Date: Fri, 16 Jul 2004 19:16:00 +0100 From: Feargal Reilly <feargal@chrysalink.net> To: freebsd-hardware@freebsd.org Subject: SATA RAID with Intel 300ESB chipset Message-ID: <20040716191600.282c3dc9@beaker.chrysalink.net>
next in thread | raw e-mail | index | archive | help
--Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy
Content-Type: multipart/mixed;
boundary="Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z"
--Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z
Content-Type: text/plain; charset=US-ASCII
Content-Disposition: inline
Content-Transfer-Encoding: 7bit
Hi,
I've been trying to install either FreeBSD 4.10 or 5.2.1 from
CD onto a machine with the Intel SE7210TP motherboard. This has
two 80G disks connected to an onboard RAID controller which,
according to the documentation, is the Intel 300ESB I/O
Controller Hub.
If, in the BIOS, I map PATA and SATA to Legacy ATA, both 4.10 and
5.2.1 CDs boot and install fine. Obviously though that's
downgrading my shiny new SATA disks.
If I map PATA to Legacy ATA and enable SATA, then 5.2.1
boots and installs fine, but 4.10 hangs after kernel
configuration, tail of log is:
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63
sectors 1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads,
1..63=63 sectors 0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: sl0 attached
Full output is attached as 4.10-PATA+SATA.log
Finally, if I enable SATA RAID and map PATA to Legacy ATA, both
4.10 and 5.2.1 boot from the CD, but neither recognises the RAID
array; when I try to install, sysinstall tells me "No disks
found!" and suggests my disk controller is not being properly
probed. This happens whether I set up RAID-0, RAID-1, or no RAID
array at all.
I've tried pre-loading various modules in the hope that they
would recognise the array, but to no avail.
I'd seen Doug Ambrisko's patch from March which led me to believe
that this controller was supported, but a quick look at the
sources on other machines suggests that it wasn't committed.
What's the best way forward for me? Ideal situation would be to
get the RAID controller working on 4.10, but I'm not seeing any
success with SATA at all so I'm guessing my best chance would be
on 5.2.1. I would rather get the hardware working than go down
the vinum route. This server doesn't have to be in action for a
week or two, so I can forget about vinum until then.
Here's the full output from the 5.2.1. SATA RAID attempt with a
single RAID1 array, (the 4.10 attempt is attached):
Serial Redir 2.0.5 [VT-100+]
BIOS LAN Console 4.0
Copyright (C) 1997-2002 Intel Corporation
AMIBIOS(C)2003 American Megatrends, Inc.
BIOS Date: 12/25/03 13:42:43 Ver: 08.00.10
SE7210TP10 Production BIOS Version 01.00, Build 0023
CPU : Intel(R) Pentium(R) 4 CPU 3.20GHz
Speed : 3.20 GHz
Press <F2> to run Setup
Press <F12> for Network Boot
Press <ESC> for BBS POPUP
DDR Frequency 400 Mhz, Dual-Channel
Checking NVRAM..
Initializing USB Controllers .. Done.
Testing system memory, memory size=1024MB
1024MB Extended Memory Passed
(C)AmericanMegatrends,Inc.
64-0100-000023-00101111-122503-CANTWOOD-STP1A023-Y2KC
System Event Log Full
Auto-Detecting Pri Master..ATAPI CDROM
Auto-Detecting 3rd Master..IDE Hard Disk
Auto-Detecting 4th Master..IDE Hard Disk
Pri Master: CREATIVEDVD1240E 3X14
Ultra DMA Mode-2
3rd Master: ST380013AS 3.18
Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
4th Master: ST380013AS 3.18
Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
Auto-detecting USB Mass Storage Devices ..
00 USB mass storage devices found and configured.
Adaptec Embedded SATA HostRAID BIOS V1.0-0 1024
(c) 1998-2003 Adaptec, Inc. All Rights Reserved.
... Press <Ctrl><A> for Adaptec RAID Configuration Utility! ...
