Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 19 Nov 2011 18:07:58 -0600
From:      Nathan Whitehorn <nwhitehorn@freebsd.org>
To:        nevtic@tx.net
Cc:        freebsd-current@freebsd.org
Subject:   Re: 9.0-RC2 - bsdinstall miscount of remaining diskspace after partition deletion.
Message-ID:  <4EC844DE.7020003@freebsd.org>
In-Reply-To: <alpine.BSF.2.00.1111181304250.3186@area51.tx.net>
References:  <alpine.BSF.2.00.1111181304250.3186@area51.tx.net>

next in thread | previous in thread | raw e-mail | index | archive | help
On 11/18/11 17:09, nevtic@tx.net wrote:
>
> If you are performating a manual partion in 9.0-RC2 bsdinstall and you 
> delete any created partition except the most recently created one, the 
> total remaining space will be miscalculated.  Reproducable as shown 
> below.
>
> Workaround:  if you delete a partition that is not the last partition 
> that was created, delete all partitions created after that partition 
> before continuing.  Order does not seem to be important.
>
> The results are similar with other hard drive sizes, with the i386 or 
> amd64 distributions, and with either 9.0-RC2 or 9.0-RC1 (I did not go 
> back and check install discs prior to RC1)
>
> Reproducing the miscount:
>
> A 114 GB drive is used for this example:
>
>   Select Manual Partitioning
>
>   Perform the first Create on the drive and select GPT
>
>   Creating the first partition:  "Add Partition" "size" shows 114GB
>
>     Change size to 4GB, set mountpoint to  /  and tab to OK
>       (agree to the boot partition creation)
>
>   Create a second partition: "Add Partition" "size" shows 110GB
>
>     Adjust size to 10GB, set mountpoint to  /usr and tab to OK
>
>   Create a third partition: "Add Partition" "size" shows 100GB
>
>     Adjust size to 20GB, set mountpoint to /var, and tab to OK
>
>   Create a 4th partition: "size" shows 80GB remaining
>
>     Adjust size to 40GB, set mountpoint to /data,  and tab to OK.
>
> There is 40 GB remaining on the drive.  Now change the size of /var.  
> First, delete the currently configured /var partition.
>
> In the Partition Editor, adding up all the lines on the screen shows 
> 54GB (plus a 64K boot) as allocated, so there should now be 60GB 
> remaining.  But the deleted /var space has not been added back into 
> the total.
>
> Select Create again: "Add Partition" "size" shows 40GB
>
>    Adjust size to 30GB, set mountpoint as /var, tab to OK
>
> A subsequent "Create" will show that 20GB is remaining, rather than 
> the actual remaining 30GB.  Selecting any size 20GB or larger for 
> /home will give you a 20GB partition, and then an additional create 
> will show the 10GB.

This isn't a bug. The partitions are laid out on disk already, and, 
because you deleted one in the middle, the largest *contiguous* block of 
free space is 20GB, which is what is shown and the maximum it is 
possible to create. That's why you can make one 20 GB partition and one 
10 GB partition, but not a single 30 GB one.
-Nathan



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4EC844DE.7020003>