Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 20 Dec 2005 17:36:28 -0800
From:      Steve Kargl <sgk@troutmask.apl.washington.edu>
To:        freebsd-current@freebsd.org
Subject:   Extremely slow probe of fxp0?
Message-ID:  <20051221013628.GA653@troutmask.apl.washington.edu>

next in thread | raw e-mail | index | archive | help
I updated an Aug 24 2005 (not-so current) -current up to HEAD,
and have observed an extremely slow probe of fxp0 during boot
of an SMP AMD64 kernel.  The relevant lines from a verbose 
boot are

fxp0: <Intel 82551 Pro/100 Ethernet> port 0xa000-0xa03f mem 0xfeafa000-0xfeafaff
f,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on pci3
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafa000
fxp0: using memory space register mapping

(6.5 minutes or longer pause here)

fxp0: PCI IDs: 8086 1229 8086 1040 0010
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:e0:81:2a:59:e7
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51
fxp0: [MPSAFE]

The full dmesg follows the sig.

-- 
Steve


Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 7.0-CURRENT #0: Tue Dec 20 16:05:59 PST 2005
    root@troutmask.apl.washington.edu:/mnt1/obj/mnt1/src/sys/SPEW
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80746000.
ACPI APIC Table: <A M I  OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193046 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2193676782 Hz
CPU: AMD Opteron(tm) Processor 248 (2193.68-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0xf58  Stepping = 8
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
usable memory  = 12809666560 (12216 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x000000000084b000 - 0x00000000fbfeffff, 4219097088 bytes (1030053 pages)
0x0000000100000000 - 0x00000002e97bbfff, 8212168704 bytes (2004924 pages)
avail memory = 12420374528 (11844 MB)
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: Found IO APIC ID 3, Interrupt 24 at 0xfebff000
ioapic1: intpin 0 -> PCI IRQ 24 (level, low)
ioapic1: intpin 1 -> PCI IRQ 25 (level, low)
ioapic1: intpin 2 -> PCI IRQ 26 (level, low)
ioapic1: intpin 3 -> PCI IRQ 27 (level, low)
MADT: Found IO APIC ID 4, Interrupt 28 at 0xfebfe000
ioapic2: intpin 0 -> PCI IRQ 28 (level, low)
ioapic2: intpin 1 -> PCI IRQ 29 (level, low)
ioapic2: intpin 2 -> PCI IRQ 30 (level, low)
ioapic2: intpin 3 -> PCI IRQ 31 (level, low)
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00000000 err: 0x0001000f pcm: 0x00010000
mem: <memory>
null: <null device, zero device>
nfslock: pseudo-device
random: <entropy source, Software, Yarrow>
io: <I/O>
acpi0: <A M I OEMXSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80023000
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 1 2 3 4 5 6 [class=060400] [hdr=01] is there (id=74601022)
AcpiOsDerivePciId: bus 0 dev 7 func 0
AcpiOsDerivePciId: bus 0 dev 7 func 1
AcpiOsDerivePciId: bus 0 dev 7 func 3
acpi0: Power Button (fixed)
AcpiOsDerivePciId: bus 0 dev 10 func 0
AcpiOsDerivePciId: bus 0 dev 11 func 0
pci_link0: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   10   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   15   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   15   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0   11   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial probe:
Index  IRQ  Rtd  Ref  IRQs
    0    9   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial validation:
Index  IRQ  Rtd  Ref  IRQs
    0    9   N     0  3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after disable:
Index  IRQ  Rtd  Ref  IRQs
    0  255   N     0  3 4 5 6 7 9 10 11 12 14 15
ACPI timer: 1/2 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x5010
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found->	vendor=0x1022, dev=0x7460, revid=0x07
