Date: Sun, 18 Apr 2004 19:37:20 +0100 From: Francisco Alves Cabrita <francisco@nortenet.pt> To: imp@bsdimp.com Cc: freebsd-current@freebsd.org Subject: Re: Re: cardbus problems Message-ID: <1082313440.63250.14.camel@zarcon.homeunix.net> In-Reply-To: <20040418115324.F00BC16A528@hub.freebsd.org> References: <20040418115324.F00BC16A528@hub.freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
> In message: <1082226317.834.12.camel@zarcon.homeunix.net> > Francisco Alves Cabrita <francisco@nortenet.pt> writes: > : hello > : i'm running (i386)5-CURRENT and in this "nightly" buildwold ,, my > : cardbus (ethernet pcmcia ovislink chipset rl) didnt get enabled"" > : > : > : this was the message during boot: > : > : cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0 > : cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0 > : cardbus0: <CardBus bus> on cbb0 > : pccard0: <16-bit PCCard bus> on cbb0 > : cbb0: bad Vcc request. ctrl=0xf000ef08, status=0xf000e2c3 > : cbb_power: 0V > : cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0 > : cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x1000 > : cardbus1: <CardBus bus> on cbb1 > : pccard1: <16-bit PCCard bus> on cbb1 > : cbb1: bad Vcc request. ctrl=0x7720700, status=0x76f076c > : cbb_power: 0V > : > : can some one give a tip !!! > > Please submit an older, working dmesg. I think I know what's going > on, but w/o that, I can't be sure. > > Since the cbb is on pci0, I think that you might have an non-ACPI > system. Especially since the ToPIC95B is a relatively old chip. My > guess is that this is a 100-166MHz Pentium system. > > Warner Hellow Warner, thank for you response. Yes, you are almost right, is not an 100-166 Pentium , but and Toshiba (4300 series) Laptop 600Mhz with ACPI disabled for performence reasons, but here goes the boot message when was working: cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0 cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 and the result: rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x88002000-0x880021ff irq 11 at device 0.0 on cardbus1 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:10:60:75:66:fc rl0: [GIANT-LOCKED] since I installed 5.X here, i disabled the ACPI module, and didnt have any hardware problems until now, but i will tunr it on to see what appen. [] thanks Francisco
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1082313440.63250.14.camel>