Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 29 Mar 2004 15:51:40 -0800 (PST)
From:      Julian Elischer <julian@elischer.org>
To:        freebsd-stable@freebsd.org
Subject:   Re: USB2 device
Message-ID:  <Pine.BSF.4.21.0403291550510.29660-100000@InterJet.elischer.org>
In-Reply-To: <1080603100.353.3.camel@fast.mmercer.com>

next in thread | previous in thread | raw e-mail | index | archive | help
plug it in and then run usbdevs -v

Let's see what it sees.

(do you have cam and 'da' and umass all loaded?)




On Mon, 29 Mar 2004, Michael E. Mercer wrote:

> Julian,
> 
> I built the kernel with ehci, it boots and I see another hub using ehci.
> However when I plug in my JumpDrive, it does not get added.
> 
> Michael Mercer
> 
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD 4.9-STABLE #0: Mon Mar 29 18:19:39 EST 2004
>     mmercer@fast.mmercer.com:/usr/obj/usr/src/sys/g49
> Timecounter "i8254"  frequency 1193182 Hz
> CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.83-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
>  
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>   Hyperthreading: 2 logical CPUs
> real memory  = 1072889856 (1047744K bytes)
> avail memory = 1039880192 (1015508K bytes)
> Programming 24 pins in IOAPIC #0
> IOAPIC #0 intpin 2 -> irq 0
> IOAPIC #0 intpin 17 -> irq 10
> IOAPIC #0 intpin 18 -> irq 5
> IOAPIC #0 intpin 19 -> irq 11
> FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs
>  cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
>  cpu1 (AP):  apic id:  1, version: 0x00050014, at 0xfee00000
>  io0 (APIC): apic id:  2, version: 0x00178020, at 0xfec00000
> Preloaded elf kernel "kernel" at 0xc042b000.
> Warning: Pentium 4 CPU: PSE disabled
> Pentium Pro MTRR support enabled
> md0: Malloc disk
> Using $PIR table, 12 entries at 0xc00f50e0
> apm0: <APM BIOS> on motherboard
> apm0: found APM BIOS v1.2, connected at v1.2
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcib0: <Host to PCI bridge> on motherboard
> pci0: <PCI bus> on pcib0
> agp0: <Intel 82875P host to AGP bridge> mem 0xd0000000-0xdfffffff at
> device 0.0 on pci0
> pcib1: <PCI to PCI bridge (vendor=8086 device=2579)> at device 1.0 on
> pci0
> pci1: <PCI bus> on pcib1
> pci1: <NVidia model 0322 graphics accelerator> at 0.0 irq 10
> pcib2: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on
> pci0
> pci2: <PCI bus> on pcib2
> em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port
> 0xcf80-0xcf9f mem 0xfe9e0000-0xfe9fffff irq 5 at device 1.0 on pci2
> em0:  Speed:N/A  Duplex:N/A
> uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xef00-0xef1f
> irq 10 at device 29.0 on pci0
> usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xef20-0xef3f
> irq 11 at device 29.1 on pci0
> usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xef40-0xef5f
> irq 5 at device 29.2 on pci0
> usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
> usb2: USB revision 1.0
> uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xef80-0xef9f
> irq 10 at device 29.3 on pci0
> usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
> usb3: USB revision 1.0
> uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebfffff irq
> 11 at device 29.7 on pci0
> ehci_pci_attach: companion usb0
> ehci_pci_attach: companion usb1
> ehci_pci_attach: companion usb2
> ehci_pci_attach: companion usb3
> usb4: EHCI version 1.0
> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
> usb4: <EHCI (generic) USB 2.0 controller> on ehci0
> usb4: USB revision 2.0
> uhub4: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub4: 8 ports with 8 removable, self powered
> uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00,
> addr 2
> uhub5: 4 ports with 4 removable, self powered
> uhub5: cannot open interrupt pipe
> device_probe_and_attach: uhub5 attach returned 6
> uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00,
> addr 2
> uhub5: 4 ports with 4 removable, self powered
> uhub5: cannot open interrupt pipe
> device_probe_and_attach: uhub5 attach returned 6
> pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on
> pci0
> pci3: <PCI bus> on pcib3
> fwohci0: <VIA VT6306> port 0xdc00-0xdc7f mem 0xfeaff800-0xfeafffff irq 5
> at device 3.0 on pci3
> fwohci0: OHCI version 1.0 (ROM=1)
> fwohci0: No. of Isochronous channel is 8.
> fwohci0: EUI64 00:e0:18:00:00:58:2a:e6
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:e0:18:58:2a:e6
> fwohci0: Initiate bus reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on
> pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH5 ATA100 controller> port
> 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 irq 0 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 10
> pcm0: <Intel ICH5 (82801EB)> port 0xee80-0xeebf,0xe800-0xe8ff mem
> 0xfebff400-0xfebff4ff,0xfebff800-0xfebff9ff irq 10 at device 31.5 on
> pci0
> pcm0: <Analog Devices AD1985 AC97 Codec>
> orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0
> pmtimer0 on isa0
> fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
> isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: model IntelliMouse Explorer, device ID 4
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> ppc0: FIFO with 16/16/9 bytes threshold
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> APIC_IO: Testing 8254 interrupt delivery
> APIC_IO: routing 8254 via IOAPIC #0 intpin 2
> SMP: AP CPU #1 Launched!
> ad0: 39205MB <Maxtor 6E040L0> [79656/16/63] at ata0-master UDMA100
> ad3: 194481MB <Maxtor 6Y200P0> [395136/16/63] at ata1-slave UDMA100
> acd0: DVD-R <OPTORITEDVD RW DD0203> at ata1-master PIO4
> Mounting root from ufs:/dev/ad3s1a
> em0: Link is up 100 Mbps Full Duplex
> em0: Link is up 100 Mbps Full Duplex
> 
> 
> 



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0403291550510.29660-100000>