Date: Tue, 12 Jan 1999 14:47:13 PST From: "Tyler Graham Cracker Carney Crust" <oriontwin@hotmail.com> To: freebsd-questions@FreeBSD.ORG Subject: problem getting my kernel to compile Message-ID: <19990112224713.18683.qmail@hotmail.com>
next in thread | raw e-mail | index | archive | help
I'm having a problem compiling my new kernel (MATLOCK). I've modified the GENERIC kernel for use with my machine then run it through /usr/sbin/config which runs cleanly. I cd to ../../compile/MATLOCK and when I type in "make depend" it STOPs on an error and reports: make: don't know how to make ../../kern/vnode_if.sh. Stop Any idea what I've done wrong? Thanx in advance. My modified version of GENERIC is as follows: #MATLOCK's first kernel # machine "i386" #cpu "I386_CPU" #cpu "I486_CPU" cpu "I586_CPU" #cpu "I686_CPU" ident MATLOCK maxusers 15 #options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options NFS #Network Filesystem #options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15 #Be pessimistic about Joe SCSI device options BOUNCE_BUFFERS #include support for DMA bounce buffers options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on wd0 controller isa0 controller eisa0 controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 #disk fd1 at fdc0 drive 1 #tape ft0 at fdc0 drive 2 options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 #disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr #disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM device wcd0 #IDE CD-ROM #device wfd0 #IDE floppy (LS-120) # A single entry for any of these controllers (ncr, ahb, ahc, amd) is # sufficient for any number of installed devices. # # Note: The dpt driver is present in this release but was left disabled # due to its relatively late entry (it's almost certainly benign to enable # it but we didn't want to risk any chance of destabilizing 2.2.6). To # enable DPT support, uncomment the dpt0 controller entry and the two # options DPTOPT and DPT_MEASURE_PERFORMANCE entries below. #controller ncr0 #controller amd0 #controller ahb0 #controller ahc0 #controller dpt0 #controller bt0 at isa? port "IO_BT0" bio irq ? vector bt_isa_intr #controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr #controller aha0 at isa? port "IO_AHA0" bio irq ? drq 5 vector ahaintr #controller aic0 at isa? port 0x340 bio irq 11 vector aicintr #controller nca0 at isa? port 0x1f88 bio irq 10 vector ncaintr #controller nca1 at isa? port 0x350 bio irq 5 vector ncaintr #controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr #options DPTOPT # will go away soon #options DPT_MEASURE_PERFORMANCE # just enable for now #options DPT_VERIFY_HINTR # Some hardware must have it! #options DPT_TRACK_CCB_STATES # Some hardware must have it! #options DPT_HANDLE_TIMEOUTS # Some hardware must have it! #options DPT_TIMEOUT_FACTOR=4 # Some hardware needs more #controller scbus0 #device sd0 #device od0 #See LINT for possible `od' options. #device st0 #device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr #device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr #controller matcd0 at isa? port 0x230 bio #device scd0 at isa? port 0x230 bio # syscons is the default console driver, resembling an SCO console device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Mandatory, don't remove device npx0 at isa? port "IO_NPX" flags 0x1 irq 13 vector npxintr # # Laptop support (see LINT for more options) # device apm0 at isa? disable # Advanced Power Management options APM_BROKEN_STATCLOCK # Workaround some buggy APM BIOS # PCCARD (PCMCIA) support #controller card0 #device pcic0 at card? #device pcic1 at card? device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr device sio2 at isa? disable port "IO_COM3" tty irq 5 vector siointr device sio3 at isa? disable port "IO_COM4" tty irq 9 vector siointr device lpt0 at isa? port? tty irq 7 vector lptintr #device lpt1 at isa? port? tty #device mse0 at isa? port 0x23c tty irq 5 vector mseintr device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. #device de0 #device fxp0 #device tx0 #device vx0 device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 vector edintr #device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000 vector ieintr #device ep0 at isa? port 0x300 net irq 10 vector epintr #device ex0 at isa? port? net irq? vector exintr #device fe0 at isa? port 0x300 net irq ? vector feintr #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr #device lnc0 at isa? port 0x280 net irq 10 drq 0 vector lncintr #device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr #device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr pseudo-device loop pseudo-device ether pseudo-device log pseudo-device sl 1 pseudo-device ppp 1 pseudo-device vn 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory. # options SYSVSHM ______________________________________________________ Get Your Private, Free Email at http://www.hotmail.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19990112224713.18683.qmail>