Date: Sun, 30 Apr 2006 08:50:18 GMT From: Eugene Grosbein <eugen@grosbein.pp.ru> To: freebsd-bugs@FreeBSD.org Subject: Re: kern/91408 : [irq] ata(4) failure: SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER Will Robinson !! Message-ID: <200604300850.k3U8oIfa015644@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR kern/91408; it has been noted by GNATS. From: Eugene Grosbein <eugen@grosbein.pp.ru> To: John Baldwin <jhb@freebsd.org> Cc: bug-followup@freebsd.org, lightsquid@logvinov.com Subject: Re: kern/91408 : [irq] ata(4) failure: SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER Will Robinson !! Date: Sun, 30 Apr 2006 16:44:32 +0800 On Sat, Apr 29, 2006 at 10:54:09PM -0400, John Baldwin wrote: > > With 6.1-RC of today I have the same sympthoms as with 5.4-RELEASE > > (http://www.freebsd.org/cgi/query-pr.cgi?pr=kern/80815): > > > > 1) machine suffers from ATA timeouts if ACPI is fully enabled; > > 2) debug.acpi.disable="pci_link" in /boot/loader.conf eliminates the > > problem. > > > > So, Soren seems to be right: this is interrupt routing problem > > and not ATA problem. > > > > The question is: should I consider the workaround mentioned above as > > solution? What will I miss if I keep debug.acpi.disable="pci_link" forever? > > I think it's dangerous What kind of trouble I am "asking for" while using debug.acpi.disable="pci_link"? > and that you should just disable ACPI altogether if you wish to do that. I think I do not wish that :-) This machive has four OS now: FreeBSD 4.11-RELEASE (uses APM to turn power off), Windows 98SE and Windows XP SP2 (use ACPI, no problems with it). Would I be allowed to turn power off with 6.1 without ACPI enabled? Would it be possible not only for 'shutdown -p', but for ACPI power button too? > Can you provide verbose dmesg's for the > case with pci_link disabled and the case where it is not disabled? Here comes dmesg.acpi (ACPI is fully enabled): Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.1-RC #13: Sun Apr 30 15:39:40 KRAST 2006 root@grosbein.pp.ru:/mnt/usr/local/obj6/usr/src/sys/DADV WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant WARNING: MPSAFE network stack disabled, expect reduced performance. MEMGUARD DEBUGGING ALLOCATOR INITIALIZED: MEMGUARD map base: 0xc36c9000 MEMGUARD map limit: 0xc495b000 MEMGUARD map size: 19472384 (Bytes) Preloaded elf kernel "/boot/kernel/kernel" at 0xc0925000. Preloaded elf module "/boot/modules/acpi.ko" at 0xc092516c. Calibrating clock(s) ... i8254 clock: 1193165 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 902050480 Hz CPU: Intel Celeron (902.05-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 603914240 (575 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c25000 - 0x0000000023597fff, 580333568 bytes (141683 pages) avail memory = 581664768 (554 MB) bios32: Found BIOS32 Service Directory header at 0xc00faef0 bios32: Entry = 0xfb370 (c00fb370) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb3a0 pnpbios: Found PnP BIOS data at 0xc00fbfc0 pnpbios: Entry = f0000:bfe8 Rev = 1.0 Other BIOS signatures found: nfslock: pseudo-device mem: <memory> Pentium Pro MTRR support enabled io: <I/O> null: <null device, zero device> random: <entropy source, Software, Yarrow> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <AWARD AWRDACPI> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086) pcibios: BIOS version 2.10 Found $PIR table, 8 entries at 0xc00fdef0 PCI-Only Interrupts: 9 10 11 Location Bus Device Pin Link IRQs slot 1 0 15 A 0x60 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 B 0x61 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 D 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 0 16 A 0x61 3 4 5 7 9 10 11 12 14 15 slot 2 0 16 B 0x62 3 4 5 7 9 10 11 12 14 15 slot 2 0 16 C 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 0 16 D 0x60 3 4 5 7 9 10 11 12 14 15 slot 3 0 18 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 3 0 18 B 0x63 3 4 5 7 9 10 11 12 14 15 slot 3 0 18 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 3 0 18 D 0x61 3 4 5 7 9 10 11 12 14 15 slot 4 0 19 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 