Controller #00: Adaptec HostRAID at PCI Bus:00, Dev:1F, Func:02
Waiting for Controller to Start....Controller started
Port#00 ST380013AS 3.18 74.53 GB Healthy
Port#01 ST380013AS 3.18 74.53 GB Healthy
Array #0 - RAID-1 RAID1 74.53 GB Optimal
1 Logical Device(s) Found.
+===============================================================
============+| System Configuration, AMIBIOS Version
08.00.10
|+==============================================================
=============+| Main Processor(s): Intel(R) Pentium(R) 4 CPU
3.20GHz
|+==============================================================
=============+| Math Processor : Built-In Base Memory
Size : 640KB || Floppy Drive A: : 1.44 MB 3@"
Extd Memory Size : 1023MB || Serial Port(s) : 3F8,2F8
Display Type : VGA/EGA || BIOS Build Date
: 12/25/03 PS/2 Mouse : None || ACPI
1.0 Support : Enabled
|+==============================================================
=============+| ATA(PI) Device(s) Type Size LBA Block
SMART 32Bit DMA PIO ||
Mode Mode Info Mode Mode Mode|| Primary Master : ATAPI
CDROM UDMA2 4
|+==============================================================
=============+| PCI Devices:
|| PCI Onboard PCI Bridge
PCI Onboard PCI Bridge || PCI Onboard USB
Controller,IRQ9 PCI Onboard System Device || PCI
Onboard System Device PCI Onboard USB Controller,IRQ5
|| PCI Onboard USB Controller,IRQ7 PCI Onboard PCI
Bridge || PCI Onboard SerialBus Cntlr,IRQ5 PCI
Onboard RAID,IRQ9 || PCI Onboard IDE
PCI Bridge Ethernet,IRQ9 || PCI Bridge
VGA,IRQ11 PCI Bridge Ethernet,IRQ5
|+==============================================================
=============+
Press <ESC> to boot....1
CD Loader 1.01
Building the boot loader arguments
Looking up /BOOT/LOADER... Found
Relocating the loader and the BTX
Starting the BTX loader
BTX loader 1.00 BTX version is 1.01
Console: internal video/keyboard
BIOS CD is cd0
BIOS drive A: is disk0
BIOS drive C: is disk1
BIOS 631kB/1047488kB available memory
FreeBSD/i386 bootstrap loader, Revision 1.1
(root@wv1u.btc.adaptec.com, Mon Feb 23 18:35:51 GMT 2004)
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x45d64c data=0x7948c+0x47a10
syms=[0x4+0x57ee0+0x4+0x6 a2f2]
/
+-----------------------------------------+
| |
| | ,
, | | /(
)` | Welcome to FreeBSD! | \
\___ / | | |
/- _ `-/ ' | |
(/\/ \ \ /\ | 1. Boot FreeBSD [default] |
/ / | ` \ | 2. Boot FreeBSD with ACPI disabled |
O O ) / | | 3. Boot FreeBSD in Safe Mode
| `-^--'`< ' | 4. Boot FreeBSD in single user
mode | (_.) _ ) / | 5. Boot FreeBSD with
verbose logging | `.___/` / | 6. Escape to
loader prompt | `-----' / | 7. Reboot
| <----. __ / __ \ |
| <----|====O)))==) \) /==== |
| <----' `--' `.__,' \ |
| | | |
| \ /
/\ | Select option, [Enter] for default |
______( (_ / \______/ | or [Space] to pause timer 9
| ,' ,-----' |
+-----------------------------------------+
`--{__________)
Type '?' for a list of commands, 'help' for more detailed help.
OK boot -Dh -v
/boot/kernel/acpi.ko text=0x3f088 data=0x1744+0x114c
syms=[0x4+0x6b20+0x4+0x866e]
-SMAP type=01 base=0000000000000000 len=000000000009dc00
SMAP type=02 base=000000000009dc00 len=0000000000002400
SMAP type=02 base=00000000000e0000 len=0000000000020000
SMAP type=01 base=0000000000100000 len=000000003fef0000
SMAP type=03 base=000000003fff0000 len=000000000000f000
SMAP type=04 base=000000003ffff000 len=0000000000001000
SMAP type=02 base=00000000ffb00000 len=0000000000500000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
1993, 1994 The Regents of the University of California.