	bus=0, slot=6, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0117, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7468, revid=0x05
	bus=0, slot=7, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7469, revid=0x03
	bus=0, slot=7, func=1
	class=01-01-8a, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[20]: type 4, range 32, base 0000ffa0, size  4, port disabled
found->	vendor=0x1022, dev=0x746a, revid=0x02
	bus=0, slot=7, func=2
	class=0c-05-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0001, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=9
	map[10]: type 4, range 32, base 0000cc00, size  5, enabled
pcib0: matched entry for 0.7.INTD
pcib0: slot 7 INTD hardwired to IRQ 19
found->	vendor=0x1022, dev=0x746b, revid=0x05
	bus=0, slot=7, func=3
	class=06-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7450, revid=0x12
	bus=0, slot=10, func=0
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0117, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7451, revid=0x01
	bus=0, slot=10, func=1
	class=08-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 1, range 64, base febff000, size 12, enabled
found->	vendor=0x1022, dev=0x7450, revid=0x12
	bus=0, slot=11, func=0
	class=06-04-00, hdrtype=0x01, mfdev=1
	cmdreg=0x0116, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x7451, revid=0x01
	bus=0, slot=11, func=1
	class=08-00-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type 1, range 64, base febfe000, size 12, enabled
found->	vendor=0x1022, dev=0x1100, revid=0x00
	bus=0, slot=24, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1101, revid=0x00
	bus=0, slot=24, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1102, revid=0x00
	bus=0, slot=24, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1103, revid=0x00
	bus=0, slot=24, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1100, revid=0x00
	bus=0, slot=25, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1101, revid=0x00
	bus=0, slot=25, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1102, revid=0x00
	bus=0, slot=25, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1103, revid=0x00
	bus=0, slot=25, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pcib1:   secondary bus     3
pcib1:   subordinate bus   3
pcib1:   I/O decode        0x9000-0xbfff
pcib1:   memory decode     0xfc900000-0xfeafffff
pcib1:   prefetched decode 0xfff00000-0xfffff
pci3: <ACPI PCI bus> on pcib1
pci3: physical bus=3
found->	vendor=0x1022, dev=0x7464, revid=0x0b
	bus=3, slot=0, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
	intpin=d, irq=9
	map[10]: type 1, range 32, base feafc000, size 12, enabled
pcib1: (null) requested memory range 0xfeafc000-0xfeafcfff: good
pcib1: matched entry for 3.0.INTD
pcib1: slot 0 INTD hardwired to IRQ 19
found->	vendor=0x1022, dev=0x7464, revid=0x0b
	bus=3, slot=0, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
	intpin=d, irq=9
	map[10]: type 1, range 32, base feafd000, size 12, enabled
pcib1: (null) requested memory range 0xfeafd000-0xfeafdfff: good
pcib1: matched entry for 3.0.INTD
pcib1: slot 0 INTD hardwired to IRQ 19
found->	vendor=0x9004, dev=0x8178, revid=0x00
	bus=3, slot=4, func=0
	class=01-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0280, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
	intpin=a, irq=10
	map[10]: type 4, range 32, base 0000b400, size  8, enabled
pcib1: (null) requested I/O range 0xb400-0xb4ff: in range
	map[14]: type 1, range 32, base feafe000, size 12, enabled
pcib1: (null) requested memory range 0xfeafe000-0xfeafefff: good
pcib1: matched entry for 3.4.INTA
pcib1: slot 4 INTA hardwired to IRQ 16
found->	vendor=0x1095, dev=0x3114, revid=0x02
	bus=3, slot=5, func=0
	class=01-80-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=9
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 4, range 32, base 0000bc00, size  3, enabled
