Date: Sun, 28 Dec 2003 22:57:26 +0100 From: Sven Esbjerg <esbjerg@xbsd.net> To: freebsd-current@freebsd.org Subject: Re: 5.2-RC oerrs and collisions on dc0 Message-ID: <20031228215726.GA6955@gosling.home.xbsd.net> In-Reply-To: <200312280049.50629.dejan.lesjak@ijs.si> References: <200312280049.50629.dejan.lesjak@ijs.si>
next in thread | previous in thread | raw e-mail | index | archive | help
--opJtzjQTFsWo+cga Content-Type: text/plain; charset=us-ascii Content-Disposition: inline On Sun, Dec 28, 2003 at 12:49:50AM +0100, Dejan Lesjak wrote: > > I tried 5.2-RC2 on alpha and netstat -i keeps showing oerrs and collisions on > 5.1-RELEASE. > This has been reported by Andy Farkas here: > http://docs.freebsd.org/cgi/getmsg.cgi?fetch=2200233+0+archive/2003/freebsd-current/20031116.freebsd-current I'm seeing the same on 5.2-release on sparc. Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Coll dc0 1500 <Link#5> 80:00:ca:c8:25:b8 2286 0 1810 0 900 dc0 1500 10.0.1/24 10.0.1.1 853 - 521 - - dc0 1500 fe80:5::8200: fe80:5::8200:caff 0 - 2 - - dc1 1500 <Link#6> 80:00:ca:c8:26:b8 41858 0 56874 0 3495 dc1 1500 10.0.2/24 10.0.2.1 305 - 385 - - dc1 1500 fe80:6::8200: fe80:6::8200:caff 0 - 4 - - dc2 1500 <Link#7> 80:00:ca:c8:27:b8 0 0 0 0 0 dc2 1500 10.0.3/24 10.0.3.1 0 - 0 - - dc2 1500 fe80:7::8200: fe80:7::8200:caff 0 - 3 - - dc3 1500 <Link#8> 80:00:ca:c8:28:b8 0 0 0 0 0 dc3 1500 10.0.4/24 10.0.4.1 0 - 0 - - dc3 1500 fe80:8::8200: fe80:8::8200:caff 0 - 4 - - Also this was logged to the console when transferring files: ultra10# dc1: TX underrun -- increasing TX threshold dc1: TX underrun -- increasing TX threshold ultra10# dc1: TX underrun -- increasing TX threshold The card is a quad port D-Link (can't remember the model number other than it's not 580). pciconf -lv and dmesg attached. Regards Sven Esbjerg --opJtzjQTFsWo+cga Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="pciconf.out" pcib1@pci0:1:1: class=0x060400 card=0x00000000 chip=0x5000108e rev=0x13 hdr=0x01 vendor = 'Sun Microsystems' device = 'SME2411 UltraSPARC-IIi Advanced PCI Bridge' class = bridge subclass = PCI-PCI pcib2@pci0:1:0: class=0x060400 card=0x00000000 chip=0x5000108e rev=0x13 hdr=0x01 vendor = 'Sun Microsystems' device = 'SME2411 UltraSPARC-IIi Advanced PCI Bridge' class = bridge subclass = PCI-PCI ebus0@pci1:1:0: class=0x068000 card=0x00000000 chip=0x1000108e rev=0x01 hdr=0x00 vendor = 'Sun Microsystems' device = 'SPARC EBUS PCIO PCI I/O Controller' class = bridge subclass = PCI-unknown hme0@pci1:1:1: class=0x020000 card=0x00000000 chip=0x1001108e rev=0x01 hdr=0x00 vendor = 'Sun Microsystems' device = 'PCIO Happy Meal Ethernet' class = network subclass = ethernet none0@pci1:2:0: class=0x030000 card=0x00000000 chip=0x47501002 rev=0x5c hdr=0x00 vendor = 'ATI Technologies' device = 'Rage 3D Pro PCI Graphics Accelerator' class = display subclass = VGA atapci0@pci1:3:0: class=0x01018f card=0x06461095 chip=0x06461095 rev=0x03 hdr=0x00 vendor = 'Silicon Image Inc (Was: CMD Technology Inc)' device = 'PCI-0646 EIDE Adapter (Single FIFO)' class = mass storage subclass = ATA xl0@pci2:1:0: class=0x020000 card=0x100010b7 chip=0x920010b7 rev=0x74 hdr=0x00 vendor = '3COM Corp, Networking Division' device = '3C905C-TX Fast EtherLink for PC Management NIC' class = network subclass = ethernet xl1@pci2:2:0: class=0x020000 card=0x905510b7 chip=0x905510b7 rev=0x30 hdr=0x00 vendor = '3COM Corp, Networking Division' device = '3C905B-TX Fast Etherlink 