All rights reserved. FreeBSD 5.2.1-RELEASE #0: Mon Feb 23
20:45:55 GMT 2004
root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded
elf kernel "/boot/kernel/kernel" at 0xc0e6d000. Preloaded
mfs_root "/boot/mfsroot" at 0xc0e6d204. Preloaded elf module
"/boot/kernel/acpi.ko" at 0xc0e6d248. Table 'FACP' at 0x3fff0200
Table 'APIC' at 0x3fff0390
MADT: Found table at 0x3fff0390
MP Configuration Table version 1.4 found at 0xc00fbab0
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
SMP: Added CPU 1 (AP)
ACPI APIC Table: <A M I OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193114 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 3192008572 Hz
CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.01-MHz 686-class
CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,
MTRR,PGE,MCA,CMO
V,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs real memory = 1073676288 (1023
MB) Physical memory chunk(s):
0x0000000000001000 - 0x000000000009cfff, 638976 bytes (156 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768
pages) 0x0000000001029000 - 0x000000003edc9fff, 1037701120 bytes
(253345 pages) avail memory = 1029316608 (981 MB)
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
pnpbios: Found PnP BIOS data at 0xc00f4f30
pnpbios: Entry = f0000:5c34 Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
MADT: Found IO APIC ID 3, Vector 24 at 0xfec10000
ioapic1: intpin 0 -> irq 24 (level, activelo)
ioapic1: intpin 1 -> irq 25 (level, activelo)
ioapic1: intpin 2 -> irq 26 (level, activelo)
ioapic1: intpin 3 -> irq 27 (level, activelo)
ioapic1: intpin 4 -> irq 28 (level, activelo)
ioapic1: intpin 5 -> irq 29 (level, activelo)
ioapic1: intpin 6 -> irq 30 (level, activelo)
ioapic1: intpin 7 -> irq 31 (level, activelo)
ioapic1: intpin 8 -> irq 32 (level, activelo)
ioapic1: intpin 9 -> irq 33 (level, activelo)
ioapic1: intpin 10 -> irq 34 (level, activelo)
ioapic1: intpin 11 -> irq 35 (level, activelo)
ioapic1: intpin 12 -> irq 36 (level, activelo)
ioapic1: intpin 13 -> irq 37 (level, activelo)
ioapic1: intpin 14 -> irq 38 (level, activelo)
ioapic1: intpin 15 -> irq 39 (level, activelo)
ioapic1: intpin 16 -> irq 40 (level, activelo)
ioapic1: intpin 17 -> irq 41 (level, activelo)
ioapic1: intpin 18 -> irq 42 (level, activelo)
ioapic1: intpin 19 -> irq 43 (level, activelo)
ioapic1: intpin 20 -> irq 44 (level, activelo)
ioapic1: intpin 21 -> irq 45 (level, activelo)
ioapic1: intpin 22 -> irq 46 (level, activelo)
ioapic1: intpin 23 -> irq 47 (level, activelo)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 10, irq 10
ioapic0: intpin 10 trigger: level
ioapic0: intpin 10 polarity: active-hi
lapic0: Routing NMI -> LINT1
lapic1: Routing NMI -> LINT1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR:
0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000
SVR: 0x000001ff wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <A M I OEMRSDT > on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there
(id=25788086) pcibios: No call entry point
pcibios: No call entry point
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 3, width = 0
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on
acpi0 acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base fe800000, size 22,
enabled found-> vendor=0x8086, dev=0x2578, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) found-> vendor=0x8086, dev=0x257b, revid=0x02
bus=0, slot=3, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns),
maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25ae, revid=0x02
bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0146, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns),
maxlat=0x00 (0 ns) map[20]: type 4, range 32, base
0000e800, size 5, enabled pcib0: matched entry for 0.29.INTA
(source ) pcib0: device is hardwired to IRQ 16
found-> vendor=0x8086, dev=0x25a9, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=a, irq=16
map[20]: type 4, range 32, base 0000ec00, size 5,
enabled pcib0: matched entry for 0.29.INTB (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x25aa, revid=0x02
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=b, irq=19
map[10]: type 1, range 32, base fe7ff800, size 4,
enabled found-> vendor=0x8086, dev=0x25ab, revid=0x02
bus=0, slot=29, func=4
class=08-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0002, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) found-> vendor=0x8086, dev=0x25ac, revid=0x02