pcib1: (null) requested I/O range 0xbc00-0xbc07: in range
	map[14]: type 4, range 32, base 0000b000, size  2, enabled
pcib1: (null) requested I/O range 0xb000-0xb003: in range
	map[18]: type 4, range 32, base 0000ac00, size  3, enabled
pcib1: (null) requested I/O range 0xac00-0xac07: in range
	map[1c]: type 4, range 32, base 0000a800, size  2, enabled
pcib1: (null) requested I/O range 0xa800-0xa803: in range
	map[20]: type 4, range 32, base 0000a400, size  4, enabled
pcib1: (null) requested I/O range 0xa400-0xa40f: in range
	map[24]: type 1, range 32, base feafbc00, size 10, enabled
pcib1: (null) requested memory range 0xfeafbc00-0xfeafbfff: good
pcib1: matched entry for 3.5.INTA
pcib1: slot 5 INTA hardwired to IRQ 19
found->	vendor=0x1002, dev=0x4752, revid=0x27
	bus=3, slot=6, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib1: (null) requested memory range 0xfd000000-0xfdffffff: good
	map[14]: type 4, range 32, base 0000b800, size  8, enabled
pcib1: (null) requested I/O range 0xb800-0xb8ff: in range
	map[18]: type 1, range 32, base feaff000, size 12, enabled
pcib1: (null) requested memory range 0xfeaff000-0xfeafffff: good
pcib1: matched entry for 3.6.INTA
pcib1: slot 6 INTA hardwired to IRQ 18
found->	vendor=0x8086, dev=0x1229, revid=0x10
	bus=3, slot=8, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
	intpin=a, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type 1, range 32, base feafa000, size 12, enabled
pcib1: (null) requested memory range 0xfeafa000-0xfeafafff: good
	map[14]: type 4, range 32, base 0000a000, size  6, enabled
pcib1: (null) requested I/O range 0xa000-0xa03f: in range
	map[18]: type 1, range 32, base feaa0000, size 17, enabled
pcib1: (null) requested memory range 0xfeaa0000-0xfeabffff: good
pcib1: matched entry for 3.8.INTA
pcib1: slot 8 INTA hardwired to IRQ 18
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 19 at device 0.0 on pci3
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafc000
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 49
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfeafd000-0xfeafdfff irq 19 at device 0.1 on pci3
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafd000
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xb400-0xb4ff mem 0xfeafe000-0xfeafefff irq 16 at device 4.0 on pci3
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xb400
ahc0: Enabling 39Bit Addressing
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 450 instructions downloaded
ahc0: Features 0x10001, Bugs 0x25, Flags 0x21481540
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 50
ahc0: [GIANT-LOCKED]
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
pci3: <mass storage> at device 5.0 (no driver attached)
vgapci0: <VGA-compatible display> port 0xb800-0xb8ff mem 0xfd000000-0xfdffffff,0xfeaff000-0xfeafffff irq 18 at device 6.0 on pci3
fxp0: <Intel 82551 Pro/100 Ethernet> port 0xa000-0xa03f mem 0xfeafa000-0xfeafafff,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on pci3
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafa000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 1040 0010
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:e0:81:2a:59:e7
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51
fxp0: [MPSAFE]
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <mass storage, ATA> at device 7.1 (no driver attached)
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
amdpm0: <AMD 756/766/768/8111 Power Management Controller> port 0x50e0-0x50ff at device 7.3 on pci0
smbus0: <System Management Bus> on amdpm0
smb0: <SMBus generic I/O> on smbus0
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0x8000-0x8fff
pcib2:   memory decode     0xfc600000-0xfc8fffff
