Skip site navigation (1)Skip section navigation (2)
Date:      Sun, 4 Dec 2011 10:14:14 -0500
From:      "george vagner" <george@vagner.com>
To:        <freebsd-questions@freebsd.org>
Subject:   proper syntax for wifi
Message-ID:  <01b001ccb297$6487f7e0$2d97e7a0$@vagner.com>

next in thread | raw e-mail | index | archive | help

Ok I have a wireless interface ath0 and a wired re0 interface.

I would like to have hostapd running on the wireless interface and allow
access to the wired network also.

For the most part I have this working on most systems with one exception,
one of my clients cant connect
I am getting "deauthenticated due to local request" in my logs, and another
windows machine had the same issues until
I updated the wifi driver to the latest version which solved the problem on
the win machine.

Here is the error I am getting

wlan0: STA 00:09:2d:4b:21:a0 IEEE 802.11: associated
Dec  4 09:40:23 gateway hostapd: wlan0: STA 00:09:2d:4b:21:a0 IEEE 802.11:
deauthenticated due to local deauth request
Dec  4 09:40:23 gateway hostapd: wlan0: STA 00:09:2d:4b:21:a0 IEEE 802.11:
deassociated



I also don't know ifs right to assign an ip to a bridge or not, maybe
someone can look at this and make some suggestions
Cause I am all googled out or ideas.




> ifconfig -a
re0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu
1500
	
options=3899<RXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_UCAST,WOL_MCAST,
WOL_MAGIC>
	ether 90:fb:a6:ed:74:a6
	inet 192.168.0.3 netmask 0xffffff00 broadcast 192.168.0.255
	media: Ethernet autoselect (1000baseT <full-duplex>)
	status: active
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
	ether 00:c0:ca:1f:4a:d7
	media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
	status: running
plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> metric 0 mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	options=3<RXCSUM,TXCSUM>
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x9 
	inet6 ::1 prefixlen 128 
	inet 127.0.0.1 netmask 0xff000000 
	inet 127.0.0.254 netmask 0xffffffff 
	nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
1500
	ether 02:b5:34:b6:3f:00
	id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15
	maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200
	root id 00:00:00:00:00:00 priority 32768 ifcost 0 port 0
	member: wlan0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
	        ifmaxaddr 0 port 11 priority 128 path cost 370370
	member: re0 flags=143<LEARNING,DISCOVER,AUTOEDGE,AUTOPTP>
	        ifmaxaddr 0 port 1 priority 128 path cost 55
wlan0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0
mtu 1500
	ether 00:c0:ca:1f:4a:d7
	inet 192.168.0.2 netmask 0xffffff00 broadcast 192.168.0.255
	media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
	status: running
	ssid Gateway channel 11 (2462 MHz 11g) bssid 00:c0:ca:1f:4a:d7
	country US ecm authmode WPA privacy MIXED deftxkey 3 TKIP 2:128-bit
	TKIP 3:128-bit txpower 22.5 scanvalid 60 protmode CTS wme burst
	dtimperiod 1 -dfs


This is my rc.conf

> cat /etc/rc.conf
hostname="gateway.vagner.com"
defaultrouter="192.168.0.1"
gateway_enable="YES"
sshd_enable="YES"
wlans_ath0="wlan0"
create_args_wlan0="wlanmode hostap"
ifconfig_wlan0="inet 192.168.0.2 netmask 255.255.255.0 mode 11g channel 11"
hostapd_enable="YES"
ifconfig_re0="inet 192.168.0.3 netmask 255.255.255.0 up"
cloned_interfaces="bridge0"
ifconfig_bridge0="addm re0 addm wlan0"
routed_enable="YES"
webmin_enable="YES"
winbind_enable="YES"
dhcpd_enable="YES"                          # dhcpd enabled?
#dhcpd_flags="-q"                            # command option(s)
#dhcpd_conf="/usr/local/etc/dhcpd.conf"      # configuration file
dhcpd_ifaces="wlan0 re0"                     # ethernet interface(s)
#dhcpd_withumask="022"                       # file creation mask
inetd_enable="YES"
ntpdate_enable="NO"
ntpdate_enable="NO"
xntpd_program="/usr/local/bin/ntpd"
xntpd_flags="-A -g -N -c /etc/ntp.conf -p /var/run/ntpd.pid -l
/var/log/ntpd.log"
named_enable="YES"
cupsd_enable="YES"


and my /etc/hostapd.conf file

> cat /etc/hostapd.conf
##### hostapd configuration file
##############################################
# Empty lines and lines starting with # are ignored

# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for
# management frames); ath0 for madwifi
interface=wlan0

# In case of madwifi and nl80211 driver interfaces, an additional
configuration
# parameter, bridge, must be used to notify hostapd if the interface is
# included in a bridge. This parameter is not used with Host AP driver.
#bridge=br0

# Driver interface type
(hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that
does
# not control any wireless/wired driver.
# driver=hostap