4 0 19 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 4 0 19 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 4 0 19 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 5 0 20 A 0x60 3 4 5 7 9 10 11 12 14 15 slot 5 0 20 B 0x61 3 4 5 7 9 10 11 12 14 15 slot 5 0 20 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 5 0 20 D 0x63 3 4 5 7 9 10 11 12 14 15 slot 6 0 14 A 0x61 3 4 5 7 9 10 11 12 14 15 slot 6 0 14 B 0x62 3 4 5 7 9 10 11 12 14 15 slot 6 0 14 C 0x63 3 4 5 7 9 10 11 12 14 15 slot 6 0 14 D 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 7 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 7 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 7 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 7 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi0: Power Button (fixed) pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 10 11 12 14 15 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 10 11 12 14 15 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 12 14 15 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 10 11 12 14 15 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 10 11 12 14 15 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 12 14 15 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 10 11 12 14 15 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 10 11 12 14 15 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 12 14 15 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 10 11 12 14 15 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 10 11 12 14 15 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 10 11 12 14 15 ACPI timer: 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 -> 0 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x4010 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x4041,0x5000-0x500f on acpi0 ACPI: Found matching pin for 0.16.INTA at func 0: 9 ACPI: Found matching pin for 0.18.INTA at func 0: 10 ACPI: Found matching pin for 0.19.INTA at func 0: 9 ACPI: Found matching pin for 0.19.INTB at func 1: 11 ACPI: Found matching pin for 0.19.INTC at func 2: 9 ACPI: Found matching pin for 0.7.INTD at func 2: 9 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x7190, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 3, range 32, base e8000000, size 26, enabled found-> vendor=0x8086, dev=0x7191, revid=0x03 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x7110, revid=0x02 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x7111, revid=0x01 bus=0, slot=7, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x8086, dev=0x7112, revid=0x01 bus=0, slot=7, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=9 map[20]: type 4, range 32, base 0000a000, size 5, enabled pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.ISA_.LNKD:0) pcib0: slot 7 INTD routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD found-> vendor=0x8086, dev=0x7113, revid=0x02 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[90]: type 4, range 32, base 00005000, size 4, enabled found-> vendor=0x8086, dev=0x1229, revid=0x02 bus=0, slot=16, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=9 map[10]: type 3, range 32, base f0104000, size 12, enabled map[14]: type 4, range 32, base 0000a400, size 5, enabled map[18]: type 1, range 32, base f0000000, size 20, enabled pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ISA_.LNKB:0) pcib0: slot 16 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB found-> vendor=0x105a, dev=0x4d68, revid=0x02 bus=0, slot=18, func=0 class=01-80-85, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0430, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns) intpin=a, irq=10 powerspec 1 supports D0 D1 D3 current D0 map[10]: type 4, range 32, base 0000a800, size 3, enabled map[14]: type 4, range 32, base 0000ac00, size 2, enabled map[18]: type 4, range 32, base 0000b000, size 3, enabled map[1c]: type 4, range 32, base 0000b400, size 2, enabled map[20]: type 4, range 32, base 0000b800, size 4, enabled map[24]: type 1, range 32, base f0100000, size 14, enabled pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.ISA_.LNKC:0) pcib0: slot 18 INTA routed to irq 10 via \\_SB_.PCI0.ISA_.LNKC found-> vendor=0x1106, dev=0x3038, revid=0x61 bus=0, slot=19, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 2 supports D0 D1 D2 D3 current D0 map[20]: type 4, range 32, base 0000bc00, size 5, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0) pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD found-> vendor=0x1106, dev=0x3038, revid=0x61 bus=0, slot=19, func=1 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[20]: type 4, range 32, base 0000c000, size 5, enabled pcib0: matched entry for 0.19.INTB (src \\_SB_.PCI0.ISA_.LNKA:0) pcib0: slot 19 INTB routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA found-> vendor=0x1106, dev=0x3104, revid=0x63 bus=0, slot=19, func=2 class=0c-03-20, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=9 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base f0105000, size 8, enabled pcib0: matched entry for 0.19.INTC (src \\_SB_.PCI0.ISA_.LNKB:0) pcib0: slot 19 INTC routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB found-> vendor=0x1106, dev=0x3044, revid=0x46 bus=0, slot=19, func=3 class=0c-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x20 (8000 ns) intpin=a, irq=9 powerspec 2 supports D0 D2 D3 current D0 map[10]: type 1, range 32, base f0106000, size 11, enabled map[14]: type 4, range 32, base 0000c400, size 7, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0) pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0 agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000 agp0: allocating GATT for aperture of size 64M pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x9000-0x9fff pcib1: memory decode 0xec000000-0xedffffff pcib1: prefetched decode 0xd8000000-0xe7ffffff pci1: <PCI bus> on pcib1 pci1: physical bus=1 found-> vendor=0x1002, dev=0x5961, revid=0x01 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 3, range 32, base d8000000, size 27, enabled pcib1: (null) requested memory range 0xd8000000-0xdfffffff: good map[14]: type 4, range 32, base 00009000, size 8, enabled pcib1: (null) requested I/O range 0x9000-0x90ff: in range map[18]: type 1, range 32, base ed000000, size 16, enabled pcib1: (null) requested memory range 0xed000000-0xed00ffff: good pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.ISA_.LNKA:0) pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA pcib1: slot 0 INTA is routed to irq 11 found-> vendor=0x1002, dev=0x5941, revid=0x01 bus=1, slot=0, func=1 class=03-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 3, range 32, base e0000000, size 27, enabled pcib1: (null) requested memory range 0xe0000000-0xe7ffffff: good map[14]: type 1, range 32, base ed010000, size 16, enabled pcib1: (null) requested memory range 0xed010000-0xed01ffff: good drm0: <ATI Radeon RV280 9200 SE> port 0x9000-0x90ff mem 0xd8000000-0xdfffffff,0xed000000-0xed00ffff irq 11 at device 0.0 on pci1 info: [drm] AGP at 0xe8000000 64MB info: [drm] Initialized radeon 1.19.0 20050911 pci1: <display> at device 0.1 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 7.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000 ata0: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=00 ostat1=00 ata0: stat0=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=00 stat1=00 devices=0x0 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=00 ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata1: stat1=0x00 err=0x04 lsb=0x00 msb=0x02 ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata1: [MPSAFE] uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq 9 at device 7.2 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xa000 uhci0: [GIANT-LOCKED] usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <bridge> at device 7.3 (no driver attached) fxp0: <Intel 82557 Pro/100 Ethernet> port 0xa400-0xa41f mem 0xf0104000-0xf0104fff,0xf0000000-0xf00fffff irq 9 at device 16.0 on pci0 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf0104000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 8086 0001 0002 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:a0:c9:89:95:1f fxp0: [GIANT-LOCKED] atapci1: <Promise PDC20268 UDMA100 controller> port 0xa800-0xa807,0xac00-0xac03,0xb000-0xb007,0xb400-0xb403,0xb800-0xb80f mem 0xf0100000-0xf0103fff irq 10 at device 18.0 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xb800 atapci1: [MPSAFE] ata2: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0xa800 atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xac00 ata2: reset tp1 mask=03 ostat0=50 ostat1=00 ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: <ATA channel 1> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xb000 atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb400 ata3: reset tp1 mask=03 ostat0=50 ostat1=00 ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata3: [MPSAFE] uhci1: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 9 at device 19.0 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbc00 uhci1: [GIANT-LOCKED] usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 11 at device 19.1 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xc000 uhci2: [GIANT-LOCKED] usb2: <VIA 83C572 USB controller> on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered ehci0: <VIA VT6202 USB 2.0 controller> mem 0xf0105000-0xf01050ff irq 9 at device 19.2 on pci0 ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xf0105000 ehci0: [GIANT-LOCKED] ehci0: Dropped interrupts workaround enabled usb3: EHCI version 1.0 usb3: companion controllers, 2 ports each: usb1 usb2 usb3: <VIA VT6202 USB 2.0 controller> on ehci0 usb3: USB revision 2.0 uhub3: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub3: 4 ports with 4 removable, self powered fwohci0: <VIA Fire II (VT6306)> port 0xc400-0xc47f mem 0xf0106000-0xf01067ff irq 9 at device 19.3 on pci0 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xf0106000 fwohci0: [GIANT-LOCKED] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:11:06:66:00:00:0d:c9 fwohci0: Phy 1394a available S400, 3 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:11:06:00:0d:c9 fwe0: bpf attached fwe0: Ethernet address: 02:11:06:00:0d:c9 fwohci0: Initiate bus reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) acpi_tz0: <Thermal Zone> on acpi0 fdc0: <floppy drive controller> port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: irq maps: 0x201 0x211 0x201 0x201 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A sio1: irq maps: 0x201 0x209 0x201 0x201 sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold ppbus0: <Parallel port bus> on ppc0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0047 psm0: found NetMouse/NetScroll Optical psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model NetMouse/NetScroll Optical, device ID 0-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sc: sc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it vga: vga0 already exists; skipping it pnp_identify: Trying Read_Port at 203 YMH0021: start dependent (0) YMH0021: adding io range 0x220-0x22f, size=0x10, align=0x10 YMH0021: adding io range 0x530-0x537, size=0x8, align=0x8 YMH0021: adding io range 0x388-0x38f, size=0x8, align=0x8 YMH0021: adding io range 0x330-0x331, size=0x2, align=0x2 YMH0021: adding io range 0x370-0x371, size=0x2, align=0x2 YMH0021: adding irq mask 0x20 YMH0021: adding dma mask 0x1 YMH0021: adding dma mask 0x2 YMH0021: start dependent (1) YMH0021: adding io range 0x240-0x24f, size=0x10, align=0x10 YMH0021: adding io range 0xe80-0xe87, size=0x8, align=0x8 YMH0021: adding io range 0x388-0x38f, size=0x8, align=0x8 YMH0021: adding io range 0x300-0x301, size=0x2, align=0x2 YMH0021: adding io range 0x100-0xfff, size=0x2, align=0x2 YMH0021: adding irq mask 0xea0 YMH0021: adding dma mask 0xb YMH0021: adding dma mask 0xb YMH0021: start dependent (2) YMH0021: adding io range 0x220-0x28f, size=0x10, align=0x10 YMH0021: adding io range 0x530-0xf4f, size=0x8, align=0x8 YMH0021: adding io range 0x388-0x3ff, size=0x8, align=0x8 YMH0021: adding io range 0x300-0x335, size=0x2, align=0x2 YMH0021: adding io range 0x100-0xfff, size=0x2, align=0x2 YMH0021: adding irq mask 0xea8 YMH0021: adding dma mask 0xb YMH0021: adding dma mask 0xb YMH0021: end dependent YMH0022: start