Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 8 May 2010 10:53:26 -0700
From:      Jack Vogel <jfvogel@gmail.com>
To:        joe <joe@hostedcontent.com>
Cc:        Ian FREISLICH <ianf@clue.co.za>, Fabien Thomas <fabien.thomas@netasq.com>, freebsd-current@freebsd.org
Subject:   Re: igb broken? Unexplained weirdness with intel 82576 nics on a  supermicro board.
Message-ID:  <AANLkTikVu2mfnLXzYEms4RO0toTvBctARq1lQ2ZmnVOT@mail.gmail.com>
In-Reply-To: <4BE599B0.60203@hostedcontent.com>
References:  <4BE565E5.9030505@hostedcontent.com> <4BE5303B.8050409@hostedcontent.com> <4BE529FF.5000008@hostedcontent.com> <C15B47BC-AF5F-4AF4-899C-98155EC5A4D4@netasq.com> <E1OAhhO-00021o-DH@clue.co.za> <E1OAlmh-0002Dj-Mm@clue.co.za> <4BE59434.9070308@hostedcontent.com> <AANLkTikLmEwr15mPz9Hz1kB97dXUNhkOS8R47d68rm1z@mail.gmail.com> <4BE599B0.60203@hostedcontent.com>

next in thread | previous in thread | raw e-mail | index | archive | help
I still am not clear on this system, how many ports are on it, and its an
82576?
Sounds to me like you've proven its not on the box if you can do fine when
its
on its own. So change ports in the switch, as I said, change cables, must be
something in that environment.

Jack


On Sat, May 8, 2010 at 10:04 AM, joe <joe@hostedcontent.com> wrote:

> On 05/08/2010 01:31 PM, Jack Vogel wrote:
>
>> Looks like something to do with system C, you might isolate it, and try
>> a back
>> to back connection with its NICs, change cables, look at BIOS settings,
>> change
>> the slot the nic is in... All just off the top of my head.
>>
>> Jack
>>
>>
>> On Sat, May 8, 2010 at 9:41 AM, joe <joe@hostedcontent.com
>> <mailto:joe@hostedcontent.com>> wrote:
>>
>>    On 05/08/2010 11:17 AM, Ian FREISLICH wrote:
>>
>>        joe wrote:
>>
>>            On 05/08/2010 06:55 AM, Ian FREISLICH wrote:
>>
>>                joe wrote:
>>
>>                           I have just tried your suggeston and it has
>>                    no effect for me ;(
>>
>>
>>                Do you have another brand of NIC that you can try?  At
>>                least that
>>                will isolate whether it's igb(4) or something else.
>>
>>
>>            I will grab a new nic today and try...my options are limited
>>            though.
>>            Here are the nics i can get my hands on
>>
>>            TP-LINK TL-TG3468, 10/100/1000Mbps PCIe Adapter (supported
>>            by fbsd?)
>>
>>
>>        Based on the RTL8168B chip.  Should be supported by the re(4)
>>        driver.
>>
>>            Intel (EXPI9301CT) Gigabit CT Desktop Adapter (yet another
>>            intel nic)
>>
>>
>>        i82574L chip.  Should be supported by the em(4) driver.  I have had
>>        good performance in the past with this driver and less than
>>        satisfactory performance with the igb(4) driver.
>>
>>        That may not be your problem though.  Before you go out and buy,
>>        have a look at the amount of interrupt time your slow machine
>> spends
>>        in 'top' or 'systat -vm'.  systat will also show the interrupt rate
>>        for each driver, perhaps it's not doing interrupt moderation
>>        properly.
>>        This will manifest as more than about a 1000 per second.  There are
>>        loader tunables for the driver to increase the number of transfer
>>        descriptors and to tune interrupt moderation.
>>
>>        You could try running trafshow (port) on the interface while
>>        performing the transfer.  Perhaps promiscuous mode will turn off
>>        some hardware feature that will improve things.  It may however
>>        break hardware vlanning as it does on my 82575GB 4 port igb card.
>>
>>        Ian
>>
>>        --
>>        Ian Freislich
>>
>>
>>    I bought those two cards anyways, im in a rush to figure out this
>>    problem. That being said i am still encountering the exact same
>>    problem regardless on which network card i am running. I am at a
>>    complete loss. I am about to try a raid card to see if the problem
>>    might lay within the onboard sata ports. I did pull the server and
>>    brought it home so that i can test more things quicker.
>>
>>    I am going to try using a raid card instead of the onboard sata
>>    ports and see if i still encounter the same problem. I would love
>>    any suggestions you may have on where to go from here to figure out
>>    where the problem might be.
>>
>>    joe
>>
>>    _______________________________________________
>>    freebsd-current@freebsd.org <mailto:freebsd-current@freebsd.org>
>>
>>    mailing list
>>    http://lists.freebsd.org/mailman/listinfo/freebsd-current
>>    To unsubscribe, send any mail to
>>    "freebsd-current-unsubscribe@freebsd.org
>>    <mailto:freebsd-current-unsubscribe@freebsd.org>"
>>
>>
>>
> I think it might have something to so with the nics / switch, and their
> features. I brought the box home, plugged into my gb switch, and i am able
> to FTP data to the server at around 35MB/sec.
>
> I dont know what would cause this other than some sort of issue with the
> the 3 different types of nics and the switch i am using.
>
> Any suggestions?
>



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?AANLkTikVu2mfnLXzYEms4RO0toTvBctARq1lQ2ZmnVOT>