# hostapd event logger configuration
#
# Two output method: syslog and stdout (only usable if not forking to
# background).
#
# Module bitfield (ORed bitfield of modules that will be logged; -1 = all
# modules):
# bit 0 (1) = IEEE 802.11
# bit 1 (2) = IEEE 802.1X
# bit 2 (4) = RADIUS
# bit 3 (8) = WPA
# bit 4 (16) = driver interface
# bit 5 (32) = IAPP
# bit 6 (64) = MLME
#
# Levels (minimum value for logged events):
#  0 = verbose debugging
#  1 = debugging
#  2 = informational messages
#  3 = notification
#  4 = warning
#
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2

# Dump file for state information (on SIGUSR1)
dump_file=/tmp/hostapd.dump

# Interface for separate control program. If this is specified, hostapd
# will create this directory and a UNIX domain socket for listening to
requests
# from external programs (CLI/GUI, etc.) for status information and
# configuration. The socket file will be named based on the interface name,
so
# multiple hostapd processes/interfaces can be run at the same time if more
# than one interface is used.
# /var/run/hostapd is the recommended directory for sockets and by default,
# hostapd_cli will use it when trying to connect with hostapd.
ctrl_interface=/var/run/hostapd

# Access control for the control interface can be configured by setting the
# directory to allow only members of a group to use sockets. This way, it is
# possible to run hostapd as root (since it needs to change network
# configuration and open raw sockets) and still allow GUI/CLI components to
be
# run as non-root users. However, since the control interface can be used to
# change the network configuration, this access needs to be protected in
many
# cases. By default, hostapd is configured to use gid 0 (root). If you
# want to allow non-root users to use the contron interface, add a new group
# and change this value to match with that group. Add users that should have
# control interface access to this group.
#
# This variable can be a group name or gid.
#ctrl_interface_group=wheel
ctrl_interface_group=0


##### IEEE 802.11 related configuration
#######################################

# SSID to be used in IEEE 802.11 management frames
ssid=Gateway

# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
# Set as needed to indicate country in which device is operating.
# This can limit available channels and transmit power.
country_code=US

# Enable IEEE 802.11d. This advertises the country_code and the set of
allowed
# channels and transmit power levels based on the regulatory limits. The
# country_code setting must be configured with the correct country for
# IEEE 802.11d functions.
# (default: 0 = disabled)
ieee80211d=1

# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g,
# Default: IEEE 802.11b
hw_mode=g

# Channel number (IEEE 802.11)
# (default: 0, i.e., not set)
# Please note that some drivers (e.g., madwifi) do not use this value from
# hostapd and the channel will need to be configuration separately with
# iwconfig.
channel=11

# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)
#beacon_int=100

# DTIM (delivery trafic information message) period (range 1..255):
# number of beacons between DTIMs (1 = every beacon includes DTIM element)
# (default: 2)
#dtim_period=2

# Maximum number of stations allowed in station table. New stations will be
# rejected after the station table is full. IEEE 802.11 has a limit of 2007
# different association IDs, so this number should not be larger than that.
# (default: 2007)
#max_num_sta=255

# RTS/CTS threshold; 2347 = disabled (default); range 0..2347
# If this field is not included in hostapd.conf, hostapd will not control
# RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it.
#rts_threshold=2347

# Fragmentation threshold; 2346 = disabled (default); range 256..2346
# If this field is not included in hostapd.conf, hostapd will not control
# fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set
# it.
#fragm_threshold=2346

# Rate configuration
# Default is to enable all rates supported by the hardware. This
configuration
# item allows this list be filtered so that only the listed rates will be
left
# in the list. If the list is empty, all rates are used. This list can have
# entries that are not in the list of rates the hardware supports (such
entries
# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps =
110.
# If this item is present, at least one rate have to be matching with the
rates
# hardware supports.
# default: use the most common supported rate setting for the selected
# hw_mode (i.e., this line can be removed from configuration file in most
# cases)
#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540

# Basic rate set configuration
# List of rates (in 100 kbps) that are included in the basic rate set.
# If this item is not included, usually reasonable default set is used.
#basic_rates=10 20
#basic_rates=10 20 55 110
#basic_rates=60 120 240

# Short Preamble
# This parameter can be used to enable optional use of short preamble for
# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network
performance.
# This applies only to IEEE 802.11b-compatible networks and this should only
be
# enabled if the local hardware supports use of short preamble. If any of
the
# associated STAs do not support short preamble, use of short preamble will
be
# disabled (and enabled when such STAs disassociate) dynamically.
# 0 = do not allow use of short preamble (default)
# 1 = allow use of short preamble
#preamble=1

# Station MAC address -based authentication
# Please note that this kind of access control requires a driver that uses
# hostapd to take care of management frame processing and as such, this can
be
# used with driver=hostap or driver=nl80211, but not with driver=madwifi.
# 0 = accept unless in deny list
# 1 = deny unless in accept list
# 2 = use external RADIUS server (accept/deny lists are searched first)
macaddr_acl=0

# Accept/deny lists are read from separate files (containing list of
# MAC addresses, one per line). Use absolute path name to make sure that the
# files can be read on SIGHUP configuration reloads.
#accept_mac_file=/etc/hostapd.accept
#deny_mac_file=/etc/hostapd.deny

