Date: Thu, 14 Dec 2000 16:32:40 -0800 From: noah <noah@indymedia.org> To: freebsd-scsi@freebsd.org Cc: Micah Anderson <micah@indymedia.org> Subject: Re: update Message-ID: <20001214163240.C25983@indymedia.org> In-Reply-To: <20001214092814.K11687@riseup.net>; from micah@indymedia.org on Thu, Dec 14, 2000 at 09:28:14AM -0800 References: <20001212233150.F11687@riseup.net> <20001213072136.B25257@indymedia.org> <20001214092814.K11687@riseup.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, I'm working on trying to install FreeBSD 4.2 on a dual p3 700 with an Adaptec 3200S raid card. From what I can tell everyone that has tried this card has had good luck. When we install FreeBSD (booting off cd) it recognizes the card and installs on it perfectly, but when it loads the OS off the raid it does something to damage the hardware raid, requiring us to rebuild the RAID in the 3200S' bios. We're pretty sure that this isn't a hardware problem. I've included a verbose copy of the boot up. Thanks for any help. > Where the raid dies is after the line, "asr0: major=154" - > > Copyright (c) 1992-2000 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.2-RELEASE #0: Mon Nov 20 13:02:55 GMT 2000 > jkh@bento.FreeBSD.org:/usr/src/sys/compile/GENERIC > Calibrating clock(s) ... TSC clock: 697068092 Hz, i8254 clock: 1193349 Hz > CLK_USE_I8254_CALIBRATION not specified - using default frequency > Timecounter "i8254" frequency 1193182 Hz > CLK_USE_TSC_CALIBRATION not specified - using old calibration method > CPU: Pentium III/Pentium III Xeon/Celeron (696.97-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x683 Stepping = 3 > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536805376 (524224K bytes) > Physical memory chunk(s): > 0x00001000 - 0x0009efff, 647168 bytes (158 pages) > 0x0044f000 - 0x1ffe7fff, 532254720 bytes (129945 pages) > avail memory = 518422528 (506272K bytes) > bios32: Found BIOS32 Service Directory header at 0xc00f6c30 > bios32: Entry = 0xfd7e3 (c00fd7e3) Rev = 0 Len = 1 > pcibios: PCI BIOS entry at 0x430 > pnpbios: Found PnP BIOS data at 0xc00f6c60 > pnpbios: Entry = f0000:a8cb Rev = 1.0 > Other BIOS signatures found: > ACPI: 000f6ad0 > Preloaded elf kernel "kernel" at 0xc0436000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Creating DISK md0 > Math emulator present > pci_open(1): mode 1 addr port (0x0cf8) is 0x80022108 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71a08086) > pcib-: pcib0 exists, using next available unit number > npx0: <math processor> on motherboard > npx0: INT 16 interface > pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71a08086) > pcib0: <Intel 82443GX host to PCI bridge> on motherboard > found-> vendor=0x8086, dev=0x71a0, revid=0x00 > class=06-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[10]: type 1, range 32, base f8000000, size 26 > found-> vendor=0x8086, dev=0x71a1, revid=0x00 > class=06-04-00, hdrtype=0x01, mfdev=0 > subordinatebus=3 secondarybus=1 > found-> vendor=0x9005, dev=0x005f, revid=0x00 > class=01-00-00, hdrtype=0x00, mfdev=1 > subordinatebus=0 secondarybus=0 > intpin=a, irq=11 > map[10]: type 1, range 32, base 00002000, size 8 > map[14]: type 1, range 64, base f4100000, size 12 > found-> vendor=0x9005, dev=0x005f, revid=0x00 > class=01-00-00, hdrtype=0x00, mfdev=1 > subordinatebus=0 secondarybus=0 > intpin=a, irq=11 > map[10]: type 1, range 32, base 00002400, size 8 > map[14]: type 1, range 64, base f4101000, size 12 > found-> vendor=0x8086, dev=0x1229, revid=0x08 > class=02-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=a, irq=10 > map[10]: type 1, range 32, base f4102000, size 12 > map[14]: type 1, range 32, base 00002800, size 6 > map[18]: type 1, range 32, base f4000000, size 20 > found-> vendor=0x8086, dev=0x7110, revid=0x02 > class=06-01-00, hdrtype=0x00, mfdev=1 > subordinatebus=0 secondarybus=0 > found-> vendor=0x8086, dev=0x7111, revid=0x01 > class=01-01-80, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[20]: type 1, range 32, base 00002860, size 4 > found-> vendor=0x8086, dev=0x7112, revid=0x01 > class=0c-03-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=d, irq=10 > map[20]: type 1, range 32, base 00002840, size 5 > found-> vendor=0x8086, dev=0x7113, revid=0x02 > class=06-80-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[90]: type 1, range 32, base 