bus=0, slot=29, func=5
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0146, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) map[10]: type 1, range 32, base fe7ffc00, size 10,
enabled pcib0: matched entry for 0.29.INTD (source )
pcib0: device is hardwired to IRQ 23
found-> vendor=0x8086, dev=0x25ad, revid=0x02
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=d, irq=23
powerspec 2 supports D0 D3 current D0
found-> vendor=0x8086, dev=0x244e, revid=0x0a
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00
(0 ns) found-> vendor=0x8086, dev=0x25a1, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) map[10]: type 4, range 32, base 00000000, size 3,
enabled map[14]: type 4, range 32, base 00000000, size 2,
enabled map[18]: type 4, range 32, base 00000000, size 3,
enabled map[1c]: type 4, range 32, base 00000000, size 2,
enabled map[20]: type 4, range 32, base 0000fc00, size 4,
enabled found-> vendor=0x8086, dev=0x25a2, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0288, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=a, irq=255
map[10]: type 4, range 32, base 0000e400, size 3,
enabled map[14]: type 4, range 32, base 0000e000, size 2,
enabled map[18]: type 4, range 32, base 0000dc00, size 3,
enabled map[1c]: type 4, range 32, base 0000d800, size 2,
enabled map[20]: type 4, range 32, base 0000d400, size 4,
enabled pcib0: matched entry for 0.31.INTA (source )
pcib0: device is hardwired to IRQ 18
found-> vendor=0x8086, dev=0x25b0, revid=0x02
bus=0, slot=31, func=2
class=01-04-8f, hdrtype=0x00, mfdev=0
cmdreg=0x0445, statreg=0x02a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=a, irq=18
map[20]: type 4, range 32, base 00000400, size 5,
enabled pcib0: matched entry for 0.31.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x25a4, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0
ns) intpin=b, irq=17
pcibios: No call entry point
pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xb000-0xbfff
pcib1: memory decode 0xfc500000-0xfc5fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pcib1: could not get PCI interrupt routing table for
\_SB_.PCI0.P0P2 - AE_NOT_FOUN D
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base fc5e0000, size 17,
enabled map[18]: type 4, range 32, base 0000bc00, size 5,
enabled found-> vendor=0x8086, dev=0x1075, revid=0x00
bus=1, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0238, cachelnsz=8 (dwords)
lattimer=0x00 (0 ns), mingnt=0xff (63750 ns), maxlat=0x00
(0 ns) intpin=a, irq=9
powerspec 2 supports D0 D3 current D0
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19>
port 0xbc00-0xbc1f m em 0xfc5e0000-0xfc5fffff irq 9 at device 1.0
on pci1 pcib1: device em0 requested decoded memory range
0xfc5e0000-0xfc5fffff pcib1: device em0 requested decoded I/O
range 0xbc00-0xbc1f em0: bpf attached
em0: Speed:N/A Duplex:N/A
pcibios: No call entry point
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xfff00000-0xfffff
pcib2: prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
uhci0: <UHCI (generic) USB controller> port 0xe800-0xe81f irq 16
at device 29.0 on pci0
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xec00-0xec1f irq 19
at device 29.1 on pci0
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <base peripheral> at device 29.4 (no driver attached)
pci0: <base peripheral, interrupt controller> at device 29.5 (no
driver attached) pci0: <serial bus, USB> at device 29.7 (no
driver attached) pcibios: No call entry point
pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xc000-0xcfff
pcib3: memory decode 0xfc600000-0xfe6fffff
pcib3: prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3
map[10]: type 1, range 32, base fd000000, size 24,
enabled map[14]: type 4, range 32, base 0000c800, size 8,
enabled map[18]: type 1, range 32, base fe6ff000, size 12,
enabled pcib3: matched entry for 3.0.INTA (source )
pcib3: device is hardwired to IRQ 21
found-> vendor=0x1002, dev=0x4752, revid=0x27
bus=3, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns),
maxlat=0x00 (0 ns) intpin=a, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fe6fe000, size 12,
enabled map[14]: type 4, range 32, base 0000cc00, size 6,
enabled map[18]: type 1, range 32, base fe6a0000, size 17,
enabled pcib3: matched entry for 3.1.INTA (source )
pcib3: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x1229, revid=0x10
