Date: Wed, 15 Jan 2003 11:28:29 +0800 From: Reed Lai <reed@wingeer.org> To: FreeBSD Questions <freebsd-questions@FreeBSD.ORG> Subject: Re: SiS Ethernet with RTL8201L on FreeBSD 4.7 Message-ID: <20030115032829.GA521@owle.wingeer.org> In-Reply-To: <01c101c2bc3c$05445860$0a0aa8c0@dweebsoft.com> References: <20030114094122.887A743F18@mx1.FreeBSD.org> <005801c2bbb4$0cb410f0$0a0aa8c0@dweebsoft.com> <20030114104224.GA201@owle.wingeer.org> <01c101c2bc3c$05445860$0a0aa8c0@dweebsoft.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Done, but still no PHY with the same message... On Tue, Jan 14, 2003 at 06:15:48PM -0800, Dax Eckenberg wrote: > just as a test... also add miibus0 > > > ----- Original Message ----- > From: "Reed Lai" <reed@wingeer.org> > To: "FreeBSD Questions" <freebsd-questions@FreeBSD.ORG> > Sent: Tuesday, January 14, 2003 2:42 AM > Subject: Re: SiS Ethernet with RTL8201L on FreeBSD 4.7 > > > > Yes, there is a "device miibus" in my configuration file, > > or the compiling will be failed. > > > > On Tue, Jan 14, 2003 at 02:02:29AM -0800, Dax Eckenberg wrote: > > > Have you tried adding.... > > > > > > device miibus0 > > > > > > to the GENERIC kernel config? > > > > > > # cd /usr/src/sys/i386/conf > > > # cp GENERIC MIITEST > > > # echo device miibus0 >> MIITEST > > > # config ./MIITEST > > > # cd ../../compile/MIITEST > > > # make depend && make > > > > > > if all goes well... > > > > > > make install > > > > > > > > > > > > ----- Original Message ----- > > > From: <reed@wingeer.org> > > > To: <undisclosed-recipients:> > > > Sent: Tuesday, January 14, 2003 1:41 AM > > > Subject: SiS Ethernet with RTL8201L on FreeBSD 4.7 > > > > > > > > > > Seniors, > > > > > > > > I installed the FreeBSD/i386 4.7 into a PC that uses SiS chips > > > > set with a RTL8201L PHY. The system failed to drive the ethernet > > > > adapter with messages > > > > > > > > ==== > > > > .. > > > > sis0: <SiS 900 10/100BaseTX> port 0xa000-0xa0ff mem > > > > 0xe6000000-0xe6000fff irq 3 at device 3.0 pci0 > > > > sis0: Ethernet address: 00:e0:18:de:a9:ff > > > > sis0: MII without any PHY! > > > > device_probe_and_attach: sis0 attach returned 6 > > > > .. > > > > ==== > > > > > > > > I read many articles from Use-net but there seemed no solution for > > > > this problem. > > > > > > > > Any help will be appreciated. > > > > -- > > > > Reed Lai > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > > > with "unsubscribe freebsd-questions" in the body of the message > > > > > > > > -- > > Reed Lai | http://bv4qo.wingeer.org/ | ICQ 19080719(H) 64518529(W) > > GnuPG (DSA/ElGamal) C4CBF333 ,, Reed Lai (BV4QO) <reed@wingeer.org> > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message > > -- Reed Lai | http://bv4qo.wingeer.org/ | ICQ 19080719(H) 64518529(W) GnuPG (DSA/ElGamal) C4CBF333 ,, Reed Lai (BV4QO) <reed@wingeer.org> To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030115032829.GA521>