Date: Mon, 3 Dec 2001 18:52:52 -0700 From: Chad David <davidc@acns.ab.ca> To: freebsd-stable@freebsd.org Subject: SMP beeping Message-ID: <20011203185252.A336@colnta.acns.ab.ca>
next in thread | raw e-mail | index | archive | help
I upgraded one of my servers to stable this afternoon only to find that if SMP is enabled the pc speaker starts to beep on and off in a somewhat random pattern forever.... If I boot a GENERIC kernel without SMP the beeping goes away, if I then only add the two SMP related lines the beeping starts again. I've narrowed it down that the time the second cpu is started is the time the beeping begins. What is strange that if I then boot into a GENERIC kernel it will continue to beep at strange points (the bios netboot prompt, just prior to the loader count down, at the copywrite printout etc.), but somewhere during the boot it fixes itself. If I reboot into GENERIC again all is normal (no strange beeps). Does this "ring a bell" with anybody? Here is the dmesg for what its worth: Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.4-STABLE #1: Mon Dec 3 18:48:58 MST 2001 root@colnta:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (1004.52-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 1073725440 (1048560K bytes) avail memory = 1041096704 (1016696K bytes) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc0499000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 7 entries at 0xc00f12d0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard IOAPIC #0 intpin 16 -> irq 2 IOAPIC #0 intpin 19 -> irq 10 pci0: <PCI bus> on pcib0 pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib2 pci1: <ATI Mach64-GB graphics accelerator> at 0.0 irq 2 isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C686 ATA100 controller> port 0xb800-0xb80f at device 4.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <NVidia model 0110 graphics accelerator> at 12.0 irq 2 xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa800-0xa87f mem 0xeb800000-0xeb80007f irq 10 at device 13.0 on pci0 xl0: Ethernet address: 00:01:02:47:d5:14 miibus0: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pcib1: <Host to PCI bridge> on motherboard pci2: <PCI bus> on pcib1 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: failed to get data. psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: IEEE1284 device found /NIBBLE/ECP Probing for PnP devices on ppbus0: ppbus0: <Hewlett-Packard HP LaserJet 1200> PRINTER PJL,MLC,PCL,PCLXL,POSTSCRIPT plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 SMP: AP CPU #1 Launched! ad0: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata0-master tagged UDMA100 ad1: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata0-slave tagged UDMA100 ad2: 9765MB <FUJITSU MPC3102AT E> [19841/16/63] at ata1-master UDMA33 acd0: CDROM <LG CD-ROM CRD-8522B> at ata1-slave using PIO4 Mounting root from ufs:/dev/ad2s1a -- Chad David davidc@acns.ab.ca ACNS Inc. Calgary, Alberta Canada -- Chad David davidc@acns.ab.ca ACNS Inc. Calgary, Alberta Canada To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20011203185252.A336>