Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 5 Jan 2009 06:46:47 +0100
From:      Konstantin Saurbier <konstantin@saurbier.net>
To:        freebsd-sparc64@freebsd.org
Subject:   Success on Blade 1000 (20081209 snapshot iso)
Message-ID:  <3D3A0185-45F3-45D2-948B-5EFFB3C7E69E@saurbier.net>

next in thread | raw e-mail | index | archive | help
This is an OpenPGP/MIME signed message (RFC 2440 and 3156)
--Apple-Mail-1--575862623
Content-Type: text/plain; charset=US-ASCII; format=flowed; delsp=yes
Content-Transfer-Encoding: 7bit

Hi Marius,

I've tried the 8.0-20081209-SNAP-sparc64-disc1.iso.gz on my
Blade 1000 (Dual US3 750MHz, 1GB Ram, 18GB FC-HDD).
Earlier snapshots crashed while probing the firewire controller,
but that seems to be fixed. Just one LOR.


Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-20081209-SNAP #0: Tue Dec  9 19:08:40 UTC 2008
     root@nimrod.franken.de:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
real memory  = 1073741824 (1024 MB)
avail memory = 1030889472 (983 MB)
cpu0: Sun Microsystems UltraSparc-III Processor (750.00 MHz CPU)
cpu1: Sun Microsystems UltraSparc-III Processor (750.00 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
ispfw: registered firmware <isp_1000>
ispfw: registered firmware <isp_1040>
ispfw: registered firmware <isp_1040_it>
ispfw: registered firmware <isp_1080>
ispfw: registered firmware <isp_1080_it>
ispfw: registered firmware <isp_12160>
ispfw: registered firmware <isp_12160_it>
ispfw: registered firmware <isp_2100>
ispfw: registered firmware <isp_2200>
ispfw: registered firmware <isp_2300>
ispfw: registered firmware <isp_2322>
ispfw: registered firmware <isp_2400>
kbd0 at kbdmux0
nexus0: <Open Firmware Nexus device>
nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type  
memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40000c00000-0x40000c00047 type  
memory-controller (no driver attached)
pcib0: <Sun Host-PCI bridge> mem 0x40004700000-0x40004717fff, 
0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq  
563,560,561,564,550 on nexus0
pcib0: Schizo, version 4, IGN 0x8, bus B, 33MHz
pcib0: DVMA map: 0xc0000000 to 0xffffffff
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [FILTER]
pci0: <OFW PCI bus> on pcib0
ebus0: <PCI-EBus3 bridge> mem 0x7d000000-0x7dffffff, 
0x7e000000-0x7e7fffff at device 5.0 on pci0
ebus0: <flashprom> addr 0-0x1fffff (no driver attached)
ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no  
driver attached)
ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached)
ebus0: <ppm> addr  
0x10000000e 
-0x100000028,0x100728000-0x100728003,0x10030002e-0x10030002f, 
0x100300600-0x100300607 (no driver attached)
ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached)
ebus0: <beep> addr 0x100000032-0x100000037 (no driver attached)
ebus0: <audio> addr 0x100200000-0x1002000ff,0x100702000-0x10070200f, 
0x100704000-0x10070400f,0x100722000-0x100722003 irq 32,33 (no driver  
attached)
rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0
ebus0: <gpio> addr 0x100300600-0x100300607 (no driver attached)
ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached)
ebus0: <floppy> addr 0x1003023f0-0x1003023f7,0x100706000-0x10070600f, 
0x100720000-0x100720003 irq 37 (no driver attached)
ebus0: <parallel> addr 0x100300278-0x100300287,0x10030002e-0x10030002f, 
0x100700000-0x10070000f irq 28 (no driver attached)
scc0: <Siemens SAB 82532 dual channel SCC> addr  
0x100400000-0x10040007f irq 34 on ebus0
scc0: [FILTER]
uart0: <SAB 82532 v3.2, channel A> on scc0
uart0: [FILTER]
uart0: CTS oflow
uart1: <SAB 82532 v3.2, channel B> on scc0
uart1: [FILTER]
uart1: CTS oflow
gem0: <Sun ERI 10/100 Ethernet> mem 0x100000-0x11ffff at device 5.1 on  
pci0
miibus0: <MII bus> on gem0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: 2kB RX FIFO, 2kB TX FIFO
gem0: Ethernet address: 00:03:ba:02:91:4e
gem0: [ITHREAD]
fwohci0: <Sun PCIO-2> mem 0x120000-0x1207ff,0x122000-0x1227ff at  
device 5.2 on pci0
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:03:ba:ff:fe:02:91:4e
fwohci0: Phy 1394a available S400, 4 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:03:ba:02:91:4e
fwe0: Ethernet address: 02:03:ba:02:91:4e
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:03:ba:ff:fe:02:91:4e @ 0xfffe00000000,  
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xc1128000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device  