# IEEE 802.11 specifies two authentication algorithms. hostapd can be
# configured to allow both of these or only one. Open system authentication
# should be used with IEEE 802.1X.
# Bit fields of allowed authentication algorithms:
# bit 0 = Open System Authentication
# bit 1 = Shared Key Authentication (requires WEP)
auth_algs=1

# Send empty SSID in beacons and ignore probe request frames that do not
# specify full SSID, i.e., require stations to know SSID.
# default: disabled (0)
# 1 = send empty (length=0) SSID in beacon and ignore probe request for
#     broadcast SSID
# 2 = clear SSID (ASCII 0), but keep the original length (this may be
required
#     with some clients that do not support empty SSID) and ignore probe
#     requests for broadcast SSID
ignore_broadcast_ssid=0

# TX queue parameters (EDCF / bursting)
# default for all these fields: not set, use hardware defaults
# tx_queue_<queue name>_<param>
# queues: data0, data1, data2, data3, after_beacon, beacon
#		(data0 is the highest priority queue)
# parameters:
#   aifs: AIFS (default 2)
#   cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023)
#   cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin
#   burst: maximum length (in milliseconds with precision of up to 0.1 ms)
for
#          bursting
#
# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):
# These parameters are used by the access point when transmitting frames
# to the clients.
#
# Low priority / AC_BK = background
#tx_queue_data3_aifs=7
#tx_queue_data3_cwmin=15
#tx_queue_data3_cwmax=1023
#tx_queue_data3_burst=0
# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0
#
# Normal priority / AC_BE = best effort
#tx_queue_data2_aifs=3
#tx_queue_data2_cwmin=15
#tx_queue_data2_cwmax=63
#tx_queue_data2_burst=0
# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0
#
# High priority / AC_VI = video
#tx_queue_data1_aifs=1
#tx_queue_data1_cwmin=7
#tx_queue_data1_cwmax=15
#tx_queue_data1_burst=3.0
# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0
#
# Highest priority / AC_VO = voice
#tx_queue_data0_aifs=1
#tx_queue_data0_cwmin=3
#tx_queue_data0_cwmax=7
#tx_queue_data0_burst=1.5
# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3
#
# Special queues; normally not user configurable
#
#tx_queue_after_beacon_aifs=2
#tx_queue_after_beacon_cwmin=15
#tx_queue_after_beacon_cwmax=1023
#tx_queue_after_beacon_burst=0
#
#tx_queue_beacon_aifs=2
#tx_queue_beacon_cwmin=3
#tx_queue_beacon_cwmax=7
#tx_queue_beacon_burst=1.5

# 802.1D Tag to AC mappings
# WMM specifies following mapping of data frames to different ACs. This
mapping
# can be configured using Linux QoS/tc and sch_pktpri.o module.
# 802.1D Tag	802.1D Designation	Access Category	WMM Designation
# 1		BK			AC_BK		Background
# 2		-			AC_BK		Background
# 0		BE			AC_BE		Best Effort
# 3		EE			AC_VI		Video
# 4		CL			AC_VI		Video
# 5		VI			AC_VI		Video
# 6		VO			AC_VO		Voice
# 7		NC			AC_VO		Voice
# Data frames with no priority information: AC_BE
# Management frames: AC_VO
# PS-Poll frames: AC_BE

# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e):
# for 802.11a or 802.11g networks
# These parameters are sent to WMM clients when they associate.
# The parameters will be used by WMM clients for frames transmitted to the
# access point.
#
# note - txop_limit is in units of 32microseconds
# note - acm is admission control mandatory flag. 0 = admission control not
# required, 1 = mandatory
# note - here cwMin and cmMax are in exponent form. the actual cw value used
# will be (2^n)-1 where n is the value given here
#
#wme_enabled=1
#
# Low priority / AC_BK = background
wme_ac_bk_cwmin=4
wme_ac_bk_cwmax=10
wme_ac_bk_aifs=7
wme_ac_bk_txop_limit=0
wme_ac_bk_acm=0
# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10
#
# Normal priority / AC_BE = best effort
wme_ac_be_aifs=3
wme_ac_be_cwmin=4
wme_ac_be_cwmax=10
wme_ac_be_txop_limit=0
wme_ac_be_acm=0
# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7
#
# High priority / AC_VI = video
wme_ac_vi_aifs=2
wme_ac_vi_cwmin=3
wme_ac_vi_cwmax=4
wme_ac_vi_txop_limit=94
wme_ac_vi_acm=0
# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188
#
# Highest priority / AC_VO = voice
wme_ac_vo_aifs=2
wme_ac_vo_cwmin=2
wme_ac_vo_cwmax=3
wme_ac_vo_txop_limit=47
wme_ac_vo_acm=0
# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102

# Static WEP key configuration
#
# The key number to use when transmitting.
# It must be between 0 and 3, and the corresponding key must be set.
# default: not set
#wep_default_key=0
# The WEP keys to use.
# A key may be a quoted string or unquoted hexadecimal digits.
# The key length should be 5, 13, or 16 characters, or 10, 26, or 32
# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or
# 128-bit (152-bit) WEP is used.
# Only the default key must be supplied; the others are optional.
# default: not set
#wep_key0=123456789a
#wep_key1="vwxyz"
#wep_key2=0102030405060708090a0b0c0d
#wep_key3=".2.4.6.8.0.23"