pcib2:   prefetched decode 0xff500000-0xff5fffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found->	vendor=0x9005, dev=0x801d, revid=0x10
	bus=2, slot=6, func=0
	class=01-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0117, statreg=0x0430, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	MSI supports 2 messages, 64 bit
	map[10]: type 4, range 32, base 00008000, size  8, enabled
pcib2: (null) requested I/O range 0x8000-0x80ff: in range
	map[14]: type 1, range 64, base fc8fc000, size 13, enabled
pcib2: (null) requested memory range 0xfc8fc000-0xfc8fdfff: good
	map[1c]: type 4, range 32, base 00008c00, size  8, enabled
pcib2: (null) requested I/O range 0x8c00-0x8cff: in range
pcib2: matched entry for 2.6.INTA
pcib2: slot 6 INTA hardwired to IRQ 24
found->	vendor=0x9005, dev=0x801d, revid=0x10
	bus=2, slot=6, func=1
	class=01-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0117, statreg=0x0430, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
	intpin=b, irq=15
	powerspec 2  supports D0 D3  current D0
	MSI supports 2 messages, 64 bit
	map[10]: type 4, range 32, base 00008800, size  8, enabled
pcib2: (null) requested I/O range 0x8800-0x88ff: in range
	map[14]: type 1, range 64, base fc8fe000, size 13, enabled
pcib2: (null) requested memory range 0xfc8fe000-0xfc8fffff: good
	map[1c]: type 4, range 32, base 00008400, size  8, enabled
pcib2: (null) requested I/O range 0x8400-0x84ff: in range
pcib2: matched entry for 2.6.INTB
pcib2: slot 6 INTB hardwired to IRQ 25
ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x8000-0x80ff,0x8c00-0x8cff mem 0xfc8fc000-0xfc8fdfff irq 24 at device 6.0 on pci2
ahd0: Defaulting to MEMIO on
ahd0: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfc8fc000
ahd0: Enabling 39Bit Addressing
ahd0: Reading VPD from SEEPROM...ahd0: VPD parsing successful
ahd0: Reading SEEPROM...done.
ahd0: STPWLEVEL is on
ahd0: Manual Primary Termination
ahd0: Manual Secondary Termination
ahd0: Primary High byte termination Enabled
ahd0: Primary Low byte termination Enabled
ahd0: Secondary High byte termination Disabled
ahd0: Secondary Low byte termination Disabled
ahd0: Downloading Sequencer Program... 697 instructions downloaded
ahd0: Features 0x3c101, Bugs 0x740002, Flags 0x143f1
ioapic1: routing intpin 0 (PCI IRQ 24) to vector 52
ahd0: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x8800-0x88ff,0x8400-0x84ff mem 0xfc8fe000-0xfc8fffff irq 25 at device 6.1 on pci2
ahd1: Defaulting to MEMIO on
ahd1: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfc8fe000
ahd1: Enabling 39Bit Addressing
ahd1: Reading VPD from SEEPROM...ahd1: VPD parsing successful
ahd1: Reading SEEPROM...done.
ahd1: STPWLEVEL is on
ahd1: Manual Primary Termination
ahd1: Manual Secondary Termination
ahd1: Primary High byte termination Enabled
ahd1: Primary Low byte termination Enabled
ahd1: Secondary High byte termination Disabled
ahd1: Secondary Low byte termination Disabled
ahd1: Downloading Sequencer Program... 697 instructions downloaded
ahd1: Features 0x3c101, Bugs 0x740002, Flags 0x143f0
ioapic1: routing intpin 1 (PCI IRQ 25) to vector 53
ahd1: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pcib3:   secondary bus     1
pcib3:   subordinate bus   1
pcib3:   I/O decode        0x0-0x0
pcib3:   memory decode     0xfff00000-0xfffff
pcib3:   prefetched decode 0xfff00000-0xfffff
pci1: <ACPI PCI bus> on pcib3
pci1: physical bus=1
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 54
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to vector 55
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 57
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 58
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ioapic0: routing intpin 7 (ISA IRQ 7) to vector 59
acpi_hpet0: <HPET - High Precision Event Timers> iomem 0xfec01000-0xfec013ff irq 0,8 on acpi0
acpi_hpet0: Vendor: 0x1022
acpi_hpet0: Leg_Route_Cap: 1
