Date: Sat, 20 Jul 2002 11:15:20 +1000 From: "bigMAX" <bigmax@newmail.net> To: <freebsd-hardware@freebsd.org> Subject: Re: USB: "ugen0: device problem" Message-ID: <014601c22f8a$ea9aa1b0$0101a8c0@BIGMAX> References: <013401c22f0a$a472f190$0101a8c0@BIGMAX> <20020719115837.GA5689@ftp.crustpunk.org>
next in thread | previous in thread | raw e-mail | index | archive | help
Thanks Craig! That was it!
----- Original Message -----
From: "Craig Dooley" <cd5697@albany.edu>
To: <freebsd-hardware@FreeBSD.ORG>
Sent: Friday, July 19, 2002 9:58 PM
Subject: Re: USB: "ugen0: device problem"
> I dont know if this will help, but when I was trying to use FreeBSD on
> an Abit VP6 Motherboard, I was having problems also. The solution I
> found was to go into the bios and change the MPS from 1.4 down to 1.1
> and it worked fine. I was having a similar problem that whenever I
> plugged in a new device, it would disconnect it immediately. Im not
> sure where it's documented and where I found that, but sometion to look
> into.
>
> -Craig
>
> On Fri, Jul 19, 2002 at 07:57:02PM +1000, bigMAX wrote:
> > My apologies if this posting is off-topic, but i'm thinking it might be
a
> > problem with some gigabyte motherboards and I'd be interested if anyone
> > could confirm that it either was or wasn't.
> >
> >
> > Hi,
> >
> > I've been trying to get an alcatel speedtouch usb modem working and
after
> > spending all afternoon struggling with it I've concluded that I don't
have
> > USB working at all :(
> > I also have a xerox docuprint p8ex printer which I am using to test
whether
> > usb is working - although I'm not concerned with making this print.
> >
> > Here are my details:
> > I'm running FreeBSD 4.6-STABLE, I've got a dual P2-350 with a Gigabyte
> > GA6BXD motherboard.
> > The onboard USB ports are identified as "Intel 82371AB/EB (PIIX4) USB
> > controller".
> > I've updated the motherboard's bios to the latest version (F4b).
> > I removed a network card that was sharing an irq with the usb device so
> > their are definitely no irq conflicts.
> > A complete dmesg output is included at the end of the message along with
the
> > output from usbd -dvvv
> >
> > If I boot the machine with the usb devices attached they are recognised:
> > ugen0: ALCATEL Speed Touch USB , rev 1.10/0.00, addr 2
> > ugen1: Lexmark International, Inc. Color Jetprinter 5500\^H?\^H, rev
> > 1.00/0.63, addr 3
> >
> > But any attempt to use the adsl modem will cause the following error:
> > grody# modem_run -f /usr/local/libdata/mgmt.o -m -d /dev/ugen0 -v 2
> > Gotcha, I found your ADSL ALCATEL SpeedTouch USB modem!
> > (The modem lights will then start flashing for a while, then go red,
then
> > switch off)
> > ugen0: at uhub0 port 1 (addr 2) disconnected
> > ugen0: detached
> > BLOCK1: Input/output error
> > Uploading /usr/local/libdata/mgmt.o failed! Continuing anyway ...
> > pusb_set_configuration 1: Inappropriate ioctl for device
> >
> > I originally thought it was just problems getting the alcatel driver
going
> > but the following happens when I try to plug either the printer or adsl
> > modem into the machine while it is already running:
> > uhub0: device problem, disabling port 1
> >
> > Does anyone have any ideas? I'm completely lost. I thought being a
regular
> > (and a bit old) intel chipset the usb would be pretty generic. After a
_lot_
> > of searching through google and ml archives i'm thinking it might be a
> > problem with gigabyte boards - I saw a lot of (unanswered) messages with
> > similar problems from people with gigabyte boards.
> >
> > Thanks
> >
> > Jason.
> >
> >
> >
> > The following is the output from running usbd -dvvv:
> > grody# /usr/sbin/usbd -dvvv
> > usbd: opened /dev/usb0
> > usbd: reading configuration file /etc/usbd.conf
> > usbd: action 1: ActiveWire board, firmware download
> > vndr=0x0854 prdct=0x0100 rlse=0x0000
> > attach='/usr/local/bin/ezdownload -f
> > /usr/local/share/usb/firmware/0854.0100.0_01.hex ${DEVNAME}'
> > usbd: action 2: Entrega Serial with UART
> > vndr=0x1645 prdct=0x8001 rlse=0x0101
> > attach='/usr/sbin/ezdownload -v -f
/usr/share/usb/firmware/1645.8001.0101
> > /dev/${DEVNAME}'
> > usbd: action 3: USB ethernet
> > devname: [ack]ue[0-9]+
> > attach='dhclient ${DEVNAME}'
> > detach='killall dhclient'
> > usbd: action 4: Mouse
> > devname: ums[0-9]+
> > attach='/usr/sbin/moused -p /dev/${DEVNAME} -I
> > /var/run/moused.${DEVNAME}.pid'
> > usbd: action 5: USB device
> > usbd: 5 actions
> > usbd: opened /dev/usb
> > usbd: detach event at 1027071605.407825000, product 0x3201, vendor
0x0419:
> > vndr=0x0419 prdct=0x3201 rlse=0x0063 clss=0x0000 subclss=0x0000
> > prtcl=0x0000
> > device names: ugen1
> > usbd: Found action 'USB device' for product 0x3201, vendor 0x0419 at
ugen1
> > usbd: action 0: USB device
> > usbd: Setting DEVNAME='ugen1'
> >
> > (The following messages repeat indefinitely pausing for a while on the
doing
> > discovery bit)
> > usbd: doing timeout discovery on /dev/usb0
> > usbd: processing event queue due to timeout on /dev/usb
> > usbd: doing discovery on /dev/usb0
> > usbd: doing timeout discovery on /dev/usb0
> > usbd: processing event queue due to timeout on /dev/usb
> > (and so on....)
