Date: Fri, 28 Apr 1995 00:29:22 -0700 (PDT) From: julian@TFS.COM (Julian Elischer) To: hackers@FreeBSD.org Subject: NCR SCSI failure (failure to convert linux user) Message-ID: <m0s4kUN-0003wOC@TFS.COM>
next in thread | raw e-mail | index | archive | help
here is the error message from the FreeBSD NCR driver.. it failed badly.. linux runs on this device ok (but slow) julian ========== ncr0 targ0?: ERROR(80:140) (8-2a-0)(8/13) @ (404:900b0000). reg: da 10 80 13 47 8 0 1f 3 8 80 2a 80 0 2 0 . ncr0: restart (fatal error). ncr0: reset by timeout. sd0(ncr0:0:0); FAST SCSI-2 100ns (10MB/sec) offset 8. sd: error reading primary partition table reading fsbn 0 (sd0 bn 0; cn 0 tn 0 sn 0) ========== below is the linux dmesg output, and other information.. Forwarded message: > From idiom.com!jason Fri Apr 28 00:16:31 1995 > Message-Id: <199504280720.AAA22949@idiom.com> > X-Authentication-Warning: idiom.com: Host localhost didn't use HELO protocol > To: julian@tfs.com > Subject: dmesg from linux > Date: Fri, 28 Apr 1995 00:20:25 -0700 > From: Jason Venner <jason@idiom.com> > > > PCI/I - P54NP4D mother board. > > card is an SC-200 NCR53C810 > > Console: colour EGA+ 80x25, 1 virtual console (max 63) > bios32_init : BIOS32 Service Directory structure at 0x000fc7e0 > bios32_init : BIOS32 Service Directory entry at 0xfcc10 > pcibios_init : PCI BIOS revision 2.00 entry at 0xfcc40 > Probing PCI hardware. > PCI bridge optimisation. > Cache L2 : Not supported. > CPU-PCI posted write : on. > CPU-Memory posted write : on. > PCI-Memory posted write : on. > PCI burst : on. > Calibrating delay loop.. ok - 39.94 BogoMips > Serial driver version 4.11 with no serial options enabled > tty00 at 0x03f8 (irq = 4) is a 16550A > tty01 at 0x02f8 (irq = 3) is a 16550A > lp1 at 0x0378, using polling driver > snd2 <SoundBlaster Pro 4.5> at 0x220 irq 5 drq 1 > snd6 <SoundBlaster 16 4.5> at 0x220 irq 5 drq 5 > snd7 <SoundBlaster MPU-401> at 0x330 irq 5 drq 0 > snd1 <Yamaha OPL-3 FM> at 0x388 irq 0 drq 0 > mcd=0x300,10: Init failed. No mcd device at 0x300 irq 10 > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > scsi-ncr53c7,8xx : at PCI bus 0, device 4, function 0 > scsi-ncr53c7,8xx : NCR53c810 at memory 0xfbfef000, io 0xe800, irq 14 > scsi0 : using io mapped access > scsi0 : using initiator ID 7 > scsi0 : using level active interrupts > scsi0 : burst length 8 > scsi0 : using 40MHz SCSI clock > scsi0 : NCR code relocated to 0x3dc880 > scsi0 : test 1 started > scsi0 : NCR53c{7,8}xx (rel 4) > scsi : 1 host. > Vendor: QUANTUM Model: XP34301 Rev: 102B > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sda at scsi0, id 0, lun 0 > Vendor: QUANTUM Model: PD1800S Rev: 3162 > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sdb at scsi0, id 1, lun 0 > Vendor: FUJITSU Model: M2694ES-512 Rev: 812A > Type: Direct-Access ANSI SCSI revision: 02 > Detected scsi disk sdc at scsi0, id 2, lun 0 > Vendor: PLEXTOR Model: CD-ROM PX-4XCH Rev: 1.23 > Type: CD-ROM ANSI SCSI revision: 02 > Detected scsi CD-ROM sr0 at scsi0, id 3, lun 0 > Vendor: WANGTEK Model: 6200-HS Rev: 4B18 > Type: Sequential-Access ANSI SCSI revision: 02 > Detected scsi tape st0 at scsi0, id 4, lun 0 > scsi : detected 1 SCSI tape 1 SCSI cdrom 3 SCSI disks total. > SCSI Hardware sector size is 512 bytes on device sda > SCSI Hardware sector size is 512 bytes on device sdb > SCSI Hardware sector size is 512 bytes on device sdc > Memory: 29160k/32768k available (796k kernel code, 384k reserved, 2428k data) > This processor honours the WP bit even when in supervisor mode. Good. > Swansea University Computer Society NET3.019 > Swansea University Computer Society TCP/IP for NET3.019 > IP Protocols: IGMP, ICMP, UDP, TCP > PPP: version 0.2.7 (4 channels) NEW_TTY_DRIVERS OPTIMIZE_FLAGS > TCP compression code copyright 1989 Regents of the University of California > PPP line discipline registered. > SLIP: version 0.8.3-NET3.019-NEWTTY (16 channels) (6 bit encapsulation enabled) > CSLIP: code copyright 1989 Regents of the University of California > eth0: 3c509 at 0x300 tag 1, AUI port, address 00 20 af 6b ac 98, IRQ 7. > 3c509.c:1.03 10/8/94 becker@cesdis.gsfc.nasa.gov > Checking 386/387 coupling... Ok, fpu using exception 16 error reporting. > Checking 'hlt' instruction... Ok. > Linux version 1.2.6 (root@anami) (gcc version 2.6.3) #9 Mon Apr 24 08:39:30 PDT 1995 > Partition check: > sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 > > sdb: sdb1 sdb2 sdb3 > sdc: sdc1 sdc2 sdc3 >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?m0s4kUN-0003wOC>