acpi_hpet0: Count_Size_Cap: 0
acpi_hpet0: Num_Tim_Cap: 8
acpi_hpet0: Rev_id: 0x3
acpi_hpet0: Period: 69841279 fs (14318180 Hz)
acpi_hpet0: HPET attach
Timecounter "HPET" frequency 14318180 Hz quality -200
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 8: ioport 0x8c00 alloc failed
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcc7ff,0xd5800-0xd9fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <8 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Reducing kern.maxvnodes 243854 -> 100000
procfs registered
linprocfs registered
lapic: Divisor 2, Frequency 99712590 hz
Timecounter "TSC" frequency 2193676782 Hz quality -100
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
Waiting 3 seconds for SCSI devices to settle
(noperiph:ahd0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(noperiph:ahd1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
ahd0: Selection Timeout on A:3. 0 SCBs aborted
ahd1: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
ahd0: Selection Timeout on A:4. 0 SCBs aborted
ahd1: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
ahd0: Selection Timeout on A:5. 0 SCBs aborted
ahd1: Selection Timeout on A:3. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahd0: Selection Timeout on A:11. 0 SCBs aborted
ahd1: Selection Timeout on A:4. 0 SCBs aborted
ahc0: Selection Timeout on A:2. 0 SCBs aborted
(probe15:ahc0:0:0:0): Retrying Command
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ahc0: target 4 synchronous at 10.0MHz, offset = 0xf
(ahc0:A:5:0): Sending SDTR period 19, offset f
(ahc0:A:5:0): Received SDTR period 32, offset f
	Filtered to period 32, offset f
ahc0: target 5 synchronous at 5.0MHz, offset = 0xf
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:5:0): Sending SDTR period 32, offset f
(ahc0:A:5:0): Received SDTR period 32, offset f
	Filtered to period 32, offset f
(ahc0:A:0:0): Sending SDTR period 19, offset f
(ahc0:A:0:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ahc0: target 0 synchronous at 10.0MHz, offset = 0xf
ahd0: Selection Timeout on A:12. 0 SCBs aborted
ahd1: Selection Timeout on A:5. 0 SCBs aborted
ahd0: Selection Timeout on A:13. 0 SCBs aborted
ahd1: Selection Timeout on A:6. 0 SCBs aborted
ahd0: Selection Timeout on A:1. 0 SCBs aborted
ahd1: Selection Timeout on A:8. 0 SCBs aborted
ahd0: Selection Timeout on A:2. 0 SCBs aborted
ahd1: Selection Timeout on A:9. 0 SCBs aborted
ahd0: Selection Timeout on A:6. 0 SCBs aborted
ahd1: Selection Timeout on A:10. 0 SCBs aborted
ahd0: Selection Timeout on A:8. 0 SCBs aborted
ahd1: Selection Timeout on A:11. 0 SCBs aborted
ahd0: Selection Timeout on A:9. 0 SCBs aborted
ahd1: Selection Timeout on A:12. 0 SCBs aborted
ahd0: Selection Timeout on A:10. 0 SCBs aborted
ahd1: Selection Timeout on A:13. 0 SCBs aborted
ahd0: Selection Timeout on A:14. 0 SCBs aborted
ahd1: Selection Timeout on A:14. 0 SCBs aborted
ahd0: Selection Timeout on A:15. 0 SCBs aborted
(probe0:ahd0:0:0:0): Retrying Command
(ahd0:A:0:0): Sending PPR bus_width 1, period 8, offset fe, ppr_options ff
ahd1: Selection Timeout on A:15. 0 SCBs aborted
(ahd0:A:0:0): Received PPR width 1, period 8, offset 3f,options ff
	Filtered to width 1, period 8, offset 3f, options ff
ahd0: target 0 using 16bit transfers
ahd0: target 0 synchronous with period = 0x8, offset = 0x3f(RDSTRM|DT|IU|RTI|QAS)
ahd1: Selection Timeout on A:2. 0 SCBs aborted
pass0 at ahd0 bus 0 target 0 lun 0
pass0: <SEAGATE ST373307LW 0007> Fixed Direct Access SCSI-3 device 
pass0: Serial Number 3HZ805ZE00007436F79B
pass0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 0 lun 0
pass1: <SEAGATE ST39216N 0010> Fixed Direct Access SCSI-3 device 
pass1: Serial Number 3BN12XT600007124NH7V
pass1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
pass2 at ahc0 bus 0 target 4 lun 0
