Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 16 Mar 2004 10:33:02 +0200
From:      "Emil Cazamir" <emil.cazamir@galati.rdsnet.ro>
To:        "'Peter Olsson'" <pol@leissner.se>, <freebsd-current@freebsd.org>
Subject:    RE: 5.2.1-RELEASE boot-hang with Cyclades pci card Cyclom-16YeP/RJ45
Message-ID:  <20040316082912.A1B1A43D2F@mx1.FreeBSD.org>
In-Reply-To: <20040315211204.U1455@pol.leissner.se>

next in thread | previous in thread | raw e-mail | index | archive | help
This is a multi-part message in MIME format.

------=_NextPart_000_00AA_01C40B42.129F66C0
Content-Type: text/plain;
	charset="us-ascii"
Content-Transfer-Encoding: 7bit

Hello

I tried to use same family hardware and I had no luck with RELENG_5. I had
to revert to RELENG_4... I stuck in the "hung" phase, didn't tested with the
cable detached. Anyway, what's the sense of using a Cyclom-Y without the
external connectors?
See the attachments (dmesg & kernel configuration file)

Best regards,
Emil Cazamir

-----Original Message-----
From: owner-freebsd-current@freebsd.org
[mailto:owner-freebsd-current@freebsd.org] On Behalf Of Peter Olsson
Sent: 15 martie 2004 22:24
To: freebsd-current@freebsd.org
Subject: 5.2.1-RELEASE boot-hang with Cyclades pci card Cyclom-16YeP/RJ45

Hello!

We use several Cyclades port cards in FreeBSD 4.x.
I tried upgrading one of the servers to 5.2.1 this week, but
it just hung after recognizing the Cyclades card during boot.
If I disconnected the external cable from the pci card the boot went
fine, so it seems that it was some scanning of the external port card
that generated the problem.

Here are the boot messages just before the boot process hung:
cy0: <Cyclades Cyclom-Y Serial Adapter> port 0xa400-0xa47f
 mem 0xd0034000-0xd0037fff, 0xd0039000-0xd003907f irq 18 at
 device 10.0 on pci1
pcib1: device cy0 requested decoded I/O range 0xa400-0xa47f
pcib1: device cy0 requested decoded memory range 0xd0034000-0xd0037fff

Is anyone using Cyclades port cards in 5.2.1?

Is there some way to get rid of the need to include COMPAT_OLDISA for
the cyclades driver (is there some way to make a separate pci driver or
just strip the isa code from the driver)?

Thanks!

-- 
Peter Olsson             pol@leissner.se
CCIE #8963               +46 520 500511
Leissner Data AB         +46 701 809511
_______________________________________________
freebsd-current@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"

------=_NextPart_000_00AA_01C40B42.129F66C0
Content-Type: text/plain;
	name="kernconf.txt"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="kernconf.txt"

#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#    http://www.FreeBSD.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you =
are
# in doubt as to the purpose or necessity of a line, check first in =
LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.38 2002/01/25 17:41:40 =
murray Exp $

machine		i386
#cpu		I386_CPU
#cpu		I486_CPU
cpu		I586_CPU
cpu		I686_CPU
ident		INTFOR
maxusers	32

