Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 6 Oct 2000 11:57:35 -0700 (PDT)
From:      Matthew Jacob <mjacob@feral.com>
To:        John Baldwin <jhb@FreeBSD.org>
Cc:        alpha@FreeBSD.org
Subject:   red face better...
Message-ID:  <Pine.LNX.4.21.0010061153350.15440-100000@zeppo.feral.com>
In-Reply-To: <XFMail.001006094056.jhb@FreeBSD.org>

next in thread | previous in thread | raw e-mail | index | archive | help

...but not quite there yet....

Got around the 4MB hang issue, but now hang probing the SCSI bus (see below)

I don't think that we're quite all happiness with 'compatibility' yet- so I
think I'll do some fooling around to try and finishing some locking in the
Qlogic driver (it should be just about ready to go....)...

-matt
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel] in 9 seconds...
Booting [kernel]... 
Entering kernel at 0xfffffc00003282a0..
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
Setting atkbd 0 at to atkbdc (string)
Setting atkbd 0 irq to 1 (int)
Setting atkbdc 0 at to isa (string)
Setting atkbdc 0 port to 96 (int)
Setting fd 0 at to fdc0 (string)
Setting fd 0 drive to 0 (int)
Setting fdc 0 at to isa (string)
Setting fdc 0 drq to 2 (int)
Setting fdc 0 irq to 6 (int)
Setting fdc 0 port to 1008 (int)
Setting mcclock 0 at to isa (string)
Setting mcclock 0 port to 112 (int)
Setting ppc 0 at to isa (string)
Setting ppc 0 irq to 7 (int)
Setting psm 0 at to atkbdc (string)
Setting psm 0 irq to 12 (int)
Setting sc 0 at to isa (string)
Setting sio 0 at to isa (string)
Setting sio 0 irq to 4 (int)
Setting sio 0 port to 1016 (int)
Setting sio 1 at to isa (string)
Setting sio 1 flags to 80 (int)
Setting sio 1 irq to 3 (int)
Setting sio 1 port to 760 (int)
Setting vga 0 at to isa (string)
FreeBSD 5.0-CURRENT #0: Fri Oct  6 11:35:18 PDT 2000
    mjacob@farrago.feral.com:/tstsys/compile/FARRAGO
EB164
Digital AlphaPC 164 432 MHz, 432MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=1 extensions=0x1<BWX>
OSF PAL rev: 0x1000800020117
real memory  = 265904128 (259672K bytes)
Physical memory chunk(s):
0x006c4000 - 0x0ff0dfff, 260349952 bytes (31781 pages)
avail memory = 252608512 (246688K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00006a4000.
Preloaded elf module "ispfw.ko" at 0xfffffc00006a40c0.
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
cia0: <2117x Core Logic chipset>
cia0: ALCOR/ALCOR2, pass 3
cia0: extended capabilities: 21<DWEN,BWEN>
pcib0: <2117x PCI host bus adapter> on cia0
pci0: physical bus=0
found->	vendor=0x1077, dev=0x1020, revid=0x05
	bus=0, slot=5, func=0
	class=01-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=2
	map[10]: type 4, range 32, base 00010200, size  8, enabled
	map[14]: type 1, range 32, base 82082000, size 12, enabled
found->	vendor=0x1077, dev=0x1080, revid=0x01
	bus=0, slot=6, func=0
	class=01-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=0
	map[10]: type 4, range 32, base 00010100, size  8, enabled
	map[14]: type 1, range 32, base 82081000, size 12, enabled
found->	vendor=0x1077, dev=0x2200, revid=0x05
	bus=0, slot=7, func=0
	class=01-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=1
	map[10]: type 4, range 32, base 00010000, size  8, enabled
	map[14]: type 1, range 32, base 82080000, size 12, enabled
found->	vendor=0x8086, dev=0x0484, revid=0x43
	bus=0, slot=8, func=0
	class=00-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
found->	vendor=0x1011, dev=0x0009, revid=0x22
	bus=0, slot=9, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=3
	map[10]: type 4, range 32, base 00010300, size  7, enabled
	map[14]: type 1, range 32, base 82083000, size  7, enabled
found->	vendor=0x1095, dev=0x0646, revid=0x01
	bus=0, slot=11, func=0
	class=01-01-80, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[20]: type 4, range 32, base 00010380, size  4, enabled
pci0: <PCI bus> on pcib0
Qlogic ISP Driver, FreeBSD Version 5.3, Core Version 2.0
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x10200-0x102ff mem 0x82082000-0x82082fff irq 2 at device 5.0 on pci0
isp0: using Memory space register mapping
isp0: interrupting at CIA irq 2
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, loaded F/W Revision 4.65.0
isp0: Last F/W revision was 5.57.1
isp1: <Qlogic ISP 1080 PCI SCSI Adapter> port 0x10100-0x101ff mem 0x82081000-0x82081fff irq 0 at device 6.0 on pci0
isp1: using Memory space register mapping
isp1: interrupting at CIA irq 0
isp1: bus 0 is in LVD Mode
isp1: Board Revision 1080, loaded F/W Revision 8.13.0
isp1: Last F/W revision was 8.13.0
isp2: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x10000-0x100ff mem 0x82080000-0x82080fff irq 1 at device 7.0 on pci0
isp2: using Memory space register mapping
isp2: interrupting at CIA irq 1
isp2: Board Revision 2200, loaded F/W Revision 2.1.14
isp2: Last F/W revision was 2.1.14
isp2: NVRAM Derived Node WWN 0x200000e08b01ae8b
isp2: NVRAM Derived Port WWN 0x200300e08b01ae8b
isab0: <Intel 82378IB PCI to ISA bridge> at device 8.0 on pci0
	Bus Modes: Bus Park, Resource Lock,
	Configuration RAM: 0C00h,0800h-08FFh
	Port 92: enabled
isa0: <ISA bus> on isab0
pci0: <unknown card> (vendor=0x1011, dev=0x0009) at 9.0 irq 3
atapci0: <CMD 646 ATA controller> port 0x10380-0x1038f irq 5 at device 11.0 on pci0
atapci0: Busmastering DMA enabled
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x10380
ata0: mask=03 status0=51 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0: at 0x1f0 irq 14 on atapci0
ata0: interrupting at ISA irq 14
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x10388
ata1: mask=00 status0=ff status1=ff
ata1: probe allocation failed
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc-: sc0 already exists, using sc1 instead
vga-: vga0 already exists, using vga1 instead
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000
atkbd0: interrupting at ISA irq 1
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 433005984 Hz (firmware 432900432 Hz)
i8254 clock: 1192005 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
ppc0 failed to probe at irq 7 on isa0
sc0: no video adapter is found.
sc0: <System console> failed to probe on isa0
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1: reserved for low-level i/o
sio1 failed to probe at port 0x2f8-0x2ff irq 3 flags 0x50 on isa0
vga0: <Generic ISA VGA> failed to probe on isa0
sc1: no video adapter is found.
sc1: <System console> failed to probe on isa0
vga1: <Generic ISA VGA> failed to probe on isa0
isa_probe_children: probing PnP devices
Timecounter "i8254"  frequency 1193182 Hz
Timecounter "alpha"  frequency 433005984 Hz
bpf: lo0 attached
ata0-master: success setting WDMA2 on CMD chip
ad0: <ST33210A/3.04> ATA-4 disk at ata0-master
ad0: 3098MB (6346368 sectors), 6296 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, WDMA2
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
Creating DISK ad0
Waiting 2 seconds for SCSI devices to settle
[ hangs ]



To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.LNX.4.21.0010061153350.15440-100000>