bus=3, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0157, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns),
maxlat=0x38 (14000 ns) intpin=a, irq=17
powerspec 2 supports D0 D1 D2 D3 current D0
pci3: <display, VGA> at device 0.0 (no driver attached)
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xcc00-0xcc3f mem
0xfe6a0000-0xfe6bffff, 0xfe6fe000-0xfe6fefff irq 17 at device 1.0
on pci3 pcib3: device fxp0 requested decoded memory range
0xfe6fe000-0xfe6fefff fxp0: using memory space register mapping
fxp0: Ethernet address 00:02:b3:e9:8e:8d
fxp0: PCI IDs: 8086 1229 8086 342f 0010
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <GENERIC ATA controller> port
0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at de vice 31.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=00 stat1=00
devices=0x4<ATAPI_MASTER> ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1-master: stat=0x01 err=0x01 lsb=0x01 msb=0x01
ata1-slave: stat=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: reset tp2 mask=03 stat0=01 stat1=01 devices=0x0
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <mass storage, RAID> at device 31.2 (no driver attached)
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on
acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
psmcpnp0 irq 12 on acpi0
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)>
port 0x3f7,0x3f0-0x3 f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xdc000-0xdffff,0xc8000-0xcbfff,0xc0000-0xc7fff on is a0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 3192008572 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09e16d8
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently
100.0% ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin
GEOM: Configure md0a, start 0 length 4423680 end 4423679
GEOM: Configure md0c, start 0 length 4423680 end 4423679
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
acd0: <CREATIVEDVD1240E/3X14> DVDROM drive at ata0 as master
acd0: read 6875KB/s (6875KB/s), 512KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x02000000 DFR:
0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000
SVR: 0x000001ff ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 3 (IRQ 3) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 10 (IRQ 10) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
Mounting root from ufs:/dev/md0
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console
These are the predefined terminal types available to
sysinstall when running stand-alone. Please choose the
closest match for your particular terminal.
1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).
5 ...................... xterm terminal emulator.
Your choice: (1-5)
<snip>Sysinstall starts, following error occurs:
No disks found! Please verify that your disk controller is being
| properly probed at boot time. See the Hardware Guide on the
Documentation menu for clues on diagnosing this type of problem.
</snip>
If you read this far, thank you...
--
Feargal Reilly, Codeshifter, Chrysalink Systems.
ICQ: 109837009 | YIM: ectoraige
PGP Key ID: 0xA6F82C96 (expires 09-Jun-2005)
Visit http://ie.bsd.net/ - BSDs presence in Ireland
--Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z
Content-Type: text/plain;
name="4.10-PATA+SATA.log"
Content-Disposition: attachment;
filename="4.10-PATA+SATA.log"
Content-Transfer-Encoding: 7bit
Serial Redir 2.0.5 [VT-100+]
BIOS LAN Console 4.0
Copyright (C) 1997-2002 Intel Corporation
AMIBIOS(C)2003 American Megatrends, Inc.
BIOS Date: 12/25/03 13:42:43 Ver: 08.00.10
SE7210TP10 Production BIOS Version 01.00, Build 0023
CPU : Intel(R) Pentium(R) 4 CPU 3.20GHz
Speed : 3.20 GHz
Press <F2> to run Setup
Press <F12> for Network Boot
Press <ESC> for BBS POPUP
DDR Frequency 400 Mhz, Dual-Channel
Checking NVRAM..
Initializing USB Controllers .. Done.
Testing system memory, memory size=1024MB
1024MB Extended Memory Passed
(C)AmericanMegatrends,Inc. 64-0100-000023-00101111-122503-CANTWOOD-STP1A023-Y2KC
System Event Log Full
Auto-Detecting Pri Master..ATAPI CDROM
Auto-Detecting 3rd Master..IDE Hard Disk
Auto-Detecting 4th Master..IDE Hard Disk
Pri Master: CREATIVEDVD1240E 3X14
Ultra DMA Mode-2
3rd Master: ST380013AS 3.18
Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
4th Master: ST380013AS 3.18
Ultra DMA Mode-5, S.M.A.R.T. Capable and Status OK
Auto-detecting USB Mass Storage Devices ..