#makeoptions	DEBUG=3D-g		#Build kernel with gdb(1) debug symbols

#options 	MATH_EMULATE		#Support for x87 emulation
options 	INET			#InterNETworking
options 	INET6			#IPv6 communications protocols
options 	FFS			#Berkeley Fast Filesystem
options 	FFS_ROOT		#FFS usable as root device [keep this!]
options 	SOFTUPDATES		#Enable FFS soft updates support
options 	UFS_DIRHASH		#Improve performance on big directories
options 	MFS			#Memory Filesystem
options 	MD_ROOT			#MD is a potential root device
options 	NFS			#Network Filesystem
options 	NFS_ROOT		#NFS usable as root device, NFS required
options 	MSDOSFS			#MSDOS Filesystem
options 	CD9660			#ISO 9660 Filesystem
options 	CD9660_ROOT		#CD-ROM usable as root, CD9660 required
options 	PROCFS			#Process filesystem
options 	COMPAT_43		#Compatible with BSD 4.3 [KEEP THIS!]
options 	SCSI_DELAY=3D15000	#Delay (in ms) before probing SCSI
options 	UCONSOLE		#Allow users to grab the console
options 	USERCONFIG		#boot -c editor
options 	VISUAL_USERCONFIG	#visual boot -c editor
options 	KTRACE			#ktrace(1) support
options 	SYSVSHM			#SYSV-style shared memory
options 	SYSVMSG			#SYSV-style message queues
options 	SYSVSEM			#SYSV-style semaphores
options 	P1003_1B		#Posix P1003_1B real-time extensions
options 	_KPOSIX_PRIORITY_SCHEDULING
options		ICMP_BANDLIM		#Rate limit bad replies
options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev

# To make an SMP kernel, the next two are needed
#options 	SMP			# Symmetric MultiProcessor Kernel
#options 	APIC_IO			# Symmetric (APIC) I/O

device		isa
#device		eisa
device		pci

# Floppy drives
device		fdc0	at isa? port IO_FD1 irq 6 drq 2
device		fd0	at fdc0 drive 0
#device		fd1	at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device		fdc0

# ATA and ATAPI devices
device		ata0	at isa? port IO_WD1 irq 14
device		ata1	at isa? port IO_WD2 irq 15
device		ata
device		atadisk			# ATA disk drives
device		atapicd			# ATAPI CDROM drives
#device		atapifd			# ATAPI floppy drives
#device		atapist			# ATAPI tape drives
options 	ATA_STATIC_ID		#Static device numbering

# SCSI Controllers
device		ahb		# EISA AHA1742 family
device		ahc		# AHA2940 and onboard AIC7xxx devices
device		amd		# AMD 53C974 (Tekram DC-390(T))
device		isp		# Qlogic family
device		ncr		# NCR/Symbios Logic
device		sym		# NCR/Symbios Logic (newer chipsets)
options		SYM_SETUP_LP_PROBE_MAP=3D0x40
				# Allow ncr to attach legacy NCR devices when=20
				# both sym and ncr are configured

device		adv0	at isa?
device		adw
device		bt0	at isa?
device		aha0	at isa?
device		aic0	at isa?

device		ncv		# NCR 53C500
device		nsp		# Workbit Ninja SCSI-3
device		stg		# TMC 18C30/18C50

# SCSI peripherals
device		scbus		# SCSI bus (required)
device		da		# Direct Access (disks)
device		sa		# Sequential Access (tape etc)
device		cd		# CD
device		pass		# Passthrough device (direct SCSI access)

# RAID controllers interfaced to the SCSI subsystem
device		asr		# DPT SmartRAID V, VI and Adaptec SCSI RAID
device		dpt		# DPT Smartcache - See LINT for options!
device		mly		# Mylex AcceleRAID/eXtremeRAID

# RAID controllers
device		aac		# Adaptec FSA RAID, Dell PERC2/PERC3
device		ida		# Compaq Smart RAID
device		amr		# AMI MegaRAID
device		mlx		# Mylex DAC960 family
device		twe		# 3ware Escalade

# atkbdc0 controls both the keyboard and the PS/2 mouse
device		atkbdc0	at isa? port IO_KBD
device		atkbd0	at atkbdc? irq 1 flags 0x1
device		psm0	at atkbdc? irq 12

device		vga0	at isa?