dependent (0) YMH0022: adding io range 0x201-0x201, size=0x1, align=0x1 YMH0022: start dependent (2) YMH0022: adding io range 0x201-0x211, size=0x1, align=0x10 YMH0022: end dependent PNP Identify complete isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd27ff on isa0 fb: new array size 4 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vt0: not probed (disabled) isa_probe_children: probing PnP devices pcm0: <Yamaha OPL-SAx> at port 0x220-0x22f,0x530-0x537,0x388-0x38f,0x330-0x331,0x370-0x371 irq 5 drq 0,1 on isa0 Yamaha: ver 0x21 DMA config 0x83 pcm0: [GIANT-LOCKED] pcm0: sndbuf_setmap ff4000, 1000; 0xdbc11000 -> ff4000 pcm0: sndbuf_setmap ff3000, 1000; 0xdbc12000 -> ff3000 unknown: <OPL3-SA3 Sound Board> failed to probe at port 0x201 on isa0 uscanner0: Hewlett-Packard HP ScanJet 2200C, rev 1.10/1.00, addr 2 ugen0: American Power Conversion Back-UPS 500 FW: 6.5.I USB FW: c1, rev 1.10/1.00, addr 3 Device configuration finished. linprocfs registered procfs registered Timecounter "TSC" frequency 902050480 Hz quality 800 Timecounters tick every 1.000 msec Linux ELF exec handler installed IPsec: Initialized Security Association Processing. DUMMYNET with IPv6 initialized (040826) ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding enabled, default to deny, logging disabled lo0: bpf attached ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire acd0: setting PIO4 on PIIX4 chip acd0: setting UDMA33 on PIIX4 chip acd0: <NEC DVD RW ND-3500AG/2.18> DVDR drive at ata1 as master acd0: read 8268KB/s (8268KB/s) write 8268KB/s (8268KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, DVDR, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-R 120mm data disc ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire ad4: setting PIO4 on PDC20268 chip ad4: setting UDMA100 on PDC20268 chip ad4: 76319MB <WDC WD800JB-00FMA0 13.03G13> at ata2-master UDMA100 ad4: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire ad6: setting PIO4 on PDC20268 chip ad6: setting UDMA100 on PDC20268 chip ad6: 39266MB <IC35L040AVER07 0 ER4OA45A> at ata3-master UDMA100 ad6: 80418240 sectors [79780C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 GEOM: new disk ad6 (probe0:sbp0:0:0:0): error 22 (probe0:sbp0:0:0:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error (probe3:sbp0:0:3:0): error 22 (probe3:sbp0:0:3:0): Unretryable Error (probe4:sbp0:0:4:0): error 22 (probe4:sbp0:0:4:0): Unretryable Error (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error Trying to mount root from ufs:/dev/ad6s2a start_init: trying /sbin/init gif0: bpf attached tun0: bpf attached ata2: reiniting channel .. ata2: reset tp1 mask=03 ostat0=50 ostat1=00 ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly ad4: setting PIO4 on PDC20268 chip ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly ad4: setting UDMA100 on PDC20268 chip ad4: WARNING - SETFEATURES ENABLE RCACHE taskqueue timeout - completing request directly ad4: WARNING - SETFEATURES ENABLE WCACHE taskqueue timeout - completing request directly ad4: WARNING - SET_MULTI taskqueue timeout - completing request directly ata2: reinit done .. ad4: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=100861733 ata3: reiniting channel .. ata3: reset tp1 mask=03 ostat0=50 ostat1=00 ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ad6: setting PIO4 on PDC20268 chip ad6: setting UDMA100 on PDC20268 chip ata3: reinit done .. ad6: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=62118768 fxp0: promiscuous mode enabled link_elf: symbol cd9660_wchar2char undefined link_elf: symbol lminor undefined psm: ENABLE_DEV return code:00fa psm: SEND_AUX_DEV_STATUS return code:00fa psm: status 20 02 64 psm: SET_SAMPLING_RATE (100) 00fa psm: SET_RESOLUTION (3) 00fa psm: SET_SCALING11 return code:00fa psm: SEND_AUX_DEV_STATUS return code:00fa psm: status 20 03 64 fxp0: promiscuous mode disabled Now there is unified diff with dmesg.pcilink (pci_link is disabled): --- dmesg.acpi Sun Apr 30 16:42:09 2006 +++ dmesg.pcilink Sun Apr 30 16:42:09 2006 @@ -11,10 +11,10 @@ MEMGUARD map size: 19472384 (Bytes) Preloaded elf kernel "/boot/kernel/kernel" at 