Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 2 Apr 2008 08:29:27 +0100
From:      "Stuart Fraser" <stuart@stuartfraser.net>
To:        <pyunyh@gmail.com>
Cc:        freebsd-current@freebsd.org
Subject:   RE: vge(4) driver not working at 1G speeds
Message-ID:  <483f01c89493$4b8d8b90$e2a8a2b0$@net>
In-Reply-To: <20080402002729.GA18494@cdnetworks.co.kr>
References:  <0fc501c893c7$dfbf99b0$9f3ecd10$@net> <20080402002729.GA18494@cdnetworks.co.kr>

next in thread | previous in thread | raw e-mail | index | archive | help
Hi,
Here is the dmesg section, it appears to be using UKPHY so as you say if the
older chips used a different physical layer perhaps we have a problem in
there.

-- dmesg --
pci3: <ACPI PCI bus> on pcib3
vge0: <VIA Networking Gigabit Ethernet> port 0xe800-0xe8ff mem
0xfeaffc00-0xfeaffcff irq 28 at device 0.0 on pci3
miibus0: <MII bus> on vge0
ukphy0: <Generic IEEE 802.3u media interface> PHY 22 on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
vge0: using obsoleted if_watchdog interface
vge0: Ethernet address: 00:40:63:f3:7e:28
vge0: [ITHREAD]


rgds

Stu
-----Original Message-----
From: owner-freebsd-current@freebsd.org
[mailto:owner-freebsd-current@freebsd.org] On Behalf Of Pyun YongHyeon
Sent: 02 April 2008 01:27
To: Stuart Fraser
Cc: freebsd-current@freebsd.org
Subject: Re: vge(4) driver not working at 1G speeds

On Tue, Apr 01, 2008 at 08:13:19AM +0100, Stuart Fraser wrote:
 > Hi,
 > I'm trying to get a Via Velocity Gigabit Networking driver vge(4) to work
at
 > 1000baseTX on a Via EPIA SN18000 Motherboard.
 > 
 > It will always Auto negotiation and back-off to 100MB Full duplex, which
 > works
 > Perfectly (so far). When I try to manually force the card 1000baseTX the
 > interface
 > status reports 'no carrier' and I can get not connectivity. I have tried
 > Ubuntu live disk and it works seamlessly to 1GB, so I'm sure the
 > cabling/switch etc is fine and the issue is with the driver.
 > 
 > So I have tried 1000baseTX full and half duplex. I have tried to disable
the
 > hardware handoff using the mediaopt commands -rxcsum and -txcsum. Further
I
 > have tried to use the link0 operation as described in the man page but I
 > get:
 > 
 > nas# ifconfig vge0 mediaopt link0
 > ifconfig: SIOCSIFMEDIA (media): Device not configured
 > 
 > Further I have tried Release 7.0 and Stable 7 with the vge driver
compiled
 > In to the kernel also as an external module loaded through
boot/loader.conf
 > and lastly waiting until a full boot has completed and manually loading
the
 > if_vge module.
 > 
 > The only thing I can see is that the chipset is actually a VT6130 and
 > perhaps the driver needs 'tweaked' or there is some sysctl somewhere to
poke
 > it into life. As I say it works fine in 100MB mode and I can use 100M for
a
 > while but I'm planning on using this as a NAS so 1G would be preferred.
 > 
 > Any help, suggestions, thoughts would be appreciated. Anyone got it
working
 > or tried?
 > Should I report it as a bug?
 > 

Would you show me verbosed boot message?
Old VIA VT6120/VT6122 controllers used to ciphy(4) but newer PCIe
Velocity gigabit controllers, VT6130/VT6132, might use other
variants of the PHY.

-- 
Regards,
Pyun YongHyeon
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"





Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?483f01c89493$4b8d8b90$e2a8a2b0$>