00001040, size 4 > found-> vendor=0x1013, dev=0x00bc, revid=0x23 > class=03-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[10]: type 1, range 32, base f6000000, size 25 > map[14]: type 1, range 32, base f4103000, size 12 > pci0: <PCI bus> on pcib0 > pcib2: <Intel 82443GX (440 GX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 > found-> vendor=0x1011, dev=0x0023, revid=0x06 > class=06-04-00, hdrtype=0x01, mfdev=0 > subordinatebus=3 secondarybus=2 > pci1: <PCI bus> on pcib2 > pcib3: <PCI to PCI bridge (vendor=1011 device=0023)> at device 15.0 on pci1 > found-> vendor=0x1044, dev=0xa500, revid=0x02 > class=06-04-00, hdrtype=0x01, mfdev=1 > subordinatebus=3 secondarybus=3 > found-> vendor=0x1044, dev=0xa501, revid=0x02 > class=0e-00-01, hdrtype=0x00, mfdev=1 > subordinatebus=0 secondarybus=0 > intpin=a, irq=5 > map[10]: type 1, range 32, base fc000000, size 25 > pci2: <PCI bus> on pcib3 > pcib4: <PCI to PCI bridge (vendor=1044 device=a500)> at device 4.0 on pci2 > pci3: <PCI bus> on pcib4 > asr0: <Adaptec Caching SCSI RAID> mem 0xfc000000-0xfdffffff irq 5 at device 4.1 on pci2 > asr0: major=154 > asr0: ADAPTEC 3200S FW Rev. 320P, 2 channel, 256 CCBs, Protocol I2O > ahc0: <Adaptec aic7896/97 Ultra2 SCSI adapter> port 0x2000-0x20ff mem 0xf4100000-0xf4100fff irq 11 at device 12.0 on pci0 > ahc0: Reading SEEPROM...done. > ahc0: Manual LVD Termination > ahc0: BIOS eeprom is present > ahc0: Secondary High byte termination Enabled > ahc0: Secondary Low byte termination Enabled > ahc0: Primary Low Byte termination Enabled > ahc0: Primary High Byte termination Enabled > ahc0: Downloading Sequencer Program... 412 instructions downloaded > aic7896/97: Wide Channel A, SCSI Id=7, 32/255 SCBs > ahc1: <Adaptec aic7896/97 Ultra2 SCSI adapter> port 0x2400-0x24ff mem 0xf4101000-0xf4101fff irq 11 at device 12.1 on pci0 > ahc1: Reading SEEPROM...done. > ahc1: Manual LVD Termination > ahc1: BIOS eeprom is present > ahc1: Secondary High byte termination Enabled > ahc1: Secondary Low byte termination Enabled > ahc1: Primary Low Byte termination Enabled > ahc1: Primary High Byte termination Enabled > ahc1: Downloading Sequencer Program... 412 instructions downloaded > aic7896/97: Wide Channel B, SCSI Id=7, 32/255 SCBs > using shared irq11. > fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2800-0x283f mem 0xf4000000-0xf40fffff,0xf4102000-0xf4102fff irq 10 at device 14.0 on pci0 > fxp0: Ethernet address 00:d0:b7:a9:34:0c > bpf: fxp0 attached > isab0: <Intel 82371AB PCI to ISA bridge> at device 18.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 ATA33 controller> port 0x2860-0x286f at device 18.1 on pci0 > ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x2860 > ata0: mask=03 status0=00 status1=00 > ata0: mask=03 ostat0=00 ostat2=00 > ata0-master: ATAPI probe a=00 b=00 > ata0-slave: ATAPI probe a=00 b=00 > ata0: mask=03 status0=00 status1=00 > ata0: devices=00 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x2868 > ata1: mask=03 status0=00 status1=00 > ata1: mask=03 ostat0=00 ostat2=00 > ata1-master: ATAPI probe a=00 b=00 > ata1-slave: ATAPI probe a=00 b=00 > ata1: mask=03 status0=00 status1=00 > ata1: devices=00 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x2840-0x285f irq 10 at device 18.2 on pci0 > using shared irq10. > usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > chip1: <Intel 82371AB Power management controller> port 0x1040-0x104f at device 18.3 on pci0 > pci0: <Cirrus Logic GD5480 SVGA controller> (vendor=0x1013, dev=0x00bc) at 20.0 > pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71a08086) > pci-: pci1 exists, using next available unit number > pcib1: <Intel 82443GX host to AGP bridge> on motherboard > pci4: <PCI bus> on pcib1 > ata-: ata0 exists, using next available unit number > ata-: ata1 exists, using next available unit number > Trying Read_Port at 203 > Trying Read_Port at 243 > Trying Read_Port at 283 > Trying Read_Port at 2c3 > Trying Read_Port at 303 > Trying Read_Port at 343 > Trying Read_Port at 383 > Trying Read_Port at 3c3 > isa_probe_children: disabling PnP devices > isa_probe_children: probing non-PnP devices > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ata2 failed to probe at port 0x1f0 irq 14 on isa0 > ata3 failed to probe at port 0x170 irq 15 on isa0 > adv0 failed to probe at port 0x330 on