0xc0925000. Preloaded elf module "/boot/modules/acpi.ko" at 0xc092516c. -Calibrating clock(s) ... i8254 clock: 1193165 Hz +Calibrating clock(s) ... i8254 clock: 1193166 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 -Calibrating TSC clock ... TSC clock: 902050480 Hz +Calibrating TSC clock ... TSC clock: 902050201 Hz CPU: Intel Celeron (902.05-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> @@ -83,42 +83,6 @@ acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi0: Power Button (fixed) -pci_link0: Links after initial probe: -Index IRQ Rtd Ref IRQs - 0 11 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link0: Links after initial validation: -Index IRQ Rtd Ref IRQs - 0 11 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link0: Links after disable: -Index IRQ Rtd Ref IRQs - 0 255 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link1: Links after initial probe: -Index IRQ Rtd Ref IRQs - 0 9 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link1: Links after initial validation: -Index IRQ Rtd Ref IRQs - 0 9 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link1: Links after disable: -Index IRQ Rtd Ref IRQs - 0 255 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link2: Links after initial probe: -Index IRQ Rtd Ref IRQs - 0 10 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link2: Links after initial validation: -Index IRQ Rtd Ref IRQs - 0 10 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link2: Links after disable: -Index IRQ Rtd Ref IRQs - 0 255 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link3: Links after initial probe: -Index IRQ Rtd Ref IRQs - 0 9 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link3: Links after initial validation: -Index IRQ Rtd Ref IRQs - 0 9 N 0 3 4 5 6 7 10 11 12 14 15 -pci_link3: Links after disable: -Index IRQ Rtd Ref IRQs - 0 255 N 0 3 4 5 6 7 10 11 12 14 15 ACPI timer: 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 0/3 -> 0 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 @@ -127,12 +91,30 @@ acpi_throttle0: P_CNT from P_BLK 0x4010 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x4041,0x5000-0x500f on acpi0 -ACPI: Found matching pin for 0.16.INTA at func 0: 9 -ACPI: Found matching pin for 0.18.INTA at func 0: 10 -ACPI: Found matching pin for 0.19.INTA at func 0: 9 -ACPI: Found matching pin for 0.19.INTB at func 1: 11 -ACPI: Found matching pin for 0.19.INTC at func 2: 9 -ACPI: Found matching pin for 0.7.INTD at func 2: 9 +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKA +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKB +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKC +pcib0: failed to force attach of \\_SB_.PCI0.ISA_.LNKD pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x7190, revid=0x03 @@ -165,7 +147,6 @@ intpin=d, irq=9 map[20]: type 4, range 32, base 0000a000, size 5, enabled pcib0: matched entry for 0.7.INTD (src \\_SB_.PCI0.ISA_.LNKD:0) -pcib0: slot 7 INTD routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD found-> vendor=0x8086, dev=0x7113, revid=0x02 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 @@ -182,7 +163,6 @@ map[14]: type 4, range 32, base 0000a400, size 5, enabled map[18]: type 1, range 32, base f0000000, size 20, enabled pcib0: matched entry for 0.16.INTA (src \\_SB_.PCI0.ISA_.LNKB:0) -pcib0: slot 16 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB found-> vendor=0x105a, dev=0x4d68, revid=0x02 bus=0, slot=18, func=0 class=01-80-85, hdrtype=0x00, mfdev=0 @@ -197,7 +177,6 @@ map[20]: type 4, range 32, base 0000b800, size 4, enabled map[24]: type 1, range 32, base f0100000, size 14, enabled pcib0: matched entry for 0.18.INTA (src \\_SB_.PCI0.ISA_.LNKC:0) -pcib0: slot 18 INTA routed to irq 10 via \\_SB_.PCI0.ISA_.LNKC found-> vendor=0x1106, dev=0x3038, revid=0x61 bus=0, slot=19, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 @@ -207,7 +186,6 @@ powerspec 2 supports D0 D1 D2 D3 current D0 map[20]: type 4, range 32, base 0000bc00, size 5, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0) -pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD found-> vendor=0x1106, dev=0x3038, revid=0x61 