> >
> >
> > dmesg output:
> >
> > Copyright (c) 1992-2002 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> > The Regents of the University of California. All rights
reserved.
> > FreeBSD 4.6-STABLE #3: Thu Jul 18 19:06:38 EST 2002
> > jason@grody:/usr/obj/usr/src/sys/GRODY
> > Timecounter "i8254" frequency 1193182 Hz
> > CPU: Pentium II/Pentium II Xeon/Celeron (349.07-MHz 686-class CPU)
> > Origin = "GenuineIntel" Id = 0x652 Stepping = 2
> >
> >
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
> > CM
> > OV,PAT,PSE36,MMX,FXSR>
> > real memory = 402587648 (393152K bytes)
> > Programming 24 pins in IOAPIC #0
> > IOAPIC #0 intpin 2 -> irq 0
> > FreeBSD/SMP: Multiprocessor motherboard
> > cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
> > cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
> > io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
> > Preloaded elf kernel "kernel" at 0xc0311000.
> > Pentium Pro MTRR support enabled
> > Using $PIR table, 7 entries at 0xc00fddf0
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
> > IOAPIC #0 intpin 16 -> irq 2
> > IOAPIC #0 intpin 18 -> irq 16
> > pci0: <PCI bus> on pcib0
> > pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on
pci0
> > pci1: <PCI bus> on pcib1
> > isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
> > isa0: <ISA bus> on isab0
> > atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1
on
> > pci0
> > ata0: at 0x1f0 irq 14 on atapci0
> > ata1: at 0x170 irq 15 on atapci0
> > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xe000-0xe01f irq
11
> > at device 7.2 on pci0
> > usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
> > usb0: USB revision 1.0
> > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> > uhub0: 2 ports with 2 removable, self powered
> > Timecounter "PIIX" frequency 3579545 Hz
> > chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at
> > device 7.3 on pci0
> > pci0: <NVidia/SGS-Thomson Riva128 graphics accelerator> at 8.0 irq 2
> > sym0: <875> port 0xe400-0xe4ff mem
> > 0xe1101000-0xe1101fff,0xe1102000-0xe11020ff irq 16 at device 10.0 on
pci0
> > sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
> > sym0: open drain IRQ line driver, using on-chip SRAM
> > sym0: using LOAD/STORE-based firmware.
> > sym0: SCAN AT BOOT disabled for targets 3 4 6 8 9 10 11 12 13 14 15.
> > sym0: SCAN FOR LUNS disabled for targets 0 1 2 4 5 6.
> > fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xe800-0xe83f mem
> > 0xe1000000-0xe10fffff,0xe1100000-0xe1100fff irq 2 at device 12.0 on pci0
> > fxp0: Ethernet address 00:02:b3:0b:19:61
> > inphy0: <i82555 10/100 media interface> on miibus0
> > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff on isa0
> > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
> > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> > kbd0 at atkbd0
> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
> > sc0: <System console> at flags 0x100 on isa0
> > sc0: VGA <16 virtual consoles, flags=0x300>
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 16550A
> > sio1 at port 0x2f8-0x2ff irq 3 on isa0
> > sio1: type 16550A
> > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/16 bytes threshold
> > lpt0: <Printer> on ppbus0
> > lpt0: Interrupt-driven port
> > ppi0: <Parallel I/O> on ppbus0
> > APIC_IO: Testing 8254 interrupt delivery
> > APIC_IO: routing 8254 via IOAPIC #0 intpin 2
> > SMP: AP CPU #1 Launched!
> > ad0: 12971MB <WDC WD136AA> [26354/16/63] at ata0-master UDMA33
> > Waiting 10 seconds for SCSI devices to settle
> > (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
> > Mounting root from ufs:/dev/da0s1a
> > cd0 at sym0 bus 0 target 1 lun 0
> > cd0: <MATSHITA CD-ROM CR-508 XS03> Removable CD-ROM SCSI-2 device
> > cd0: 10.000MB/s transfers (10.000MHz, offset 16)
> > cd0: Attempt to query device size failed: NOT READY, Medium not present
> > da0 at sym0 bus 0 target 0 lun 0
> > da0: <IBM DCAS-34330W S65A> Fixed Direct Access SCSI-2 device
> > da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit)
> > da0: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
> > IP Filter: v3.4.27 initialized. Default = pass all, Logging = enabled
> >
> >
> >
> > To Unsubscribe: send mail to majordomo@FreeBSD.org
> > with "unsubscribe freebsd-hardware" in the body of the message
>
> To Unsubscribe: send mail to majordomo@FreeBSD.org
> with "unsubscribe freebsd-hardware" in the body of the message
>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?014601c22f8a$ea9aa1b0$0101a8c0>