Date: Wed, 22 Jan 1997 18:40:27 +0000 From: "Coi Giovanni" <Coi_Giovanni@prometeo.it> To: freebsd-question@FreeBSD.org, freebsd-scsi@FreeBSD.org Subject: AHA-1522A and DAT Data phase error Message-ID: <199701221753.SAA24778@prometeo.prometeo.it>
next in thread | raw e-mail | index | archive | help
Hello,
I have a SONY SDT-5200 3.26 tape backup (DAT) which I am trying
to run. The SCSI controller is a AHA-1522A (ISA bus)
when I try to write on tape (with dump for example) I get
the following error messages on console:
st0(aic0:5:0): ABORTED COMMAND info:4 asc:4b,0 Data phase error
st0(aic0:5:0): HARDWARE FAILURE info:14 asc:44,0 Internal
target failure
st0(aic0:5:0): HARDWARE FAILURE info:14 asc:44,0 Internal target
failure
st0(aic0:5:0): HARDWARE FAILURE info:1 asc:44,0 Internal
target failure
the dump command is
dump 0uBbf 2000000 10 /dev/rst0 /dev/wd0a
but I try also with
dump 0uBbf 2000000 10 /dev/rst0 /
whit the same results
and this is the output of dump on stderr:
DUMP: Date of this level 0 dump: Wed Jan 22 13:52:54 1997
DUMP: Date of last level 0 dump: the epoch
DUMP: Dumping /dev/rwd0a (/) to /dev/rst0
DUMP: mapping (Pass I) [regular files]
DUMP: mapping (Pass II) [directories]
DUMP: estimated 15086 tape blocks on 0.01 tape(s).
DUMP: dumping (Pass III) [directories]
DUMP: dumping (Pass IV) [regular files]
... error messages on console....
DUMP: End of tape detected
DUMP: Closing /dev/rst0
DUMP: Change Volumes: Mount volume #2
DUMP: Is the new volume mounted and ready to go?: ("yes" or "no")
I reply no
DUMP: Do you want to abort?: ("yes" or "no")
I reply yes
DUMP: The ENTIRE dump is aborted.
Note:
a) after I run the dump command after signaling
DUMP: dumping (Pass IV) [reguler files]
the system freeze. It do not respond at console, no on other
telnet session, no on other vitrual console. After it finish
(with error) all return to normal state.
b) I have tryed the following command:
tar cvf /dev/rst0 /etc
and it goes. Then I can run also
tar tvf /dev/rst0
and see the correct listing of etc's file.
I think it was because there are few data in /etc.
c) the _same_ DAT works fine when I connect it to a
windows NT 4.0 box (but with a SCSI controller
more quick, an PCI Adaptec AHA-2940
d) as you can see from the startup log (below) I have also
a SCSI CDROM that work fine (I have copied with success
a file of about 10Mbyte from it).
Anyone has some suggestions?
Please reply directly to me or on freebsd-question list.
TIA.
Follow my system configuration parameter:
---------------------------------------------------------------
controller aic0 at isa? port 0x140 bio irq 10 vector aicintr
controller scbus0 at aic0 # Single bus device
disk sd0 at scbus0 target 4 unit 0
tape st0 at scbus0 target 5 unit 0
device cd0 at scbus0 target 3 unit 0
options SCSI_DELAY=30
options SCSIDEBUG
---------------------------------------------------------------
Follow my startup log
-----------------------------------------------------------
FreeBSD 2.1.5-RELEASE #0: Wed Jan 22 15:56:04 MET 1997
CPU: i486DX (486-class CPU)
real memory = 16777216 (16384K bytes)
avail memory = 14835712 (14488K bytes)
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA mono <4 virtual consoles, flags=0x0>
ed0 at 0x340-0x35f irq 5 on isa
ed0: address 00:00:1b:3a:c4:88, type NE2000 (16 bit)
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16450
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16450
aic0 at 0x140-0x15f irq 10 on isa
aic0 waiting for scsi devices to settle
(aic0:3:0): "NEC CD-ROM DRIVE:501 2.2" type 5 removable SCSI 2
cd0(aic0:3:0): CD-ROM cd present.[328201 x 2048 byte records]
(aic0:4:0): "IBM MTA-3230TC2210!B 0" type 7 removable SCSI 2
uk0(aic0:4:0): Unknown
(aic0:5:0): "SONY SDT-5200 3.26" type 1 removable SCSI 2
st0(aic0:5:0): Sequential-Access density code 0x13, 512-byte blocks,
write-enabled wdc0 at 0x1f0-0x1f7 irq 14 flags 0x80008000 on isa
wdc0: unit 0 (wd0): <WDC AC2850F> wd0: 814MB (1667232 sectors), 1654
cyls, 16 heads, 63 S/T, 512 B/S wdc0: unit 1 (wd1): <WDC AC2540H>
wd1: 515MB (1056384 sectors), 1048 cyls, 16 heads, 63 S/T, 512 B/S
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa fdc0: NEC 765 fd0: 1.44MB
3.5in mcd0: type Mitsumi FX001D, version info: D 2 mcd0 at 0x320-
0x323 irq 11 on isa npx0 on motherboard npx0: INT 16 interface
-----------------------------------------------------------
----------------------------------------------------------
Prometeo srl - Progetti e Metodologie Informatiche
Internet Services Provider
Coi Giovanni
Voice : +39 (041)5701366 Via Giudecca 15
Fax : +39 (041)5701005 30035 MIRANO (VE) - ITALY
e-mail: coi@prometeo.it http://www.prometeo.it
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199701221753.SAA24778>