Date: Mon, 7 Oct 2013 17:47:31 -0700 From: Kurt Buff <kurt.buff@gmail.com> To: pyunyh@gmail.com Cc: freebsd-net@freebsd.org Subject: Re: Problem with Lenovo SL500 Message-ID: <CADy1Ce6=GrufDhXUdkbvzY6MR_8-bKmqJEM_JdHG%2BSx%2BFQp0BQ@mail.gmail.com> In-Reply-To: <20131008003359.GA3162@michelle.cdnetworks.com> References: <CADy1Ce73mrmTiA6sX34HAsa0ihdOYXAEtsyEYXWYBKfS1D_XpQ@mail.gmail.com> <20131008003359.GA3162@michelle.cdnetworks.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Wow. What a rookie mistake. :( 'ifconfig re0 up' brought it right up. I'll add that line to rc.conf as 'ifconfig_re0="UP"' Thanks, Kurt On Mon, Oct 7, 2013 at 5:33 PM, Yonghyeon PYUN <pyunyh@gmail.com> wrote: > On Mon, Oct 07, 2013 at 03:14:58PM -0700, Kurt Buff wrote: >> All, >> >> This machine has for its wired port a RealTek unit: >> >> re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port >> 0xe800-0xe8ff mem 0xfcfff000-0xfcffffff,0xfcfe0000-0xfcfeffff irq 19 >> at device 0.0 on pci12 >> re0: Using 1 MSI-X message >> re0: ASPM disabled >> re0: Chip rev. 0x3c000000 >> re0: MAC rev. 0x00400000 >> miibus0: <MII bus> on re0 >> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 >> rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, >> 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, >> 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, >> 1000baseT-FDX-flow-master, auto, auto-flow >> re0: Ethernet address: 00:26:18:45:77:51 >> >> >> I've got wireless working for iwn (thanks Adrian!), and I'm trying to >> use the wired NIC (re0) as an unnumbered port to monitor a mirror port >> on an HP switch. However, when I connect it, it shows up as only >> 10mbit, half-duplex on the switch, and it refuses to send packets. >> >> I've tried 'ifconfig re0 media 1000baseT -mediaopt full-duplex' >> >> with no particular luck, as it shows the following >> >> re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 >> options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> >> ether 00:26:18:45:77:51 >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> media: Ethernet 1000baseT (10baseT/UTP <half-duplex>) >> status: active >> >> I get no output from 'tcpdump -npi re0'. I get link light, and it >> worked great on re0 when I did the install for FreeBSD, but no joy for >> capturing packets from the switch. > > It seems you didn't UP the interface. And you may have to put the > interface into promiscuous mode to capture all packets(i.e. remove > -p option). > >> >> Anyone have some thoughts to share on this? Yes, I tried using a new >> cable, too... >> >> Kurt
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CADy1Ce6=GrufDhXUdkbvzY6MR_8-bKmqJEM_JdHG%2BSx%2BFQp0BQ>