5.3 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <Sun PCIO-2 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on  
usb0
uhub0: 4 ports with 4 removable, self powered
sym0: <875> port 0x300-0x3ff mem 0x124000-0x1240ff,0x126000-0x126fff  
at device 6.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: [ITHREAD]
sym1: <875> port 0x400-0x4ff mem 0x128000-0x1280ff,0x12a000-0x12afff  
at device 6.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: [ITHREAD]
pcib1: <Sun Host-PCI bridge> mem 0x40004600000-0x40004617fff, 
0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq  
562,560,561,564,551 on nexus0
pcib1: Schizo, version 4, IGN 0x8, bus A, 66MHz
Timecounter "pcib1" frequency 150000000 Hz quality 100
pcib1: DVMA map: 0xc0000000 to 0xffffffff
pcib1: [FILTER]
pci1: <OFW PCI bus> on pcib1
isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem  
0x100000-0x100fff at device 4.0 on pci1
isp0: [ITHREAD]
isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6
isp0: invalid NVRAM header
isp0: invalid NVRAM header
upa0: <UPA bridge> mem 0x40004480000-0x4000448001f, 
0x40004706000-0x4000470600f,0x40004708000-0x4000470800f on nexus0
creator0: <Creator3D> mem 0x1c000000000-0x1c0000003ff, 
0x1c000400000-0x1c0005fffff,0x1c000600000-0x1c0007fffff, 
0x1c001000000-0x1c0013fffff,0x1c001400000-0x1c0017fffff, 
0x1c001800000-0x1c001bfffff,0x1c001c00000-0x1c001ffffff, 
0x1c002000000-0x1c002ffffff,0x1c003000000-0x1c003ffffff, 
0x1c004000000-0x1c0043fffff,0x1c004400000-0x1c0047fffff, 
0x1c004800000-0x1c004bfffff,0x1c004c00000-0x1c004ffffff, 
0x1c005000000-0x1c005ffffff,0x1c006000000-0x1c007ffffff, 
0x1c009000000-0x1c0097fffff,0x1c009800000-0x1c009ffffff, 
0x1c00a000000-0x1c00affffff,0x1c00b000000-0x1c00b7fffff, 
0x1c00b800000-0x1c00bffffff,0x1c00c000000-0x1c00c3fffff, 
0x1c00c800000-0x1c00cffffff,0x1c00d000000-0x1c00d7fffff, 
0x1c00d800000-0x1c00dffffff irq 554 on upa0
creator0: console
creator0: resolution 1280x1024
schppm0: <Schizo power management> mem 0x40004410050-0x40004410057 on  
nexus0
syscons0: <System console> on nexus0
syscons0: Unknown <16 virtual consoles, flags=0x300>
ums0: <vendor 0x0430 product 0x0100, class 0/0, rev 1.00/1.02, addr 2>  
on uhub0
ums0: 3 buttons.
ukbd0: <vendor 0x0430 product 0x0005, class 0/0, rev 1.00/1.02, addr  
3> on uhub0
kbd1 at ukbd0
Timecounter "tick" frequency 750000000 Hz quality 10
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
da0 at isp0 bus 0 target 0 lun 0
da0: <SEAGATE ST318304FSUN18G 042D> Fixed Direct Access SCSI-3 device
da0: 100.000MB/s transfers
da0: Command Queueing Enabled
da0: 17274MB (35378533 512 byte sectors: 255H 63S/T 2202C)
SMP: AP CPU #1 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
cd0 at sym0 bus 0 target 0 lun 0
cd0: <TOSHIBA DVD-ROM SD-M1401 1009> Removable CD-ROM SCSI-2 device
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/da0a
Invalid time in real time clock.
Check and reset the date immediately!
lock order reversal:
  1st 0xfffff800010a6070 user map (user map) @ /usr/src/sys/vm/ 
vm_map.c:3115
  2nd 0xfffff8000158b130 ufs (ufs) @ /usr/src/sys/kern/vfs_subr.c:2079
KDB: stack backtrace:
_witness_debugger() at _witness_debugger+0x38
witness_checkorder() at witness_checkorder+0xcf8
__lockmgr_args() at __lockmgr_args+0x2d0
ffs_lock() at ffs_lock+0x88
VOP_LOCK1_APV() at VOP_LOCK1_APV+0x110
_vn_lock() at _vn_lock+0x80
vget() at vget+0x120
vnode_pager_lock() at vnode_pager_lock+0x240
vm_fault() at vm_fault+0x208
trap_pfault() at trap_pfault+0x198
trap() at trap+0xd0
-- fast data access mmu miss tar=0x2a3000 %o7=0xc0081208 --
userland() at 0x10015c
user trace: trap %o7=0xc0081208
pc 0x10015c, sp 0x7fdffffe531
pc 0, sp 0x7fdffffe5f1
done

Great work! Thank you for bringing FreeBSD to my Blade :-)

Konstantin

--Apple-Mail-1--575862623
content-type: application/pgp-signature; x-mac-type=70674453;
	name=PGP.sig
content-description: Signierter Teil der Nachricht
content-disposition: inline; filename=PGP.sig
content-transfer-encoding: 7bit

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.8 (Darwin)

iEYEARECAAYFAklhnscACgkQWkvQTx5k+y6UGQCdGsgCpgQXmqCcspzcS8m0BOEO
9ewAn0lhZift47HPa5hG13Cnimqgn/GV
=nmJ/
-----END PGP SIGNATURE-----

--Apple-Mail-1--575862623--



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3D3A0185-45F3-45D2-948B-5EFFB3C7E69E>