Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 23 Dec 2003 14:09:42 +0000
From:      "Drew Robertson" <the_brothel@hotmail.com>
To:        freebsd-questions@freebsd.org
Subject:   IPFW Rule set question...
Message-ID:  <BAY99-F62TzOLkM1U5l00021e76@hotmail.com>

next in thread | raw e-mail | index | archive | help

Hi everyone,

Thanks to those who take the time to read and reply to these emails.

I have a strange issue regarding my firewall (IPFW)...

I have enabled SSH, TELNET and FTP on my freeBSD 4.8 box at home... it is 
dual homed, 2 NICs one for the internal LAN one running my cable modem.  
Everything works fine on the internal side.

When accessing the box using any of those apps from work, the system looks 
to briefly connect and then returns a "Connection Lost" or "Connection 
closed by remote host error".

The command setup to allow in access is as follows...

820 allow log tcp from any to me 22 limit src-addr 4 in recv tl0 setup
830 allow log tcp from any to me 23 limit src-addr 4 in recv tl0 setup

when this didn't work I added another command at the start of the ruleset to 
just let everything in from a particular IP address range...

202 allow ip from 203.10.10.0/24 to any

however this produced the same error...

It wasn't until I allowed all from any to any that I was able to connect...

When checking out the security log, it tells me that rule 820 is allowing 
access to my computer at home...


Ruleset is attached completely below

/sbin/ipfw -q -f flush

# Set rules command prefix
# The -q option on the command is for quite mode.
# Do not display rules as they load. Remove during development to see.
cmd="/sbin/ipfw -q add"

# Set defaults
oif="tl0"                    # Nic card to cable modem public internet 
connection
odns1="203.2.75.132"      # ISP's dns server IP address

$cmd 00200 divert natd all from any to any via $oif


########  control section  ############################################
# Start of IPFW advanced Stateful Filtering using "dynamic" rules.
# The check-state statement behavior is to match bi-directional packet 
traffic
# flow between source and destination using protocol/IP/port/sequence 
number.
# The dynamic rule has a limited lifetime which is controlled by a set of
# sysctl(8) variables. The lifetime is refreshed every time a matching
# packet is found in the dynamic table.

# Allow the packet through if it has previous been added to the
# the "dynamic" rules table by an allow keep-state statement.

$cmd 00202 allow log all from 203.10.10.0/24 to any
$cmd 00203 allow log all from any to any via tun0

$cmd 00400 check-state


# SAMBA File/Printer Sharing on Internal LAN
$cmd 0410 allow log tcp from 192.168.1.0/24 to 192.168.1.0/24
$cmd 0411 allow log udp from 192.168.1.0/24 to 192.168.1.0/24

# Run all private LAN xl0 packet traffic through the dynamic rules
# table so the IP address are in sync with Natd.
$cmd 00500 allow log all from any to any via sis0 keep-state

# Deny all fragments as bogus packets
$cmd 00530 deny log all from any to any frag in via $oif

# Deny  ACK packets that did not match the dynamic rule table
$cmd 00540 deny log tcp from any to any established in via $oif

########  outbound section  ############################################
# Interrogate packets originating from behind the firewall, private net.
# Upon a rule match, it's keep-state option will create a dynamic rule.

# Allow out non-secure standard http function
$cmd 00600 allow log tcp  from any to any 80  out via $oif setup keep-state

# Allow out secure www function https over TLS SSL
$cmd 00601 allow log tcp  from any to any 443 out via $oif setup keep-state

# Allow out access to my ISP's Domain name server.
$cmd 00610 allow log tcp  from any to $odns1 53 out via $oif setup 
keep-state
$cmd 00611 allow log udp  from any to $odns1 53 out via $oif keep-state

# Allow out send & get email function
$cmd 00630 allow log tcp from any to any 25,110 out via $oif setup 
keep-state

# Allow out & in FBSD (make install & CVSUP)  functions
# Basically give user id [ROOT]  "GOD"  privileges.
$cmd 00640 allow log tcp from me to any out via $oif setup keep-state uid 
root

########  inbound section  ############################################
# Interrogate packets originating from in front of the firewall, public net.

# Allow in www http access to my apache server
#$cmd 00800 allow log tcp from any to any 80 in via $oif setup keep-state 
limit src-addr 4

# Allow  TCP FTP control channel in & data channel out
$cmd 00810 allow log tcp from any to me 21  in via $oif setup keep-state 
limit src-addr 4
$cmd 00811 allow log tcp from any 20 to any 1024-49151 out via $oif setup 
keep limit src-addr 4

# Allow in ssh function
$cmd 00820 allow log tcp from any to me 22 in via $oif setup keep-state 
limit src-addr 4

# Allow in Telnet
$cmd 00830 allow log tcp from any to me 23 in via $oif setup keep-state 
limit src-addr 4


Thanks.

D

_________________________________________________________________
ninemsn Premium transforms your e-mail with colours, photos and animated 
text. Click here  http://ninemsn.com.au/premium/landing.asp



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BAY99-F62TzOLkM1U5l00021e76>