isa0 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x330 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x334 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x230 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x234 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x130 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x134 > bt0 failed to probe at port 0x134-0x137 on isa0 > aha0: status reg test failed ff > aha0: status reg test failed ff > aha0: status reg test failed ff > aha0: status reg test failed ff > aha0: status reg test failed ff > aha0: status reg test failed ff > aha0 failed to probe at port 0x134-0x137 on isa0 > aic0 failed to probe at port 0x140-0x15f on isa0 > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > atkbd: the current kbd controller command byte 0047 > atkbd: keyboard ID 0x41ab (2) > kbdc: RESET_KBD return code:00fa > kbdc: RESET_KBD status:00aa > kbd0 at atkbd0 > kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 > psm0: current command byte:0047 > kbdc: TEST_AUX_PORT status:0000 > kbdc: RESET_AUX return code:00fe > kbdc: RESET_AUX return code:00fe > kbdc: RESET_AUX return code:00fe > kbdc: DIAGNOSE status:0055 > kbdc: TEST_KBD_PORT status:0000 > psm0: failed to reset the aux device. > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > fb0: vga0, vga, type:VGA (5), flags:0x7007f > fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 > fb0: init mode:24, bios mode:3, current mode:24 > fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k > VGA parameters upon power-up > 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > VGA parameters in BIOS for mode 24 > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > EGA/VGA parameters to be used for mode 24 > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) > pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 > pcic1: not probed (disabled) > sio0: irq maps: 0x41 0x51 0x41 0x41 > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: irq maps: 0x41 0x41 0x41 0x41 > sio1: probe failed test(s): 0 1 2 4 6 7 9 > sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 > sio2: not probed (disabled) > sio3: not probed (disabled) > ppc0: parallel port found at 0x378 > ppc0: using extended I/O port range > ppc0: ECP SPP SPP > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > bpf: lp0 attached > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > ed0 failed to probe at port 0x280-0x29f iomem 0xd8000 irq 10 on isa0 > fe0 failed to probe at port 0x300-0x31f on isa0 > ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0 > lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0 > cs0 failed to probe at port 0x300 on isa0 > sn0 failed to probe at port 0x300 irq 10 on isa0 > isa_probe_children: probing PnP devices > BIOS Geometries: > 0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors > 0 accounted for > Device configuration finished. > bpf: faith0 attached > bpf: gif0 attached > bpf: gif1 attached > bpf: gif2 attached > bpf: gif3 attached > bpf: lo0 attached > bpf: ppp0 attached > new masks: bio 68c440, tty 630092, net 670492 > bpf: sl0 attached > Waiting 15 seconds for SCSI devices to settle > (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. > (noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. > Creating DISK da0 > Creating DISK da1 > pass0 at asr0 bus 0 target 1 lun 0 > pass0: <ADAPTEC RAID-5 320P> Fixed Direct Access SCSI-2 device > pass0: Serial Number + > pass0: Tagged Queueing Enabled > pass1 at asr0 bus 0 target 3 lun 0 > pass1: <IBM DDYS-T09170N S80D> Fixed Direct Access SCSI-3 device > pass1: Serial Number 4DY1M466 > pass1: Tagged Queueing Enabled > da0 at asr0 bus 0 target 1 lun 0 > da0: <ADAPTEC RAID-5 320P> Fixed Direct Access SCSI-2 device > da0: Serial Number + > da0: Tagged Queueing Enabled > da0: 17496MB (35831808 512 byte sectors: 255H 63S/T 2230C) > da1 at asr0 bus 0 target 3 lun 0 > da1: <IBM DDYS-T09170N S80D> Fixed Direct Access SCSI-3 device > da1: Serial Number 4DY1M466 > da1: Tagged Queueing Enabled > da1: 8748MB (17916240 512 byte sectors: 255H 63S/T 1115C) > Mounting root from ufs:/dev/da0s1a > da0s1: type 0xa5, start 63, end = 35824949, size 35824887 : OK > start_init: trying /sbin/init -- noah .. email for pgp/gpg key To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20001214163240.C25983>