bus=0, slot=19, func=1 class=0c-03-00, hdrtype=0x00, mfdev=1 @@ -217,7 +195,6 @@ powerspec 2 supports D0 D1 D2 D3 current D0 map[20]: type 4, range 32, base 0000c000, size 5, enabled pcib0: matched entry for 0.19.INTB (src \\_SB_.PCI0.ISA_.LNKA:0) -pcib0: slot 19 INTB routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA found-> vendor=0x1106, dev=0x3104, revid=0x63 bus=0, slot=19, func=2 class=0c-03-20, hdrtype=0x00, mfdev=1 @@ -227,7 +204,6 @@ powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base f0105000, size 8, enabled pcib0: matched entry for 0.19.INTC (src \\_SB_.PCI0.ISA_.LNKB:0) -pcib0: slot 19 INTC routed to irq 9 via \\_SB_.PCI0.ISA_.LNKB found-> vendor=0x1106, dev=0x3044, revid=0x46 bus=0, slot=19, func=3 class=0c-00-10, hdrtype=0x00, mfdev=0 @@ -238,7 +214,6 @@ map[10]: type 1, range 32, base f0106000, size 11, enabled map[14]: type 4, range 32, base 0000c400, size 7, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.PCI0.ISA_.LNKD:0) -pcib0: slot 19 INTA routed to irq 9 via \\_SB_.PCI0.ISA_.LNKD agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0 agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe8000000 agp0: allocating GATT for aperture of size 64M @@ -264,8 +239,6 @@ map[18]: type 1, range 32, base ed000000, size 16, enabled pcib1: (null) requested memory range 0xed000000-0xed00ffff: good pcib0: matched entry for 0.1.INTA (src \\_SB_.PCI0.ISA_.LNKA:0) -pcib0: slot 1 INTA routed to irq 11 via \\_SB_.PCI0.ISA_.LNKA -pcib1: slot 0 INTA is routed to irq 11 found-> vendor=0x1002, dev=0x5941, revid=0x01 bus=1, slot=0, func=1 class=03-80-00, hdrtype=0x00, mfdev=0 @@ -494,7 +467,7 @@ Device configuration finished. linprocfs registered procfs registered -Timecounter "TSC" frequency 902050480 Hz quality 800 +Timecounter "TSC" frequency 902050201 Hz quality 800 Timecounters tick every 1.000 msec Linux ELF exec handler installed IPsec: Initialized Security Association Processing. @@ -523,47 +496,24 @@ ad6: 80418240 sectors [79780C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 GEOM: new disk ad6 -(probe0:sbp0:0:0:0): error 22 -(probe0:sbp0:0:0:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error -(probe3:sbp0:0:3:0): error 22 -(probe3:sbp0:0:3:0): Unretryable Error -(probe4:sbp0:0:4:0): error 22 -(probe4:sbp0:0:4:0): Unretryable Error (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error +(probe0:sbp0:0:0:0): error 22 +(probe0:sbp0:0:0:0): Unretryable Error +(probe3:sbp0:0:3:0): error 22 +(probe3:sbp0:0:3:0): Unretryable Error +(probe4:sbp0:0:4:0): error 22 +(probe4:sbp0:0:4:0): Unretryable Error Trying to mount root from ufs:/dev/ad6s2a start_init: trying /sbin/init gif0: bpf attached tun0: bpf attached -ata2: reiniting channel .. -ata2: reset tp1 mask=03 ostat0=50 ostat1=00 -ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 -ata2: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 -ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> -ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly -ad4: setting PIO4 on PDC20268 chip -ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout - completing request directly -ad4: setting UDMA100 on PDC20268 chip -ad4: WARNING - SETFEATURES ENABLE RCACHE taskqueue timeout - completing request directly -ad4: WARNING - SETFEATURES ENABLE WCACHE taskqueue timeout - completing request directly -ad4: WARNING - SET_MULTI taskqueue timeout - completing request directly -ata2: reinit done .. -ad4: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=100861733 -ata3: reiniting channel .. -ata3: reset tp1 mask=03 ostat0=50 ostat1=00 -ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 -ata3: stat1=0x00 err=0x01 lsb=0x00 msb=0x00 -ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> -ad6: setting PIO4 on PDC20268 chip -ad6: setting UDMA100 on PDC20268 chip -ata3: reinit done .. -ad6: TIMEOUT - WRITE_DMA retrying (1 retry left) LBA=62118768 fxp0: promiscuous mode enabled link_elf: symbol cd9660_wchar2char undefined link_elf: symbol lminor undefined Eugene Grosbein
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200604300850.k3U8oIfa015644>