Date: Sun, 10 Dec 2000 08:37:18 +0800 From: "James Lim" <jameslpin@pacific.net.sg> To: "jfait" <jfait@voodoo.synux.de>, <questions@FreeBSD.ORG> Subject: Re: lpt0/ppbus0 Message-ID: <003c01c06241$60c9ad40$fa5e78cb@gchang> References: <Pine.BSF.3.96.1001210023328.2721A-100000@voodoo.synux.de>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi there, May i know wat brand of printer are you using? Did u enable lpd on ur rc.conf? You can try to follow one of the great printer tutorial on the following url: http://www.freebsddiary.org/apsfilter.html James Lim Technical Support Executive Pacific Internet Limited 89 Science Park Drive #02-05/06 The Rutherford Singapore 118261 Finger evilfry@sg.freebsd.org for PGP key. ----- Original Message ----- From: "jfait" <jfait@voodoo.synux.de> To: <questions@FreeBSD.ORG> Sent: Sunday, December 10, 2000 9:42 AM Subject: lpt0/ppbus0 > Help! > My printer does not work with FreeBSd, although it works fine with linux- > the hardware is all the same so I guess its my fault...your help is highly > welcome, please reply to jgfa@gmx.de > ___________________________________________ > FreeBSD 3.4-RELEASE #0: Mon Dec 20 06:54:39 GMT 1999 > jkh@time.cdrom.com:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: AMD-K6(tm) 3D processor (451.03-MHz 586-class CPU) > Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 > Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> > AMD Features=0x80000800<SYSCALL,3DNow!> > real memory = 67108864 (65536K bytes) > avail memory = 61747200 (60300K bytes) > Preloaded elf kernel "kernel" at 0xc035c000. > Probing for devices on PCI bus 0: > chip0: <VIA 82C598MVP (Apollo MVP3) host bridge> rev 0x04 on pci0.0.0 > chip1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI bridge> rev 0x00 on pci0.1.0 > chip2: <VIA 82C586 PCI-ISA bridge> rev 0x47 on pci0.7.0 > ide_pci0: <VIA 82C586x (Apollo) Bus-master IDE controller> rev 0x06 on > pci0.7.1 > chip3: <VIA 82C586B ACPI interface> rev 0x10 on pci0.7.3 > vga0: <S3 Trio graphics accelerator> rev 0x54 int a irq 10 on pci0.8.0 > Probing for devices on PCI bus 1: > Probing for PnP devices: > Probing for devices on the ISA bus: > Probing for PnP devices on ppbus0: > ppbus0: <Canon BJC-2000/1.01> PRINTER BJL,BJRaster,BSCC,TXT01 > lpt0: <generic printer> on ppbus 0 > lpt0: Interrupt-driven port > ppi0: <generic parallel i/o> on ppbus 0 > plip0: <PLIP network interface> on ppbus 0 > > voodoo# lpc status all > lp: > queuing is enabled > printing is enabled > 1 entry in spool area > printer idle > raw: > queuing is enabled > printing is enabled > no entries in spool area > printer idle > ______________________________ > ok, the printer did not print anything... > so I try again: > lptest 20 5 |lpr > voodoo# lpc status all > lp: > queuing is enabled > printing is enabled > 2 entries in spool area > lp is ready and printing > raw: > queuing is enabled > printing is enabled > no entries in spool area > printer idle > ______________________any idea ? > note : I am pretty familiar with AIX, HP-UX, SINIX and linux- Im outwitted > by now..TNX for being helpful, judith > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?003c01c06241$60c9ad40$fa5e78cb>