Date: Wed, 21 Feb 2001 15:44:57 -0500 From: "Marc Ramirez" <mrami4@hotmail.com> To: questions@freebsd.org Subject: A couple of questions - FreeBSD 4.2-RELEASE Message-ID: <F98RLNTaFagA34pfRS800002847@hotmail.com>
next in thread | raw e-mail | index | archive | help
Quick, and to the point: 1) I assume that support for a vinum partition on a bootable disk is absent... 2) I got an old P-120 laptop (Zenith Z-NOTE GT) I was trying to put FBSD 4.2-RELEASE on, and I've been having the following problem: The hard drive is a regular IDE drive, but the install kernel seems to have problems with the way the controller is doing its PCI thing. Here's what I get in the boot message: avail memory = 10076160 (9840K bytes) Preloaded elf kernel "kernel" at 0xc065d000. Preloaded mfs_root "/mfsroot" at 0xc065d084. Intel Pentium detected, installing workaround for F00F bug md0: Preloaded image </mfsroot> 2949120 bytes at 0xc038bcd8 md1: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 isab0: <PCI to ISA bridge (vendor=1045 device=c558) at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <Chips & Technologies 65548 SVGA controller> at 5.0 atapci0: <Generic PCI ATA controller> port 0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 6.0 on pci0 atapci0: Busmastering DMA not supported ata2: at 0x1f0 on atapci0 ata2: unable to allocate interrupt device_probe_and_attach: ata2 attach returned 6 fdc0: cannot reserve I/O port range atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 moouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa000-0xbfff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> pcic0: <Vadem 469> at port 0x3e0 iomem 0xd0000 on isa0 pcic0: Polling mode pccard0: <PC Card bus -- kludge version> on pcic0 pccard1: <PC Card bus -- kludge version> on pcic0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/15 bytes threshold plip0: <PLIP network interface> on ppbus0 no devsw (majdev2 bootdev=0xa0500002) Is there any way I can force ata0 to attach at the normal ISA address (and then do the same for fdc0)? Or am I going to have to turn off PCI amd make my own install disk? Many thanks, Marc. _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?F98RLNTaFagA34pfRS800002847>