 > ad1: 16500MB <FUJITSU MPD3173AT> [33525/16/63] at ata0-slave using > UDMA33 > acd0: CDROM <MATSHITA CR-593> at ata1-master using PIO4 > Mounting root from ufs:/dev/ad1s1a > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-stable" in the body of the message -- Kent Stewart Richland, WA mailto:kbstew99@hotmail.com http://kstewart.urx.com/kstewart/index.html FreeBSD News http://daily.daemonnews.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3A13955B.98562EE8>