10/100 PCI TX NIC' class = network subclass = ethernet xl2@pci2:3:0: class=0x020000 card=0x00000000 chip=0x905010b7 rev=0x00 hdr=0x00 vendor = '3COM Corp, Networking Division' device = '3C905-TX Fast Etherlink XL PCI 10/100' class = network subclass = ethernet pcib3@pci2:4:0: class=0x060400 card=0x000000dc chip=0x00241011 rev=0x03 hdr=0x01 vendor = 'Digital Equipment Corporation' device = '21151/2 PCI to PCI Bridge' class = bridge subclass = PCI-PCI dc0@pci3:4:0: class=0x020000 card=0x11121186 chip=0x00191011 rev=0x41 hdr=0x00 vendor = 'Digital Equipment Corporation' device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' class = network subclass = ethernet dc1@pci3:5:0: class=0x020000 card=0x11121186 chip=0x00191011 rev=0x41 hdr=0x00 vendor = 'Digital Equipment Corporation' device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' class = network subclass = ethernet dc2@pci3:6:0: class=0x020000 card=0x11121186 chip=0x00191011 rev=0x41 hdr=0x00 vendor = 'Digital Equipment Corporation' device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' class = network subclass = ethernet dc3@pci3:7:0: class=0x020000 card=0x11121186 chip=0x00191011 rev=0x41 hdr=0x00 vendor = 'Digital Equipment Corporation' device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' class = network subclass = ethernet --opJtzjQTFsWo+cga Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="dmesg.out" Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-BETA #0: Mon Dec 22 20:37:54 CET 2003 root@ultra10.home.xbsd.net:/usr/src/sys/sparc64/compile/ULTRA10 Preloaded elf kernel "/boot/kernel/kernel" at 0xc04b0000. Timecounter "tick" frequency 333000000 Hz quality 0 real memory = 268435456 (256 MB) avail memory = 248119296 (236 MB) cpu0: Sun Microsystems UltraSparc-IIi Processor (333.00 MHz CPU) nexus0: <OpenFirmware Nexus device> pcib0: <U2P UPA-PCI bridge> on nexus0 pcib0: Sabre, impl 0, version 0, ign 0x7c0, bus A pcib0: [FAST] pcib0: [FAST] DVMA map: 0xc0000000 to 0xc3ffffff pci0: <OFW PCI bus> on pcib0 pcib1: <APB PCI-PCI bridge> at device 1.1 on pci0 pci1: <OFW PCI bus> on pcib1 ebus0: revision 0x01 ebus0: <PCI-EBus2 bridge> mem 0xf1000000-0xf17fffff,0xf0000000-0xf0ffffff at device 1.0 on pci1 ebus0: <auxio> addr 0x140072f000-0x140072f003,0x140072c000-0x140072c003,0x140072a000-0x140072a003,0x1400728000-0x1400728003,0x1400726000-0x1400726003 (no driver attached) ebus0: <power> addr 0x1400724000-0x1400724003 irq 37 (no driver attached) ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached) sab0: <Siemens SAB 82532 v3.2> addr 0x1400400000-0x140040007f irq 43 on ebus0 sab0: [FAST] sabtty0: <ttya> on sab0 sabtty0: console 9600,8,n,1,- sabtty1: <ttyb> on sab0 ebus0: <su> addr 0x14003083f8-0x14003083ff irq 41 (no driver attached) ebus0: <su> addr 0x14003062f8-0x14003062ff irq 42 (no driver attached) ebus0: <ecpp> addr 0x1400700000-0x140070000f,0x140030015c-0x140030015d,0x14003043bc-0x14003043cb irq 34 (no driver attached) ebus0: <fdthree> addr 0x1400720000-0x1400720003,0x1400706000-0x140070600f,0x14003023f0-0x14003023f7 irq 39 (no driver attached) eeprom0: <EBus EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0 eeprom0: model mk48t59 eeprom0: hostid 80a71ffc ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no driver attached) ebus0: <SUNW,CS4231> addr 0x1400722000-0x1400722003,0x1400704000-0x140070400f,0x1400702000-0x140070200f,0x1400200000-0x14002000ff irq 36,35 (no driver attached) hme0: <Sun HME 10/100 