Date: Fri, 14 Apr 2000 14:35:59 -0700 From: Edwin Culp <eculp@EnContacto.Net> To: "Michael I. Vasilenko" <acid@cn.ua>, "current@FreeBSD.ORG" <current@FreeBSD.ORG> Subject: Re: PCI-CardBus bridge + PCMCIA Lucent WaveLAN IEEE troubles Message-ID: <38F78F3E.9A5FED22@EnContacto.Net> References: <Pine.BSF.4.21.0004141931270.33533-100000@wicket.ci.net.ua> <38F78D5A.FBC13546@EnContacto.Net>
next in thread | previous in thread | raw e-mail | index | archive | help
Edwin Culp wrote:
> Michael,
>
> I just threw one in my laptop a couple of days ago. I didn't even have to recompile the kernel. I just
> added the stock WaveLAN section to my pccard.conf let it load the if_wi.ko and it worked. Although when I
> reboot I have to take the card out and put it back in because there seems to be a delay with the kernel
> module that causes the driver to initially fail that probably wouldn't happen if I had support compiled
> into the kernel, but I really didn't plan to use it that often but it is working so well I think that I
> will.
>
> My pccard.conf is :
> # Generally available IO ports
> io 0x240-0x360
> # Generally available IRQs (Built-in sound-card owners remove 5)
> irq 9 11
> #
> # Cut out my modem and nic entries.
> #
> # Lucent WaveLAN/IEEE
> card "Lucent Technologies" "WaveLAN/IEEE"
> config 0x1 "wi0" ?
> insert logger -t pccard:$device -s WaveLAN/IEEE inserted
> insert /etc/pccard_ether $device
> remove logger -t pccard:$device -s WaveLAN/IEEE removed
> remove /sbin/ifconfig $device delete
>
> The messages are:
> # kldstat
> 1 0xc0c73000 5000 if_wi.ko
>
> pccard1: <PC Card bus -- kludge version> on pcic0
> pccard: card inserted, slot 0
> pccard: card removed, slot 0
> pccard: card inserted, slot 0
> wi0: <WaveLAN/IEEE 802.11> at port 0x240-0x27f irq 9 slot 0 on pccard0
> wi0: Ethernet address: 00:60:1d:03:f4:08
Forgot, sorry. The difference that I see is that you have TI PCI-1225.
pcic-pci0: <TI PCI-1220 PCI-CardBus Bridge> irq 10 at device 3.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pcic-pci1: <TI PCI-1220 PCI-CardBus Bridge> irq 10 at device 3.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pcic0: <VLSI 82C146> at port 0x3e0-0x3e1 on isa0
pcic0: Polling mode
>
>
> Hope this helps.
>
> ed
>
> P.S. I did have to make some configuration changes with wicontrol to communicate with my in-talk/nokia
> access point.
>
> "Michael I. Vasilenko" wrote:
>
> > Recently our firm bought Lucent wireless hardware - PCI Adapter and
> > PCMCIA card. After unsucsessfull trying to get it work on 3.4+PAO,
> > I've upgraded to 5.0-CURRENT.
> >
> > All hardware ssems to be detected, pccardc pccardmem 0xd4000 is ok,
> > but after running pccardd it says:
> >
> > pccardd[166]: Card "Lucent Technologies"("WaveLAN/IEEE") matched "Lucent Technologies" ("WaveLAN/IEEE")
> > pccardd[166]: Using I/O addr 0x100, size 64
> > pccardd[166]: Setting config reg at offs 0x3e0 to 0x41, Reset time = 50 ms
> > pccardd[166]: Assigning I/O window 0, start 0x100, size 0x40 flags 0x5
> > /kernel: wi0: <WaveLAN/IEEE 802.11> at port 0x100-0x13f irq 7 slot 0 on pccard0
> > /kernel: wi0: Ethernet address: 00:60:1d:f6:cc:5d
> >
> > and machine just hangs completly.
> >
> > Any help would be great.
> >
> > kernel config:
> >
> > device card
> > device pcic0 at isa?
> > device wi
> >
> > kernel.conf:
> >
> > config> port pcic0 0x3e0
> > config> irq pcic0 5
> > config> iomem pcic0 0xd4000
> > config> q
> >
> > pieces of dmesg:
> >
> > ...
> > pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> mem 0xea000000-0xea000fff irq 10 at device 16.0 on pci0
> > pcic-pci0: TI12XX PCI Config Reg: [pwr save][pci only]
> > pcic-pci0: Legacy address set to 0x3e0
> > pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> mem 0xea004000-0xea004fff irq 10 at device 16.1 on pci0
> > pcic-pci1: TI12XX PCI Config Reg: [pwr save][pci only]
> > ...
> > pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd4000 irq 5 drq 0 on isa0
> > pcic0: management irq 5
> > pccard0: <PC Card bus -- kludge version> on pcic0
> > pccard1: <PC Card bus -- kludge version> on pcic0
> > ...
> > pccard: card inserted, slot 0
> > pccard: card inserted, slot 1
> >
> > To Unsubscribe: send mail to majordomo@FreeBSD.org
> > with "unsubscribe freebsd-current" in the body of the message
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-current" in the body of the message
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?38F78F3E.9A5FED22>