# Station inactivity limit
#
# If a station does not send anything in ap_max_inactivity seconds, an
# empty data frame is sent to it in order to verify whether it is
# still in range. If this frame is not ACKed, the station will be
# disassociated and then deauthenticated. This feature is used to
# clear station table of old entries when the STAs move out of the
# range.
#
# The station can associate again with the AP if it is still in range;
# this inactivity poll is just used as a nicer way of verifying
# inactivity; i.e., client will not report broken connection because
# disassociation frame is not sent immediately without first polling
# the STA with a data frame.
# default: 300 (i.e., 5 minutes)
#ap_max_inactivity=300

# Enable/disable internal bridge for packets between associated stations.
#
# When IEEE 802.11 is used in managed mode, packets are usually send through
# the AP even if they are from a wireless station to another wireless
station.
# This functionality requires that the AP has a bridge functionality that
sends
# frames back to the same interface if their destination is another
associated
# station. In addition, broadcast/multicast frames from wireless stations
will
# be sent both to the host system net stack (e.g., to eventually wired
network)
# and back to the wireless interface.
#
# The internal bridge is implemented within the wireless kernel module and
it
# bypasses kernel filtering (netfilter/iptables/ebtables). If direct
# communication between the stations needs to be prevented, the internal
# bridge can be disabled by setting bridge_packets=0.
#
# Note: If this variable is not included in hostapd.conf, hostapd does not
# change the configuration and iwpriv can be used to set the value with
# 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
# hostapd will override possible iwpriv configuration whenever configuration
# file is reloaded.
#
# default: do not control from hostapd (80211.o defaults to 1=enabled)
#bridge_packets=1

# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed
to
# remain asleep). Default: 65535 (no limit apart from field size)
#max_listen_interval=100

##### IEEE 802.11n related configuration
######################################

# ieee80211n: Whether IEEE 802.11n (HT) is enabled
# 0 = disabled (default)
# 1 = enabled
#ieee80211n=1

# ht_capab: HT capabilities (list of flags)
# LDPC coding capability: [LDPC] = supported
# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with
secondary
#	channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz
#	with secondary channel below the primary channel
#	(20 MHz only if neither is set)
#	Note: There are limits on which channels can be used with HT40- and
#	HT40+. Following table shows the channels that may be available for
#	HT40- and HT40+ use per IEEE 802.11n Annex J:
#	freq		HT40-		HT40+
#	2.4 GHz		5-13		1-7 (1-9 in Europe/Japan)
#	5 GHz		40,48,56,64	36,44,52,60
#	(depending on the location, not all of these channels may be
available
#	for use)
# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]
#	(SMPS disabled if neither is set)
# HT-greenfield: [GF] (disabled if not set)
# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)
# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)
# Tx STBC: [TX-STBC] (disabled if not set)
# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial
#	streams), or [RX-STBC123] (one, two, or three spatial streams); Rx
STBC
#	disabled if none of these set
# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set)
# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if
not
#	set)
# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set)
# PSMP support: [PSMP] (disabled if not set)
# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)
#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]

##### IEEE 802.1X-2004 related configuration
##################################

# Require IEEE 802.1X authorization
#ieee8021x=1

# IEEE 802.1X/EAPOL version
# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL
# version 2. However, there are many client implementations that do not
handle
# the new version number correctly (they seem to drop the frames
completely).
# In order to make hostapd interoperate with these clients, the version
number
# can be set to the older version (1) with this configuration value.
eapol_version=2

# Optional displayable message sent with EAP Request-Identity. The first \0
# in this string will be converted to ASCII-0 (nul). This can be used to
# separate network info (comma separated list of attribute=value pairs);
see,
# e.g., RFC 4284.
#eap_message=hello
#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com

# WEP rekeying (disabled if key lengths are not set or are set to 0)
# Key lengths for default/broadcast and individual/unicast keys:
# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits)
# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits)
#wep_key_len_broadcast=5
#wep_key_len_unicast=5
# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once)
#wep_rekey_period=300

# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if
# only broadcast keys are used)
#eapol_key_index_workaround=0

# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable
# reauthentication).
#eap_reauth_period=3600

# Use PAE group address (01:80:c2:00:00:03) instead of individual target
# address when sending EAPOL frames with driver=wired. This is the most
common
# mechanism used in wired authentication, but it also requires that the port
# is only used by one station.
#use_pae_group_addr=1

##### Integrated EAP server
###################################################

# Optionally, hostapd can be configured to use an integrated EAP server
# to process EAP authentication locally without need for an external RADIUS
# server. This functionality can be used both as a local authentication
server
# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices.