00 USB mass storage devices found and configured.
+===========================================================================+
| Main Processor(s): Intel(R) Pentium(R) 4 CPU 3.20GHz |
+===========================================================================+
| Math Processor : Built-In Base Memory Size : 640KB |
| Floppy Drive A: : 1.44 MB 3@" Extd Memory Size : 1023MB |
| Serial Port(s) : 3F8,2F8 Display Type : VGA/EGA |
| BIOS Build Date : 12/25/03 PS/2 Mouse : None |
| ACPI 1.0 Support : Enabled |
+===========================================================================+
| ATA(PI) Device(s) Type Size LBA Block SMART 32Bit DMA PIO |
| Mode Mode Info Mode Mode Mode|
| Third Master : Hard Disk 80.0GB LBA 16Sec Good Off UDMA5 4 |
| Fourth Master : Hard Disk 80.0GB LBA 16Sec Good Off UDMA5 4 |
| Primary Master : ATAPI CDROM UDMA2 4 |
+===========================================================================+
| PCI Devices: |
| PCI Onboard PCI Bridge PCI Onboard PCI Bridge |
| PCI Onboard USB Controller,IRQ9 PCI Onboard System Device |
| PCI Onboard System Device PCI Onboard USB Controller,IRQ5 |
| PCI Onboard USB Controller,IRQ7 PCI Onboard PCI Bridge |
| PCI Onboard SerialBus Cntlr,IRQ5 PCI Onboard IDE,IRQ5 |
| PCI Onboard IDE PCI Bridge Ethernet,IRQ5 |
| PCI Bridge VGA,IRQ11 PCI Bridge Ethernet,IRQ5 |
+===========================================================================+
Press <ESC> to boot....1
Uncompressing ... done
BTX loader 1.00 BTX version is 1.01
Console: internal video/keyboard
BIOS drive A: is disk0
BIOS drive B: is disk1
BIOS drive C: is disk2
BIOS drive D: is disk3
BIOS 579kB/1047488kB available memory
FreeBSD/i386 bootstrap loader, Revision 0.8
(root@perseus.cse.buffalo.edu, Tue May 25 21:22:31 GMT 2004)
/kernel text=0x28b691 data=0x3006c+0x32cc8 \
-
Hit [Enter] to boot immediately, or any other key for command prompt.
Type '?' for a list of commands, 'help' for more detailed help.
ok boot -D -h -v
SMAP type=01 base=0000000000000000 len=0000000000090c00
SMAP type=02 base=0000000000090c00 len=000000000000f400
SMAP type=02 base=00000000000e0000 len=0000000000020000
SMAP type=01 base=0000000000100000 len=000000003fef0000
SMAP type=03 base=000000003fff0000 len=000000000000f000
SMAP type=04 base=000000003ffff000 len=0000000000001000
SMAP type=02 base=00000000ffb00000 len=0000000000500000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Tue May 25 22:52:21 GMT 2004
root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/BOOTMFS
Calibrating clock(s) ... TSC clock: 3191799576 Hz, i8254 clock: 1193107 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 3192010216 Hz
CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3192.01-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
MOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1073676288 (1048512K bytes)
Physical memory chunk(s):
0x000001000 - 0x00008ffff, 585728 bytes (143 pages)
0x000850000 - 0x03ffe7fff, 1064927232 bytes (259992 pages)
config> intro
<snip>Kernel Configuration Menu, there were no conflicts so skipped it</snip>
avail memory = 1037336576 (1013024K bytes)
pnpbios: Found PnP BIOS data at 0xc00f4f30
pnpbios: Entry = f0000:5c34 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f7610
Preloaded elf kernel "kernel" at 0xc0829000.
Preloaded mfs_root "/mfsroot" at 0xc0829098.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03ef3d4
Creating DISK md0
Creating DISK md1
md1: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25788086)
pcibios: No call entry point
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x2578, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fe800000, size 22
found-> vendor=0x8086, dev=0x257b, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x25ae, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=2 secondarybus=2
found-> vendor=0x8086, dev=0x25a9, revid=0x02
class=0c-03-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=7
map[20]: type 1, range 32, base 0000e800, size 5
found-> vendor=0x8086, dev=0x25aa, revid=0x02
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=5
map[20]: type 1, range 32, base 0000ec00, size 5
found-> vendor=0x8086, dev=0x25ab, revid=0x02
class=08-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base fe7ff800, size 4
found-> vendor=0x8086, dev=0x25ac, revid=0x02
class=08-00-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x25ad, revid=0x02
class=0c-03-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[10]: type 1, range 32, base fe7ffc00, size 10
found-> vendor=0x8086, dev=0x244e, revid=0x0a
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=3 secondarybus=3