Ethernet> mem 0xe0000000-0xe0007fff at device 1.1 on pci1 hme0: Ethernet address: 08:00:20:a7:1f:fc miibus0: <MII bus> on hme0 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci1: <display, VGA> at device 2.0 (no driver attached) atapci0: <CMD 646 WDMA2 controller> port 0xc00020-0xc0002f,0xc00018-0xc0001b,0xc00010-0xc00017,0xc00008-0xc0000b,0xc00000-0xc00007 at device 3.0 on pci1 atapci0: [MPSAFE] ata2: at 0xc00000 on atapci0 ata2: [MPSAFE] ata3: at 0xc00010 on atapci0 ata3: [MPSAFE] pcib2: <APB PCI-PCI bridge> at device 1.0 on pci0 pci2: <OFW PCI bus> on pcib2 xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x2000-0x207f mem 0x200000-0x20007f at device 1.0 on pci2 xl0: Ethernet address: 00:01:02:0d:e7:72 miibus1: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus1 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: <3Com 3c905B-TX Fast Etherlink XL> port 0x2080-0x20ff mem 0x202000-0x20207f at device 2.0 on pci2 xl1: Ethernet address: 00:10:5a:f6:35:56 miibus2: <MII bus> on xl1 xlphy1: <3Com internal media interface> on miibus2 xlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl2: <3Com 3c905-TX Fast Etherlink XL> port 0x2400-0x243f at device 3.0 on pci2 xl2: Ethernet address: 00:60:08:0c:1b:2f miibus3: <MII bus> on xl2 nsphy1: <DP83840 10/100 media interface> on miibus3 nsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pcib3: <OFW PCI-PCI bridge> at device 4.0 on pci2 pci3: <OFW PCI bus> on pcib3 dc0: <Intel 21143 10/100BaseTX> port 0x1000-0x107f mem 0x100000-0x1003ff at device 4.0 on pci3 pcib3: slot 4 INTA is routed to irq 28 dc0: Ethernet address: 80:00:ca:c8:25:b8 miibus4: <MII bus> on dc0 ukphy0: <Generic IEEE 802.3u media interface> on miibus4 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto dc1: <Intel 21143 10/100BaseTX> port 0x1080-0x10ff mem 0x102000-0x1023ff at device 5.0 on pci3 pcib3: slot 5 INTA is routed to irq 29 dc1: Ethernet address: 80:00:ca:c8:26:b8 miibus5: <MII bus> on dc1 ukphy1: <Generic IEEE 802.3u media interface> on miibus5 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto dc2: <Intel 21143 10/100BaseTX> port 0x1400-0x147f mem 0x104000-0x1043ff at device 6.0 on pci3 pcib3: slot 6 INTA is routed to irq 30 dc2: Ethernet address: 80:00:ca:c8:27:b8 miibus6: <MII bus> on dc2 ukphy2: <Generic IEEE 802.3u media interface> on miibus6 ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto dc3: <Intel 21143 10/100BaseTX> port 0x1480-0x14ff mem 0x106000-0x1063ff at device 7.0 on pci3 pcib3: slot 7 INTA is routed to irq 31 dc3: Ethernet address: 80:00:ca:c8:28:b8 miibus7: <MII bus> on dc3 ukphy3: <Generic IEEE 802.3u media interface> on miibus7 ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto Timecounters tick every 10.000 msec GEOM: create disk ad0 dp=0xfffff8001fb8f6a0 ad0: 8693MB <ST39140A> [17662/16/63] at ata2-master WDMA2 GEOM: create disk ad1 dp=0xfffff8001fb8f4a0 ad1: 8693MB <ST39140A> [17662/16/63] at ata2-slave WDMA2 acd0: CDRW <CRD-8322B> at ata3-master PIO4 Mounting root from ufs:/dev/ad0a pflog: $Name: $ pfsync: $Name: $ in6_ifattach: pflog0 is not multicast capable, IPv6 not enabled in6_ifattach: pfsync0 is not multicast capable, IPv6 not enabled pflog0: promiscuous mode enabled pf: $Name: $ dc1: TX underrun -- increasing TX threshold dc1: TX underrun -- increasing TX threshold dc1: TX underrun -- increasing TX threshold --opJtzjQTFsWo+cga--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20031228215726.GA6955>