# Use integrated EAP server instead of external RADIUS authentication
# server. This is also needed if hostapd is configured to act as a RADIUS
# authentication server.
#eap_server=0

# Path for EAP server user database
#eap_user_file=/etc/hostapd.eap_user

# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
#ca_cert=/etc/hostapd.ca.pem

# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
#server_cert=/etc/hostapd.server.pem

# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS
# This may point to the same file as server_cert if both certificate and key
# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be
# used by commenting out server_cert and specifying the PFX file as the
# private_key.
#private_key=/etc/hostapd.server.prv

# Passphrase for private key
#private_key_passwd=secret passphrase

# Enable CRL verification.
# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a
# valid CRL signed by the CA is required to be included in the ca_cert file.
# This can be done by using PEM format for CA certificate and CRL and
# concatenating these into one file. Whenever CRL changes, hostapd needs to
be
# restarted to take the new CRL into use.
# 0 = do not verify CRLs (default)
# 1 = check the CRL of the user certificate
# 2 = check all CRLs in the certificate path
#check_crl=1

# dh_file: File path to DH/DSA parameters file (in PEM format)
# This is an optional configuration file for setting parameters for an
# ephemeral DH key exchange. In most cases, the default RSA authentication
does
# not use this configuration. However, it is possible setup RSA to use
# ephemeral DH key exchange. In addition, ciphers with DSA keys always use
# ephemeral DH keys. This can be used to achieve forward secrecy. If the
file
# is in DSA parameters format, it will be automatically converted into DH
# params. This parameter is required if anonymous EAP-FAST is used.
# You can generate DH parameters file with OpenSSL, e.g.,
# "openssl dhparam -out /etc/hostapd.dh.pem 1024"
#dh_file=/etc/hostapd.dh.pem

# Configuration data for EAP-SIM database/authentication gateway interface.
# This is a text string in implementation specific format. The example
# implementation in eap_sim_db.c uses this as the UNIX domain socket name
for
# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses
"unix:"
# prefix.
#eap_sim_db=unix:/tmp/hlr_auc_gw.sock

# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret,
# random value. It is configured as a 16-octet value in hex format. It can
be
# generated, e.g., with the following command:
# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' '
#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f

# EAP-FAST authority identity (A-ID)
# A-ID indicates the identity of the authority that issues PACs. The A-ID
# should be unique across all issuing servers. In theory, this is a variable
# length field, but due to some existing implementations required A-ID to be
# 16 octets in length, it is strongly recommended to use that length for the
# field to provided interoperability with deployed peer implementation. This
# field is configured in hex format.
#eap_fast_a_id=101112131415161718191a1b1c1d1e1f

# EAP-FAST authority identifier information (A-ID-Info)
# This is a user-friendly name for the A-ID. For example, the enterprise
name
# and server name in a human-readable format. This field is encoded as
UTF-8.
#eap_fast_a_id_info=test server

# Enable/disable different EAP-FAST provisioning modes:
#0 = provisioning disabled
#1 = only anonymous provisioning allowed
#2 = only authenticated provisioning allowed
#3 = both provisioning modes allowed (default)
#eap_fast_prov=3

# EAP-FAST PAC-Key lifetime in seconds (hard limit)
#pac_key_lifetime=604800

# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard
# limit). The server will generate a new PAC-Key when this number of seconds
# (or fewer) of the lifetime remains.
#pac_key_refresh_time=86400

# EAP-SIM and EAP-AKA protected success/failure indication using
AT_RESULT_IND
# (default: 0 = disabled).
#eap_sim_aka_result_ind=1

# Trusted Network Connect (TNC)
# If enabled, TNC validation will be required before the peer is allowed to
# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other
# EAP method is enabled, the peer will be allowed to connect without TNC.
#tnc=1


##### IEEE 802.11f - Inter-Access Point Protocol (IAPP)
#######################

# Interface to be used for IAPP broadcast packets
#iapp_interface=eth0


##### RADIUS client configuration
#############################################
# for IEEE 802.1X with external Authentication Server, IEEE 802.11
# authentication with external ACL for MAC addresses, and accounting

# The own IP address of the access point (used as NAS-IP-Address)
own_ip_addr=127.0.0.1

# Optional NAS-Identifier string for RADIUS messages. When used, this should
be
# a unique to the NAS within the scope of the RADIUS server. For example, a
# fully qualified domain name can be used here.
# When using IEEE 802.11r, nas_identifier must be set and must be between 1
and
# 48 octets long.
#nas_identifier=ap.example.com

# RADIUS authentication server
#auth_server_addr=127.0.0.1
#auth_server_port=1812
#auth_server_shared_secret=secret

# RADIUS accounting server
#acct_server_addr=127.0.0.1
#acct_server_port=1813
#acct_server_shared_secret=secret

# Secondary RADIUS servers; to be used if primary one does not reply to
# RADIUS packets. These are optional and there can be more than one
secondary
# server listed.
#auth_server_addr=127.0.0.2
#auth_server_port=1812
#auth_server_shared_secret=secret2
#
#acct_server_addr=127.0.0.2
#acct_server_port=1813
#acct_server_shared_secret=secret2