found-> vendor=0x8086, dev=0x25a1, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x25a2, revid=0x02
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=0
map[10]: type 1, range 32, base 00000000, size 3
map[14]: type 1, range 32, base 00000000, size 2
map[18]: type 1, range 32, base 00000000, size 3
map[1c]: type 1, range 32, base 00000000, size 2
map[20]: type 1, range 32, base 0000fc00, size 4
found-> vendor=0x8086, dev=0x25a3, revid=0x02
class=01-01-8f, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000e400, size 3
map[14]: type 1, range 32, base 0000e000, size 2
map[18]: type 1, range 32, base 0000dc00, size 3
map[1c]: type 1, range 32, base 0000d800, size 2
map[20]: type 1, range 32, base 0000d400, size 4
found-> vendor=0x8086, dev=0x25a4, revid=0x02
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=5
map[20]: type 1, range 32, base 00000400, size 5
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=257b)> at device 3.0 on pci0
found-> vendor=0x8086, dev=0x1075, revid=0x00
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base fc5e0000, size 17
map[18]: type 1, range 32, base 0000bc00, size 5
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1075) at 1.0 irq 5
pcib2: <PCI to PCI bridge (vendor=8086 device=25ae)> at device 28.0 on pci0
pci2: <PCI bus> on pcib2
uhci0: <UHCI (generic) USB controller> port 0xe800-0xe81f irq 7 at device 29.0 on0
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xec00-0xec1f irq 5 at device 29.1 on0
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x8086, dev=0x25ab) at 29.4
pci0: <unknown card> (vendor=0x8086, dev=0x25ac) at 29.5
pci0: <USB controller> (vendor=0x8086, dev=0x25ad) at 29.7 irq 9
pcib3: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
found-> vendor=0x1002, dev=0x4752, revid=0x27
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base fd000000, size 24
map[14]: type 1, range 32, base 0000c800, size 8
map[18]: type 1, range 32, base fe6ff000, size 12
found-> vendor=0x8086, dev=0x1229, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base fe6fe000, size 12
map[14]: type 1, range 32, base 0000cc00, size 6
map[18]: type 1, range 32, base fe6a0000, size 17
pci3: <PCI bus> on pcib3
pci3: <ATI Mach64-GR graphics accelerator> (vendor=0x1002, dev=0x4752) at 0.0 irq1
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xcc00-0xcc3f mem 0xfe6a0000-0xfe6bffff3
fxp0: using memory space register mapping
using shared irq5.
fxp0: Ethernet address 00:02:b3:e9:8e:8d
fxp0: PCI IDs: 8086 1229 8086 342f 0010
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
isab0: <PCI to ISA bridge (vendor=8086 device=25a1)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xfc00
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 14 eb
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=00 stat1=00
ata0: devices=04
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xfc08
ata1: mask=03 ostat0=00 ostat2=00
ata1-master: ATAPI 74 74
ata1-slave: ATAPI 74 74
ata1: mask=03 stat0=74 stat1=74
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
atapci1: <Generic PCI ATA controller> port 0xd400-0xd40f,0xd800-0xd803,0xdc00-0xd0
ata-: ata2 exists, using next available unit number
ata2: iobase=0xe400 altiobase=0xe002 bmaddr=0xd400
ata2: mask=03 ostat0=50 ostat2=00
ata2-slave: ATAPI c5 fa
ata2-master: ATAPI 00 00
ata2: mask=03 stat0=50 stat1=00
ata2-master: ATA 01 a5
ata2: devices=01
ata2: at 0xe400 on atapci1
ata3: iobase=0xdc00 altiobase=0xd802 bmaddr=0xd408
ata3: mask=03 ostat0=50 ostat2=00
ata3-slave: ATAPI c5 fa
ata3-master: ATAPI 00 00
ata3: mask=03 stat0=50 stat1=00
ata3-master: ATA 01 a5
ata3: devices=01
ata3: at 0xdc00 on atapci1
pci0: <unknown card> (vendor=0x8086, dev=0x25a4) at 31.3 irq 5
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xdc000-0xdffff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
ata4 failed to probe at port 0x1f0 irq 14 on isa0
ata5 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 06 90 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: irq maps: 0 0 0 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0 0 0 0
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: sl0 attached
--Multipart=_Fri__16_Jul_2004_19_16_00_+0100_0ALERQe1tlRtbN5Z--
--Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy
Content-Type: application/pgp-signature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (FreeBSD)
iD8DBQFA+BthorFlI6b4LJYRAmwkAJ0W74EpOGdBgCZh7wu875Xw4DG8IgCfXgTq
8Aed4o0oFIOky6lq1VIH5XA=
=636f
-----END PGP SIGNATURE-----
--Signature=_Fri__16_Jul_2004_19_16_00_+0100_HTskwW.lMrmAf9fy--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040716191600.282c3dc9>