Date: Tue, 14 Oct 1997 15:14:47 -0700 (PDT) From: David Filo <filo@yahoo.com> To: freebsd-questions@FreeBSD.ORG Subject: FreeBSD on Intel's AL440LX Board Message-ID: <199710142214.PAA21605@ns2.yahoo.com>
next in thread | raw e-mail | index | archive | help
Has anyone been successful in getting FreeBSD running on the Intel
AL440LX motherboard? We've tried both 2.1 and 3.0 and both have
problems. Booting from floppy works fine, but booting from the scsi
drive (after install) either gives "read error" in 2.1 or no message
at all under 3.0 immediately following the normal bios stuff.
Seems to be something related to the MBR since it will boot fine from
the drive at the floppy boot prompt (i.e. sd(0,1)kernel with floppy
boot). In both cases the hard drive was formatted to not use slices
(dedicate entire drive to FreeBSD), so no boot manager is being used.
Bios setting for the motherboard and adaptec are normal (i.e. similar
settings on other combos have worked fine). In addition various bios
changes were made with no effect. Basically have run out of things to
try. Any ideas, or things to try?
dmesg output (with 3.0) is:
Copyright (c) 1992-1997 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.0-971012-SNAP #0: Sun Oct 12 09:37:38 GMT 1997
root@make.ican.net:/usr/src/sys/compile/GENERIC
CPU: Pentium Pro (299.94-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x633 Stepping=3
Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 268435456 (262144K bytes)
avail memory = 260206592 (254108K bytes)
Probing for devices on PCI bus 0:
chip0: <Host to PCI bridge (vendor=8086 device=7180)> rev 0x03 on pci0.0.0
chip1: <PCI to PCI bridge (vendor=8086 device=7181)> rev 0x03 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x01 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip3: <Intel 82371AB USB host controller> rev 0x01 int d irq 11 on pci0.7.2
chip4: <Intel 82371AB power management> rev 0x01 on pci0.7.3
ahc0: <Adaptec 2940 Ultra SCSI host adapter> rev 0x00 int a irq 10 on pci0.13.0
ahc0: aic7880 Wide Channel, SCSI Id=7, 16 SCBs
ahc0: waiting for scsi devices to settle
scbus0 at ahc0 bus 0
sd0 at scbus0 target 1 lun 0
sd0: <SEAGATE ST34501W 0017> type 0 fixed SCSI 2
sd0: Direct-Access 4339MB (8887200 512 byte sectors)
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x02 int a irq 15 on pci0.14.0
fxp0: Ethernet address 00:a0:c9:70:05:2d
vga0: <VGA-compatible display device> rev 0xd3 int a irq 9 on pci0.15.0
Probing for devices on PCI bus 1:
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 not found at 0x2f8
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
npx0 on motherboard
npx0: INT 16 interface
changing root device to sd0a
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199710142214.PAA21605>