# Retry interval for trying to return to the primary RADIUS server (in
# seconds). RADIUS client code will automatically try to use the next server
# when the current server is not replying to requests. If this interval is
set,
# primary server will be retried after configured amount of time even if the
# currently used secondary server is still working.
#radius_retry_primary_interval=600


# Interim accounting update interval
# If this is set (larger than 0) and acct_server is configured, hostapd will
# send interim accounting updates every N seconds. Note: if set, this
overrides
# possible Acct-Interim-Interval attribute in Access-Accept message. Thus,
this
# value should not be configured in hostapd.conf, if RADIUS server is used
to
# control the interim interval.
# This value should not be less 600 (10 minutes) and must not be less than
# 60 (1 minute).
#radius_acct_interim_interval=600

# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN
# is used for the stations. This information is parsed from following RADIUS
# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN),
# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value
# VLANID as a string). vlan_file option below must be configured if dynamic
# VLANs are used. Optionally, the local MAC ACL list (accept_mac_file) can
be
# used to set static client MAC address to VLAN ID mapping.
# 0 = disabled (default)
# 1 = option; use default interface if RADIUS server does not include VLAN
ID
# 2 = required; reject authentication if RADIUS server does not include VLAN
ID
#dynamic_vlan=0

# VLAN interface list for dynamic VLAN mode is read from a separate text
file.
# This list is used to map VLAN ID from the RADIUS server to a network
# interface. Each station is bound to one interface in the same way as with
# multiple BSSIDs or SSIDs. Each line in this text file is defining a new
# interface and the line must include VLAN ID and interface name separated
by
# white space (space or tab).
#vlan_file=/etc/hostapd.vlan

# Interface where 802.1q tagged packets should appear when a RADIUS server
is
# used to determine which VLAN a station is on.  hostapd creates a bridge
for
# each VLAN.  Then hostapd adds a VLAN interface (associated with the
interface
# indicated by 'vlan_tagged_interface') and the appropriate wireless
interface
# to the bridge.
#vlan_tagged_interface=eth0


##### RADIUS authentication server configuration
##############################

# hostapd can be used as a RADIUS authentication server for other hosts.
This
# requires that the integrated EAP server is also enabled and both
# authentication services are sharing the same configuration.

# File name of the RADIUS clients configuration for the RADIUS server. If
this
# commented out, RADIUS server is disabled.
#radius_server_clients=/etc/hostapd.radius_clients

# The UDP port number for the RADIUS authentication server
#radius_server_auth_port=1812

# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API)
#radius_server_ipv6=1


##### WPA/IEEE 802.11i configuration
##########################################

# Enable WPA. Setting this variable configures the AP to require WPA (either
# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK,
either
# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include
WPA-PSK.
# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
# RADIUS authentication server must be configured, and WPA-EAP must be
included
# in wpa_key_mgmt.
# This field is a bit field that can be used to enable WPA (IEEE
802.11i/D3.0)
# and/or WPA2 (full IEEE 802.11i/RSN):
# bit0 = WPA
# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
wpa=1

# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit
# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase
# (8..63 characters) that will be converted to PSK. This conversion uses
SSID
# so the PSK changes when ASCII passphrase is used and the SSID is changed.
# wpa_psk (dot11RSNAConfigPSKValue)
# wpa_passphrase (dot11RSNAConfigPSKPassPhrase)
#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
wpa_passphrase=wireless_password

# Optionally, WPA PSKs can be read from a separate text file (containing
list
# of (PSK,MAC address) pairs. This allows more than one PSK to be
configured.
# Use absolute path name to make sure that the files can be read on SIGHUP
# configuration reloads.
#wpa_psk_file=/etc/hostapd.wpa_psk

# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can
be
# added to enable SHA256-based stronger algorithms.
# (dot11RSNAConfigAuthenticationSuitesTable)
wpa_key_mgmt=WPA-PSK WPA-EAP

# Set of accepted cipher suites (encryption algorithms) for pairwise keys
# (unicast packets). This is a space separated list of algorithms:
# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]
# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]
# Group cipher suite (encryption algorithm for broadcast and multicast
frames)
# is automatically selected based on this configuration. If only CCMP is
# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise,
# TKIP will be used as the group cipher.
# (dot11RSNAConfigPairwiseCiphersTable)
# Pairwise cipher for WPA (v1) (default: TKIP)
#wpa_pairwise=TKIP CCMP
# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value)
#rsn_pairwise=CCMP

# Time interval for rekeying GTK (broadcast/multicast encryption keys) in
# seconds. (dot11RSNAConfigGroupRekeyTime)
#wpa_group_rekey=600

# Rekey GTK when any STA that possesses the current GTK is leaving the BSS.
# (dot11RSNAConfigGroupRekeyStrict)
#wpa_strict_rekey=1

# Time interval for rekeying GMK (master key used internally to generate
GTKs
# (in seconds).
#wpa_gmk_rekey=86400

# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying
of
# PTK to mitigate some attacks against TKIP deficiencies.
#wpa_ptk_rekey=600

# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up
# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN
# authentication and key handshake before actually associating with a new
AP.
# (dot11RSNAPreauthenticationEnabled)
#rsn_preauth=1
#
# Space separated list of interfaces from which pre-authentication frames
are
# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all
# interface that are used for connections to other APs. This could include
# wired interfaces and WDS links. The normal wireless data interface towards
# associated stations (e.g., wlan0) should not be added, since
# pre-authentication is only used with APs other than the currently
associated
# one.
#rsn_preauth_interfaces=eth0

# peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is
# allowed. This is only used with RSN/WPA2.
# 0 = disabled (default)
# 1 = enabled
#peerkey=1

# ieee80211w: Whether management frame protection (MFP) is enabled
# 0 = disabled (default)
# 1 = optional
# 2 = required
#ieee80211w=0

# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)
# (maximum time to wait for a SA Query response)
# dot11AssociationSAQueryMaximumTimeout, 1...4294967295
#assoc_sa_query_max_timeout=1000

# Association SA Query retry timeout (in TU = 1.024 ms; for MFP)
# (time between two subsequent SA Query requests)
# dot11AssociationSAQueryRetryTimeout, 1...4294967295
#assoc_sa_query_retry_timeout=201


# okc: Opportunistic Key Caching (aka Proactive Key Caching)
# Allow PMK cache to be shared opportunistically among configured interfaces
# and BSSes (i.e., all configurations within a single hostapd process).
# 0 = disabled (default)
# 1 = enabled
#okc=1


##### IEEE 802.11r configuration
##############################################

# Mobility Domain identifier (dot11FTMobilityDomainID, MDID)
# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the
# same SSID) between which a STA can use Fast BSS Transition.
# 2-octet identifier as a hex string.
#mobility_domain=a1b2

# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID)
# 1 to 48 octet identifier.
# This is configured with nas_identifier (see RADIUS client section above).

# Default lifetime of the PMK-RO in minutes; range 1..65535
# (dot11FTR0KeyLifetime)
#r0_key_lifetime=10000

# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID)
# 6-octet identifier as a hex string.
#r1_key_holder=000102030405

# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535)
# (dot11FTReassociationDeadline)
#reassociation_deadline=1000

# List of R0KHs in the same Mobility Domain
# format: <MAC address> <NAS Identifier> <128-bit key as hex string>
# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC
# address when requesting PMK-R1 key from the R0KH that the STA used during
the
# Initial Mobility Domain Association.
#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f
#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff
# And so on.. One line per R0KH.

# List of R1KHs in the same Mobility Domain
# format: <MAC address> <R0KH-ID> <128-bit key as hex string>
# This list is used to map R1KH-ID to a destination MAC address when sending
# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the
MD
# that can request PMK-R1 keys.
#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f
#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff
# And so on.. One line per R1KH.

# Whether PMK-R1 push is enabled at R0KH
# 0 = do not push PMK-R1 to all configured R1KHs (default)
# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived
#pmk_r1_push=1

##### Passive scanning
########################################################
# Scan different channels every N seconds. 0 = disable passive scanning.
#passive_scan_interval=60

# Listen N usecs on each channel when doing passive scanning.
# This value plus the time needed for changing channels should be less than
# 32 milliseconds (i.e. 32000 usec) to avoid interruptions to normal
# operations. Time needed for channel changing varies based on the used wlan
# hardware.
# default: disabled (0)
#passive_scan_listen=10000

# Passive scanning mode:
# 0 = scan all supported modes (802.11a/b/g/Turbo) (default)
# 1 = scan only the mode that is currently used for normal operations
#passive_scan_mode=1

# Maximum number of entries kept in AP table (either for passive scanning or
# for detecting Overlapping Legacy BSS Condition). The oldest entry will be
# removed when adding a new entry that would make the list grow over this
# limit. Note! Wi-Fi certification for IEEE 802.11g requires that OLBC is
# enabled, so this field should not be set to 0 when using IEEE 802.11g.
# default: 255
#ap_table_max_size=255

# Number of seconds of no frames received after which entries may be deleted
# from the AP table. Since passive scanning is not usually performed
frequently
# this should not be set to very small value. In addition, there is no
# guarantee that every scan cycle will receive beacon frames from the
# neighboring APs.
# default: 60
#ap_table_expiration_time=3600


##### Wi-Fi Protected Setup (WPS)
#############################################

# WPS state
# 0 = WPS disabled (default)
# 1 = WPS enabled, not configured
# 2 = WPS enabled, configured
#wps_state=2

# AP can be configured into a locked state where new WPS Registrar are not
# accepted, but previously authorized Registrars (including the internal
one)
# can continue to add new Enrollees.
#ap_setup_locked=1

# Universally Unique IDentifier (UUID; see RFC 4122) of the device
# This value is used as the UUID for the internal WPS Registrar. If the AP
# is also using UPnP, this value should be set to the device's UPnP UUID.
# If not configured, UUID will be generated based on the local MAC address.
#uuid=12345678-9abc-def0-1234-56789abcdef0

# Note: If wpa_psk_file is set, WPS is used to generate random, per-device
PSKs
# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the
# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use
of
# per-device PSKs is recommended as the more secure option (i.e., make sure
to
# set wpa_psk_file when using WPS with WPA-PSK).