# splash screen/screen saver
pseudo-device	splash

# syscons is the default console driver, resembling an SCO console
device		sc0	at isa? flags 0x100

# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device		vt0	at isa?
#options 	XSERVER			# support for X server on a vt console
#options 	FAT_CURSOR		# start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT =
lines
#options 	PCVT_SCANSET=3D2		# IBM keyboards are non-std

# Floating point support - do not disable.
device		npx0	at nexus? port IO_NPX irq 13

# Power management support (see LINT for more options)
device		apm0    at nexus? disable flags 0x20 # Advanced Power Management

# PCCARD (PCMCIA) support
device		card
device		pcic0	at isa? irq 0 port 0x3e0 iomem 0xd0000
device		pcic1	at isa? irq 0 port 0x3e2 iomem 0xd4000 disable

# Serial (COM) ports
device		sio0	at isa? port IO_COM1 flags 0x10 irq 4
device		sio1	at isa? port IO_COM2 irq 3
device		sio2	at isa? disable port IO_COM3 irq 5
device		sio3	at isa? disable port IO_COM4 irq 9

# Parallel port
device		ppc0	at isa? irq 7
device		ppbus		# Parallel port bus (required)
device		lpt		# Printer
device		plip		# TCP/IP over parallel
device		ppi		# Parallel port interface device
#device		vpo		# Requires scbus and da


# PCI Ethernet NICs.
device		de		# DEC/Intel DC21x4x (``Tulip'')
device		txp		# 3Com 3cR990 (``Typhoon'')
device		vx		# 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these =
NICs!
device		miibus		# MII bus support
device		dc		# DEC/Intel 21143 and various workalikes
device		fxp		# Intel EtherExpress PRO/100B (82557, 82558)
device		pcn		# AMD Am79C97x PCI 10/100 NICs
device		rl		# RealTek 8129/8139
device		sf		# Adaptec AIC-6915 (``Starfire'')
device		sis		# Silicon Integrated Systems SiS 900/SiS 7016
device		ste		# Sundance ST201 (D-Link DFE-550TX)
device		tl		# Texas Instruments ThunderLAN
device		tx		# SMC EtherPower II (83c170 ``EPIC'')
device		vr		# VIA Rhine, Rhine II
device		wb		# Winbond W89C840F
device		wx		# Intel Gigabit Ethernet Card (``Wiseman'')
device		xl		# 3Com 3c90x (``Boomerang'', ``Cyclone'')
device		bge		# Broadcom BCM570x (``Tigon III'')

# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device		ed0	at isa? port 0x280 irq 10 iomem 0xd8000
device		ex
device		ep
device		fe0	at isa? port 0x300
# Xircom Ethernet
device		xe
# PRISM I IEEE 802.11b wireless NIC.
device		awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device		wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below =
will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device		an
# The probe order of these is presently determined by =
i386/isa/isa_compat.c.
device		ie0	at isa? port 0x300 irq 10 iomem 0xd0000
#device		le0	at isa? port 0x300 irq 5 iomem 0xd0000
device		lnc0	at isa? port 0x280 irq 10 drq 0
device		cs0	at isa? port 0x300
device		sn0	at isa? port 0x300 irq 10

# Pseudo devices - the number indicates how many units to allocate.
pseudo-device	loop		# Network loopback
pseudo-device	ether		# Ethernet support
#pseudo-device	sl	1	# Kernel SLIP
pseudo-device	ppp	2	# Kernel PPP
options		PPP_BSDCOMP
options		PPP_DEFLATE
options		PPP_FILTER
pseudo-device	tun	8	# Packet tunnel.
pseudo-device	pty		# Pseudo-ttys (telnet etc)
pseudo-device	md		# Memory "disks"
pseudo-device	gif		# IPv6 and IPv4 tunneling
pseudo-device	faith	1	# IPv6-to-IPv4 relaying (translation)

# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device	bpf		#Berkeley packet filter