pass2: <PLEXTOR CD-R   PX-W4012S 1.01> Removable CD-ROM SCSI-2 device 
pass2: Serial Number 3
pass2: 10.000MB/s transfers (10.000MHz, offset 15)
pass3 at ahc0 bus 0 target 5 lun 0
pass3: <DEC DLT2000 8B37> Removable Sequential Access SCSI-2 device 
pass3: Serial Number CX837T0309
pass3: 5.000MB/s transfers (5.000MHz, offset 15)
sa0 at ahc0 bus 0 target 5 lun 0
sa0: <DEC DLT2000 8B37> Removable Sequential Access SCSI-2 device 
sa0: Serial Number CX837T0309
sa0: 5.000MB/s transfers (5.000MHz, offset 15)
da1 at ahc0 bus 0 target 0 lun 0
da1: <SEAGATE ST39216N 0010> Fixed Direct Access SCSI-3 device 
da1: Serial Number 3BN12XT600007124NH7V
da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da1: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
da0 at ahd0 bus 0 target 0 lun 0
da0: <SEAGATE ST373307LW 0007> Fixed Direct Access SCSI-3 device 
da0: Serial Number 3HZ805ZE00007436F79B
da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled
da0: 70007MB (143374744 512 byte sectors: 255H 63S/T 8924C)
GEOM: new disk da0(ahc0:A:4:0): Sending SDTR period 19, offset f

GEOM: n(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ew disk da1(cd0:ahc0:0:4:0): Retrying Command

GEOM: new disk cd0
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000200ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0
ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0
ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0
ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0
ioapic1: routing intpin 0 (PCI IRQ 24) to cluster 0
ioapic1: routing intpin 1 (PCI IRQ 25) to cluster 0
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
cd0 at ahc0 bus 0 target 4 lun 0
cd0: <PLEXTOR CD-R   PX-W4012S 1.01> Removable CD-ROM SCSI-2 device 
cd0: Serial Number 3
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: cd present [190950 x 2048 byte records]
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): CAM Status: SCSI Status Error
(cd0:ahc0:0:4:0): SCSI Status: Check Condition
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
(cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
Unretryable error
(cd0:ahc0:0:4:0): error 6
(cd0:ahc0:0:4:0): Unretryable Error
(cd0:ahc0:0:4:0): cddone: got error 0x6 back
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0 
(cd0:ahc0:0:4:0): CAM Status: SCSI Status Error
(cd0:ahc0:0:4:0): SCSI Status: Check Condition
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
(cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0 
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
Unretryable error
(cd0:ahc0:0:4:0): error 6
(cd0:ahc0:0:4:0): Unretryable Error
(cd0:ahc0:0:4:0): cddone: got error 0x6 back
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): CAM Status: SCSI Status Error
(cd0:ahc0:0:4:0): SCSI Status: Check Condition
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
(cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
Unretryable error
(cd0:ahc0:0:4:0): error 6
(cd0:ahc0:0:4:0): Unretryable Error
(cd0:ahc0:0:4:0): cddone: got error 0x6 back
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): CAM Status: SCSI Status Error
(cd0:ahc0:0:4:0): SCSI Status: Check Condition
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
(cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 
(cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0
(cd0:ahc0:0:4:0): Illegal mode for this track
Unretryable error
(cd0:ahc0:0:4:0): error 6
(cd0:ahc0:0:4:0): Unretryable Error
(cd0:ahc0:0:4:0): cddone: got error 0x6 back
Trying to mount root from ufs:/dev/da0s1a
start_init: trying /sbin/init
(da0:ahd0:0:0:0): Request Requeued
(da0:ahd0:0:0:0): Retrying Command
(da0:ahd0:0:0:0): Queue Full
(da0:ahd0:0:0:0): tagged openings now 63
(da0:ahd0:0:0:0): Retrying Command



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051221013628.GA653>