# When an Enrollee requests access to the network with PIN method, the
Enrollee
# PIN will need to be entered for the Registrar. PIN request notifications
are
# sent to hostapd ctrl_iface monitor. In addition, they can be written to a
# text file that could be used, e.g., to populate the AP administration UI
with
# pending PIN requests. If the following variable is set, the PIN requests
will
# be written to the configured file.
#wps_pin_requests=/var/run/hostapd_wps_pin_requests

# Device Name
# User-friendly description of device; up to 32 octets encoded in UTF-8
#device_name=Wireless AP

# Manufacturer
# The manufacturer of the device (up to 64 ASCII characters)
#manufacturer=Company

# Model Name
# Model of the device (up to 32 ASCII characters)
#model_name=WAP

# Model Number
# Additional device description (up to 32 ASCII characters)
#model_number=123

# Serial Number
# Serial number of the device (up to 32 characters)
#serial_number=12345

# Primary Device Type
# Used format: <categ>-<OUI>-<subcateg>
# categ = Category as an integer value
# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for
#       default WPS OUI
# subcateg = OUI-specific Sub Category as an integer value
# Examples:
#   1-0050F204-1 (Computer / PC)
#   1-0050F204-2 (Computer / Server)
#   5-0050F204-1 (Storage / NAS)
#   6-0050F204-1 (Network Infrastructure / AP)
#device_type=6-0050F204-1

# OS Version
# 4-octet operating system version number (hex string)
#os_version=01020300

# Config Methods
# List of the supported configuration methods
#config_methods=label display push_button keypad

# Access point PIN for initial configuration and adding Registrars
# If not set, hostapd will not allow external WPS Registrars to control the
# access point.
#ap_pin=12345670

# Skip building of automatic WPS credential
# This can be used to allow the automatically generated Credential attribute
to
# be replaced with pre-configured Credential(s).
#skip_cred_build=1

# Additional Credential attribute(s)
# This option can be used to add pre-configured Credential attributes into
M8
# message when acting as a Registrar. If skip_cred_build=1, this data will
also
# be able to override the Credential attribute that would have otherwise
been
# automatically generated based on network configuration. This configuration
# option points to an external file that much contain the WPS Credential
# attribute(s) as binary data.
#extra_cred=hostapd.cred

# Credential processing
#   0 = process received credentials internally (default)
#   1 = do not process received credentials; just pass them over ctrl_iface
to
#	external program(s)
#   2 = process received credentials internally and pass them over
ctrl_iface
#	to external program(s)
# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and
# extra_cred be used to provide the Credential data for Enrollees.
#
# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file
# both for Credential processing and for marking AP Setup Locked based on
# validation failures of AP PIN. An external program is responsible on
updating
# the configuration appropriately in this case.
#wps_cred_processing=0

# AP Settings Attributes for M7
# By default, hostapd generates the AP Settings Attributes for M7 based on
the
# current configuration. It is possible to override this by providing a file
# with pre-configured attributes. This is similar to extra_cred file format,
# but the AP Settings attributes are not encapsulated in a Credential
# attribute.
#ap_settings=hostapd.ap_settings

# WPS UPnP interface
# If set, support for external Registrars is enabled.
#upnp_iface=br0

# Friendly Name (required for UPnP)
# Short description for end use. Should be less than 64 characters.
#friendly_name=WPS Access Point

# Manufacturer URL (optional for UPnP)
#manufacturer_url=http://www.example.com/

# Model Description (recommended for UPnP)
# Long description for end user. Should be less than 128 characters.
#model_description=Wireless Access Point

# Model URL (optional for UPnP)
#model_url=http://www.example.com/model/

# Universal Product Code (optional for UPnP)
# 12-digit, all-numeric code that identifies the consumer package.
#upc=123456789012

##### Multiple BSSID support
##################################################
#
# Above configuration is using the default interface (wlan#, or multi-SSID
VLAN
# interfaces). Other BSSIDs can be added by using separator 'bss' with
# default interface name to be allocated for the data packets of the new
BSS.
#
# hostapd will generate BSSID mask based on the BSSIDs that are
# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this
is
# not the case, the MAC address of the radio must be changed before starting
# hostapd (ifconfig wlan0 hw ether <MAC addr>).
#
# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is
# specified using the 'bssid' parameter.
# If an explicit BSSID is specified, it must be chosen such that it:
# - results in a valid MASK that covers it and the dev_addr
# - is not the same as the MAC address of the radio
# - is not the same as any other explicitly specified BSSID
#
# Please note that hostapd uses some of the values configured for the first
BSS
# as the defaults for the following BSSes. However, it is recommended that
all
# BSSes include explicit configuration of all relevant configuration items.
#
#bss=wlan0_0
#ssid=test2
# most of the above items can be used here (apart from radio interface
specific
# items, like channel)

#bss=wlan0_1
#bssid=00:13:10:95:fe:0b
# ...

Enter a shell command to execute in the text field below. The cd command may
be used to change directory for subsequent commands.
		
		





Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?01b001ccb297$6487f7e0$2d97e7a0$>