# USB support
device		uhci		# UHCI PCI->USB interface
device		ohci		# OHCI PCI->USB interface
device		usb		# USB Bus (required)
device		ugen		# Generic
device		uhid		# "Human Interface Devices"
device		ukbd		# Keyboard
device		ulpt		# Printer
device		umass		# Disks/Mass storage - Requires scbus and da
device		ums		# Mouse
device		uscanner	# Scanners
device		urio		# Diamond Rio MP3 Player
# USB Ethernet, requires mii
device		aue		# ADMtek USB ethernet
device		cue		# CATC USB ethernet
device		kue		# Kawasaki LSI USB ethernet

options		USER_LDT
options		PERFMON
options		IPFIREWALL
options		IPFIREWALL_VERBOSE
options		IPFIREWALL_VERBOSE_LIMIT=3D10000
options		IPFIREWALL_FORWARD
options		IPFIREWALL_DEFAULT_TO_ACCEPT
options		IPDIVERT
#options		BRIDGE
options		IPFILTER
options		IPFILTER_LOG
options		IPSTEALTH
options		RANDOM_IP_ID
options		DUMMYNET
options		CLK_CALIBRATION_LOOP
options		NTIMECOUNTER=3D20
options		VESA
pseudo-device	splash
options		SC_PIXEL_MODE
options		SC_NO_SYSMOUSE
device          cy0     at isa? irq 10 iomem 0xd4000 iosiz 0x2000
options		IPSEC
options		IPSEC_ESP

------=_NextPart_000_00AA_01C40B42.129F66C0
Content-Type: text/plain;
	name="dmesg.txt"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="dmesg.txt"

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.9-RELEASE-p1 #6: Mon Jan 26 22:18:46 EET 2004
    root@ns.intfor.ro:/usr/obj/usr/src/sys/INTFOR
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel Pentium III (501.14-MHz 686-class CPU)
  Origin =3D "GenuineIntel"  Id =3D 0x681  Stepping =3D 1
  =
Features=3D0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,=
CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory  =3D 133103616 (129984K bytes)
config> di pcic0
config> di ppc0
config> di sn0
config> di lnc0
config> di ie0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory =3D 124284928 (121372K bytes)
Preloaded elf kernel "kernel" at 0xc052d000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc052d09c.
VESA: v2.0, 1024k memory, flags:0x1, mode table:0xc048ffa2 (1000022)
VESA: Intel810(TM) Graphics Chip Accelerated VGA BIOS
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 4 entries at 0xc00fdf30
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810 (i810 GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810 (i810 GMCH) SVGA controller> at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
rl0: <RealTek 8139 10/100BaseTX> port 0xc000-0xc0ff mem =
0xc0005000-0xc00050ff irq 11 at device 3.0 on pci1
rl0: Ethernet address: 00:02:44:5a:cf:6a
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl1: <RealTek 8139 10/100BaseTX> port 0xc400-0xc4ff mem =
0xc0006000-0xc00060ff irq 10 at device 4.0 on pci1
rl1: Ethernet address: 00:30:84:3b:0a:c7
miibus1: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus1
rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cy0: <Cyclades Cyclom-Y Serial Adapter> port 0xc800-0xc87f mem =
0xc0000000-0xc0003fff,0xc0004000-0xc000407f irq 12 at device 5.0 on pci1
cy0: driver is using old-style compatibility shims
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xf000-0xf00f at device 31.1 =
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on =
isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on =
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
DUMMYNET initialized (011031)
IP packet filtering initialized, divert enabled, rule-based forwarding =
enabled, default to accept, logging limited to 10000 packets/entry by =
default
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.31 initialized.  Default =3D pass all, Logging =3D =
enabled
ad0: 9787MB <QUANTUM FIREBALLlct10 10> [19885/16/63] at ata0-master =
UDMA66
Mounting root from ufs:/dev/ad0s1a
stray irq 7
stray irq 7
stray irq 7
stray irq 7
stray irq 7
too many stray irq 7's; not logging any more

------=_NextPart_000_00AA_01C40B42.129F66C0--



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040316082912.A1B1A43D2F>